MERGING CONICAL LIQUID SHEETS FROM COAXIAL PRESSURE-SWIRL INJECTORS
Source abstract
Abstract
The conditions for merging two liquid sheets in a coaxial pressure-swirl external mixing injector were assessed experimentally and numerically. Fast imaging was employed based on the backlighting technique to experimentally investigate the behavior of the exit liquid sheet. The simulation was also carried out using a volume of fluid model considering two-dimensional axisymmetric swirl conditions. Performance characteristics including discharge coefficient, sheet angle, and sheet pattern at different injection pressures were assessed experimentally and by simulation for separate and simultaneous spraying conditions. To study the merging condition, the gas phase pressure field just downstream of the injector exit was numerically investigated separate and simultaneous results show that the lowest gas pressure occurs in the region inside the liquid cone produced. The larger the diameter of the injector outlet, the greater the volume of the hollow cone and the smaller the amount of this vacuum. When the internal and external injectors worked simultaneously, three areas were distinguished: the inner space of the internal injector, the space between the two liquid sheets, and the outer space of the external injector. The largest pressure gradients in the gas pressure occurred in the space between the two liquid sheets. By increasing the injection pressure of the external injector, the static pressure between the two sheets decreased and reached the pressure required to merge the two sheets, thus, the two liquid sheets can merge.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Fluid Dynamics and Heat Transfer · Combustion and flame dynamics · Electrohydrodynamics and Fluid Dynamics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (25)
Show source-provided references
1. ANSYS, Fluent Theory Guide, Release 18.2, 15317 (November), 2013.
2. Baran, O., Ozyoruk, Y., and Sumer, B., Experimental and Numerical Investigation of Coaxial Pressure Swirl Injectors, A/AA Scitech. Conf., San Diego, CA, p. 1740, 2019.10.2514/6.2019-1740 ↗
3. Ding, J.-W., Li, G.-X., and Yu, Y.-S., The Instability and Droplet Size Distribution of Liquid-Liquid Coaxial Swirling Spray: An Experimental Investigation, Exp. Therm. Fluid Sci., vol. 82, pp. 166-173, 2017.10.1016/j.expthermflusci.2016.11.014 ↗
4. Donjat, D., Estivalezes, J., and Michau, M., A Description of the Pressure Swirl Atomizer Internal Flow, ASME 2002 Joint U.S.-European Fluids Engineering Division. Conf., Quebec, Canada, vol. 1, pp. 439-444, 2022.10.1115/FEDSM2002-31017 ↗
5. Farhangi, S., Yu, T., Rojas, L., Sprouse, K., and Mckinnon, J., Gas-Gas Injector Technology for Full Flow Stage Combustion Cycle Application, Proc. of the 35th Intl. Joint Propulsion Conf., Los Angeles, CA, p. 2757, 1999.10.2514/6.1999-2757 ↗
6. Habiballah, M., Vingert, L., Duthoit, V., and Vuillermoz, P., Research as a Key in the Design Methodology of Liquid-Propellant Combustion Devices, J. Propuls. Power, vol. 14, no. 5, pp. 782-788, 1998.10.2514/2.5341 ↗
7. Isa, K.M., Osman, K., Yahya, A., Ghaffar, Z.A., Hamid, A.H.A., and Kasolang, S., Studies on the Spray Characteristics of Pressure-Swirl Atomizers for Automatic Hand Sanitizer Application, J. Adv.Res. Fluid Mech. Therm. Sci., vol. 55, no. 1, pp. 51-64, 2019.
8. Kim, D., Han, P., Im, J.-H., Yoon, Y., and Bazarov, V.-G., Effect of Recess on the Spray Characteristics of Liquid-Liquid Swirl Coaxial Injectors, J. Propuls. Power, vol. 23, no. 6, pp. 1194-1203, 2007.10.2514/1.30450 ↗
9. Lefebvre, A.H. and Mcdonell, V.G., Atomization and Sprays, Boca Raton, FL: CRC Press, 2017.10.1201/9781315120911 ↗
10. Liu, J., Zhang, X.-Q., Li, Q.-L., and Wang, Z.-G., Effect of Geometric Parameters on the Spray Cone Angle in the Pressure Swirl Injector, Proc. Inst. Mech. Eng. Part G: J. Aerospace Eng., vol. 227, no. 2, pp. 342-353, 2013.10.1177/0954410011432233 ↗
11. Madsen, J., Hjertager, B.H., and Solberg, T., Numerical Simulation of Internal Flow in a Large-Scale Pressure-Swirl Atomizer, Proc. of the 19th Intl. on Liquid Atomization and Spray Systems Conf., Nottingham, UK, 2004.
