journal article·2024

EFFECT OF FLASH-BOILING AND AIR-ASSISTED INJECTION ON METHANOL SPRAY CHARACTERISTICS

Maohui Su, Jiaqing Ding, Kai Liu, Cangsu Xu, Wenhua Zhou

Atomization and Sprays· Volume 34· Issue 10
Publisher page

Abstract

The advantages of methanol as an alternative fuel have been well demonstrated. However, the difficulty of atomization restricts its practical application. Also, flash-boiling and air-assisted injection have been shown to improve the atomization quality of fuels. In this work, the methanol spray characteristics with and without air assistance were experimentally investigated. The experimental conditions include flash-boiling and non-flash-boiling states. High-speed backlight imaging and a Malvern laser particle size analyzer were used to obtain the spray images and droplet sizes, respectively. The flash-boiling state caused a significant variation in spray morphology and the formation of high-concentration central plumes with greater velocity. Compared to the non-flash-boiling spray, the droplet size of the central plumes is larger, whereas the peripheral droplets have a smaller particle size. The droplet size of the air-assisted spray at normal temperature and pressure can reach approximately 3.5 μm, whereas that of the methanol spray without air assistance under a strong flash-boiling state is approximately 60 μm, indicating that air-assisted injection can significantly improve the atomization quality of methanol spray. Furthermore, because of the good atomization, the air-assisted methanol spray is significantly affected by evaporation at high temperatures, and no significant transition of a flash-boiling state was observed.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Combustion Engine Technologies · Electrohydrodynamics and Fluid Dynamics · Aerosol Filtration and Electrostatic Precipitation

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (45)