12. Mangra, A.C., Florean, F., Enache, M., and Kunscer, R., Design, Experimental and Numerical Investigation of Coaxial Swirl Injector, Atomization Sprays, vol. 32, no. 12, pp. 72-75, 2022.10.1615/AtomizSpr.2022041454 ↗
13. Popp, M., Hulka, J., Yang, V., and Habiballah, M., Liquid Rocket Thrust Chambers: Aspects of Modeling, Analysis, and Design, Reston, VA: American Institute of Aeronautics and Astronautics, 2004.10.2514/4.866760 ↗
14. Rivas, J.R.R., Pimenta, A.P., Salcedo, S.G., Rivas, G.A.R., and Suazo, M.C.G., Study of Internal Flow of a Bipropellant Swirl Injector of a Rocket Engine, J. Braz. Soc. Mech. Sci. Eng., vol. 40, no. 6, pp. 1-16, 2018.10.1007/s40430-018-1205-6 ↗
15. Shi, Z., Wang, X., and Chen, Q., Numerical Simulation on Atomizing Performance of Pressure Swirl Nozzles in Ethoxylation Reactors, Int. J. Chem. React. Eng., vol. 16, no. 2, p. 20170028, 2018.10.1515/ijcre-2017-0028 ↗
16. Sivakumar, D. and Raghunandan, B., Jet Interaction in Liquid-Liquid Coaxial Injectors, Fluids Eng., vol. 118, pp. 329-334, 1996.10.1115/1.2817381 ↗
17. Sivakumar, D. and Raghunandan, B., Formation and Separation of Merged Liquid Sheets Developed from the Mixing of Coaxial Swirling Liquid Sheets, Phys. Fluids, vol. 15, no. 11, pp. 3443-3451, 2003.10.1063/1.1616032 ↗
18. Sivakumar, D. and Raghunandan, B., Hysteretic Interaction of Conical Liquid Sheets from Coaxial Atomizers: Influence on the Spray Characteristics, Phys. Fluids, vol. 10, no. 6, pp. 1384-1397, 1998.10.1063/1.869663 ↗
19. Som, S., Air Core in Pressure Swirl Atomizing Nozzles, Atomization Sprays, vol. 22, no. 4, pp. 283-303, 2012.10.1615/AtomizSpr.2012005174 ↗
20. Sumer, B., Erkan, N., Uzol, O., and Tuncer, I.H., Experimental and Numerical Investigation of a Pressure Swirl Atomizer, Proc. of the 12th Intl. on Liquid Atomization and Spray Systems Conf., Heidelberg, Germany, 2012.
21. Sun, L., Huang, Y., and Liu, Z., Improved Semi-Empirical Prediction of Viscous Spray Cone Angle for Pressure Swirl Atomizers, Atomization Sprays, vol. 27, no. 9, pp. 771-790, 2017.10.1615/AtomizSpr.2017019727 ↗
22. Sreelakshmi, T. and Chilanna, N., A Numerical Study of Spray Characteristics of a Pressure Swirl Atomizer, Int. J. Innov. Eng. Res. Technol., vol. 4, no. 6, pp. 1-7, 2017.
23. Wang, X. and Yang, V., Supercritical Mixing and Combustion of Liquid-Oxygen/Kerosene Bi-Swirl Injectors, J. Propuls. Power, vol. 33, no. 2, pp. 316-322, 2017.10.2514/1.B36262 ↗
24. Wilcox, D.C., Turbulence Modeling for CFD, La Canada, CA: DCW Industries, 1998.
25. Yoon,W. and Ahn, K., Experimental and Theoretical Study on Spray Angles of Bi-Swirl Coaxial Injectors, J. Appl. Fluid Mech., vol. 11, no. 5, pp. 1377-1386, 2018.10.29252/jafm.11.05.28814 ↗