Show source-provided references
1. Aleiferis, P.G. and van Romunde, Z.R., An Analysis of Spray Development with Iso-Octane, n-Pentane, Gasoline, Ethanol and n-Butanol from a Multi-Hole Injector under Hot Fuel Conditions, Fuel, vol. 105, pp. 143-168, 2013.10.1016/j.fuel.2012.07.044 ↗
2. Badawy, T., Xu, H., and Li, Y., Macroscopic Spray Characteristics of Iso-Octane, Ethanol, Gasoline and Methanol from a Multi-Hole Injector under Flash Boiling Conditions, Fuel, vol. 307, p. 121820, 2022.10.1016/j.fuel.2021.121820 ↗
3. Bp, Bp Statistical Review of World Energy 2022, London, England, 2022.
4. Cathcart, G., Dickson, G., and Ahern, S., The Application of Air-Assist Direct Injection for Spark-Ignited Heavy Fuel 2-Stroke and 4-Stroke Engines, SAE Technical Paper Series, 2005.10.4271/2005-32-0065 ↗
5. Cathcart, G., Houston, R., and Ahern, S., The Potential of Gasoline Direct Injection for Small Displacement 4-Stroke Motorcycle Applications, SAE International, 2004.10.4271/2004-32-0098 ↗
6. Cathcart, G. and Tubb, J., Application of Air Assisted Direct Fuel Injection to Pressure Charged Gasoline Engines, SAE International, 2002.10.4271/2002-01-0705 ↗
7. Chuayboon, S., Abanades, S., and Rodat, S., Syngas Production via Solar-Driven Chemical Looping Methane Reforming from Redox Cycling of Ceria Porous Foam in a Volumetric Solar Reactor, Chem. Eng. J., vol. 356, pp. 756-770, 2019.10.1016/j.cej.2018.09.072 ↗
8. Du, B. and Zhao, Z., Numerical Prediction of the Spray from an Air-Assisted Fuel Injection System via Eulerian-Lagrangian Approach, Energy Rep., vol. 7, pp. 6718-6732, 2021.10.1016/j.egyr.2021.09.128 ↗
9. Du, B., Zhao, Z., Yang, Z., and Wang, S., Experimental Investigation on the Effects of Fuel-Air Mixture Temperature on the Air-Assisted Kerosene Spray Characteristics, Fuel, vol. 324, p. 124487, 2022.10.1016/j.fuel.2022.124487 ↗
10. Enagi, I.I., Al Attab, K.A., and Zainal, Z.A., Liquid Fuels Spray and Combustion Characteristics in a New Micro Gas Turbine Combustion Chamber Design, Int. J. Energy Res., vol. 43, no. 8, pp. 3365-3380, 2019.10.1002/er.4475 ↗
11. Escobar-Vargas, S., Fabris, D., Gonzalez, J.E., Sharma, R., Bash, C., and Ruiz, O.E., Bubble Growth Characterization during Fast Boiling in an Enclosed Geometry, Int. J. Heat Mass Transf., vol. 52, nos. 21-22, pp. 5102-5112, 2009.10.1016/j.ijheatmasstransfer.2009.05.001 ↗
12. Fan, Y., Hashimoto, N., Nishida, H., and Ozawa, Y., Spray Characterization of an Air-Assist Pressure-Swirl Atomizer Injecting High-Viscosity Jatropha Oils, Fuel, vol. 121, pp. 271-283, 2014.10.1016/j.fuel.2013.12.036 ↗
13. Gao, H., Zhang, F., Zhang, Z., Wang, E., and Liu, B., Experimental Investigation on the Spray Characteristic of Air-Assisted Hollow-Cone Gasoline Injector, Appl. Therm. Eng., vol. 151, pp. 354-363, 2019a.10.1016/j.applthermaleng.2019.02.029 ↗
14. Gao, H., Zhang, F., Zhang, Z., Wang, S., and Wu, H., Trajectory Deviation of Target Jet of Air-Assisted Spray under Different Conditions, Fuel, vol. 249, pp. 252-263, 2019b.10.1016/j.fuel.2019.03.112 ↗
15. Guo, H., Ma, X., Li, Y., Liang, S., Wang, Z., Xu, H., and Wang, J., Effect of Flash Boiling on Microscopic and Macroscopic Spray Characteristics in Optical GDI Engine, Fuel, vol. 190, pp. 79-89, 2017.10.1016/j.fuel.2016.11.043 ↗
16. Guo, H., Wang, B., Li, Y., Xu, H., and Wu, Z., Characterizing External Flashing Jet from Single-Hole GDI Injector, Int. J. Heat Mass Transf., vol. 121, pp. 924-932, 2018.10.1016/j.ijheatmasstransfer.2018.01.042 ↗
17. Hu, J., Liu, B., Zhang, C., Gao, H., Zhang, Z., Zhang, F., and Wang, Y., Experimental Study on the Spray Characteristics of an Air-Assisted Fuel Injection System Using Kerosene and Gasoline, Fuel, vol. 235, pp. 782-794, 2019.10.1016/j.fuel.2018.08.083 ↗
18. Jiang, C., Parker, M.C., Butcher, D., Spencer, A., Garner, C.P., and Helie, J., Comparison of Flash Boiling Resistance of Two Injector Designs and the Consequences on Downsized Gasoline Engine Emissions, Appl. Energy, vol. 254, p. 113735, 2019.10.1016/j.apenergy.2019.113735 ↗
19. Joshi, A., Review of Vehicle Engine Efficiency and Emissions, SAE Int. J. Adv. Curr. Practices Mobil., 2020.10.4271/2021-01-0575 ↗
20. Kapusta, A.J., Understanding the Collapse of Flash-Boiling Sprays Formed by Multi-Hole Injectors Operating at Low Injection Pressures, Energy, vol. 247, p. 123388, 2022.10.1016/j.energy.2022.123388 ↗
21. Kawano, D., Ishii, H., Suzuki, H., Goto, Y., Odaka, M., and Senda, J., Numerical Study on Flash-Boiling Spray of Multicomponent Fuel, Heat Transf. Asian Res., vol. 35, no. 5, pp. 369-385, 2006.10.1002/htj.20117 ↗
22. Kourmatzis, A., Pham, P.X., and Masri, A.R., Air Assisted Atomization and Spray Density Characterization of Ethanol and a Range of Biodiesels, Fuel, vol. 108, pp. 758-770, 2013.10.1016/j.fuel.2013.01.069 ↗
23. Kramer, M., Kull, E., and Wensing, M., Flashboiling-Induced Targeting Changes in Gasoline Direct Injection Sprays, Int. J. Engine Res., vol. 17, no. 1, pp. 97-107, 2016.10.1177/1468087415604763 ↗
24. Lefebvre, A.H. and McDonell, V.G., Atomization and Sprays, Boca Raton, FL: Taylor & Francis, 2017.10.1201/9781315120911 ↗
25. Li, X., Li, T., and Xu, M., Effect of Ambient Temperature on Flash-Boiling Spray Characteristics for a Multi-Hole Gasoline Injector, Exp. Fluids, vol. 60, no. 7, 2019a.10.1007/s00348-019-2754-x ↗
26. Li, X., Xu, Q., Qiu, S., Wang, S., Huang, D., and Xu, M., Investigations on the Impact of Phase Change on Single Plume Flash Boiling Radial Expansion and Drop-Sizing Characteristics, Appl. Therm. Eng., vol. 202, p. 117911, 2022.10.1016/j.applthermaleng.2021.117911 ↗
27. Li, X., Yang, S., Li, T., Huang, D., and Xu, M., Investigations on Near-Field Atomization of Flash Boiling Sprays for Gasoline Direct Injection Related Applications, Fuel, vol. 257, p. 116097, 2019b.10.1016/j.fuel.2019.116097 ↗
28. Liu, K., Chen, C., Su, M., Zhou, W., Wang, Q., Oppong, F., Li, L., and Xu, C., Experimental Study of the Macroscopic Characteristics of Methanol Low‐Pressure Injection Spray, Int. J. Energy Res., vol. 46, no. 15, pp. 23259-23272, 2022.10.1002/er.8625 ↗
29. Liu, R., Wei, M., and Yang, H., Cold Start Control Strategy for a Two-Stroke Spark Ignition Diesel-Fuelled Engine with Air-Assisted Direct Injection, Appl. Therm. Eng., vol. 108, pp. 414-426, 2016.10.1016/j.applthermaleng.2016.07.148 ↗
30. Liu, X., Hong, H., Zhang, H., Cao, Y., Qu, W., and Jin, H., Solar Methanol by Hybridizing Natural Gas Chemical Looping Reforming with Solar Heat, Appl. Energy, vol. 277, p. 115521, 2020.10.1016/j.apenergy.2020.115521 ↗
31. Mehrpooya, M., Ghorbani, B., Shahsavari, A., and Zaitsev, A., Conversion and Storage of Solar Energy in the Forms of Liquid Fuel and Electricity in a Hybrid Energy Storage System Using Methanol and Phase Change Materials, Energy Conv. Manag., vol. 209, p. 112669, 2020.10.1016/j.enconman.2020.112669 ↗
32. Sher, E., Bar-Kohany, T., and Rashkovan, A., Flash-Boiling Atomization, Prog. Energy Combust. Sci., vol. 34, no. 4, pp. 417-439, 2008.10.1016/j.pecs.2007.05.001 ↗
33. Shih, C.F., Zhang, T., Li, J., and Bai, C., Powering the Future with Liquid Sunshine, Joule, vol. 2, no. 10, pp. 1925-1949, 2018.10.1016/j.joule.2018.08.016 ↗
34. Spiteri, A., Dimopoulos Eggenschwiler, P., Liao, Y., Wigley, G., Michalow-Mauke, K.A., Elsener, M., Krocher, O., and Boulouchos, K., Comparative Analysis on the Performance of Pressure and Air-Assisted Urea Injection for Selective Catalytic Reduction of Nox, Fuel, vol. 161, pp. 269-277, 2015.10.1016/j.fuel.2015.08.061 ↗
35. Wang, F., Swinbourn, R., and Li, C., Shipping Australian Sunshine: Liquid Renewable Green Fuel Export, Int. J. Hydrogen Energy, 2023.10.1016/j.ijhydene.2022.12.326 ↗
36. Wu, H., Wang, L., Wu, L., Wu, Y., Sun, B., Zhao, Z., and Liu, F., Spray Performance of Air-Assisted Kerosene Injection in a Constant Volume Chamber under Various In-Cylinder GDI Engine Conditions, Appl. Therm. Eng., vol. 150, pp. 762-769, 2019.10.1016/j.applthermaleng.2019.01.014 ↗
37. Wu, H., Zhang, F., Zhang, Z., Guo, Z., Zhang, W., and Gao, H., On the Role of Vortex-Ring Formation in Influencing Air-Assisted Spray Characteristics of n-Heptane, Fuel, vol. 266, p. 117044, 2020.10.1016/j.fuel.2020.117044 ↗
38. Wu, H., Zhang, F., and Zhang, Z., Fundamental Spray Characteristics of Air-Assisted Injection System Using Aviation Kerosene, Fuel, vol. 286, pp. 119420, 2021.10.1016/j.fuel.2020.119420 ↗
39. Xu, Q., Sun, Z., Wang, S., Fan, Y., Li, X., and Xu, M., A Morphological Study of Supercritical Fuel Flash-Boiling Spray, Fuel, vol. 310, pp. 122365, 2022.10.1016/j.fuel.2021.122365 ↗
40. Yang, S., Li, X., Huang, D., and Xu, M., Characteristics and Correlation of Nozzle Internal Flow and Jet Breakup under Flash Boiling Conditions, Int. J. Heat Mass Transf., vol. 127, pp. 959-969, 2018.10.1016/j.ijheatmasstransfer.2018.07.109 ↗
41. Zeng, W., Xu, M., Zhang, G., Zhang, Y., and Cleary, D.J., Atomization and Vaporization for Flash-Boiling Multi-Hole Sprays with Alcohol Fuels, Fuel, vol. 95, pp. 287-297, 2012.10.1016/j.fuel.2011.08.048 ↗
42. Zhai, S., Jiang, S., Liu, C., Li, Z., Yu, T., Sun, L., Ren, G., and Deng, W., Liquid Sunshine: Formic Acid, J. Phys. Chem. Lett., vol. 13, no. 36, pp. 8586-8600, 2022.10.1021/acs.jpclett.2c02149 ↗
43. Zhang, Z. and Zhang, P., Kinetic Energy Recovery and Interface Hysteresis of Bouncing Droplets after Inelastic Head-On Collision, Phys. Fluids, vol. 29, no. 10, p. 103306, 2017.10.1063/1.5000547 ↗
44. Zhao, W., Yan, J., Guo, S., Lee, T.H., and Li, X., Effects of Fuel Properties and Aerodynamic Breakup on Spray under Flash Boiling Conditions, Appl. Therm. Eng., vol. 200, p. 117646, 2022.10.1016/j.applthermaleng.2021.117646 ↗
45. Zheng, J., Zhou, H., Wang, C., Ye, E., Xu, J.W., Loh, X.J., and Li, Z., Current Research Progress and Perspectives on Liquid Hydrogen Rich Molecules in Sustainable Hydrogen Storage, Energy Storage Mater., vol. 35, pp. 695-722, 2021.10.1016/j.ensm.2020.12.007 ↗