The thermal stability of nanobainitic microstructure and its effect on the mechanical properties of a high-carbon steel manufactured by the thermomechanical treatment
Source abstract
Abstract
Abstract The present study investigates the effect of tempering on the microstructural evolution and mechanical properties of a nanostructured bainitic steel produced through a novel thermomechanical treatment. In this study, tempering was applied to separately prepared specimens to reproduce the thermal exposure associated with the anticipated service conditions of the steel, rather than as part of its conventional heat-treatment route. Tempering was carried out at temperatures ranging from 150 °C to 600°C for 2 h to evaluate the stability and transformation behavior of the nanobainitic microstructure. A combination of synchrotron X-ray diffraction, dilatometric analysis, scanning electron microscopy observation, and mechanical testing was employed to investigate the structural changes and their influence on strength and ductility. At lower tempering temperatures (150–360 °C and 450 °C), microstructural changes were primarily determined by carbon diffusion within the bainitic ferrite and retained austenite. This led to a decrease in the volume fraction of the retained austenite and an increase in the volume fraction of the bainitic ferrite. Additionally, these temperatures promoted the precipitation of ε-carbides and cementite, as well as bainitic transformation during tempering and martensitic transformation during cooling. At elevated temperatures (500–600 °C), the decomposition of retained austenite into ferrite and cementite, indicating further carbon redistribution and phase transformation. The ultimate tensile strength (UTS) and yield strength (YS) of tempered specimens were lower than those of the untempered condition. However, a substantial increase in YS was observed at 450 °C, surpassing the untempered value by 131 MPa. This phenomenon is presumably attributable to the impeding of dislocation motion by interfacial cementite precipitation.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (59)
Show source-provided references
1. Caballero FG, Bhadeshia HKDH, Mawella KJA, Jones DG. Brown. Very strong low temperature bainite. Mater Sci Technol. 2002;18:279–84. https://doi.org/10.1179/026708301225000725.10.1179/026708301225000725 ↗
2. Janus K, Maziarz W, Korpala G, Chulist R, Jarzębska A, Bala P, Dziurka R, Prahl U, Rogal L. Influence of microstructure on the mechanical properties and work-hardening behavior of high-carbon nanostructured bainitic steel. Arch Metall Mater. 2025;70:477–88. https://doi.org/10.24425/amm.2025.152568.10.24425/amm.2025.152568 ↗
3. Garcia-Mateo C, Caballero FG, Sourmail T, Kuntz M, Cornide J, Smanio V, Elvira R. Tensile behaviour of a nanocrystalline bainitic steel containing 3wt% silicon. Mater Sci Engineering: A. 2012;549:185–92. https://doi.org/10.1016/j.msea.2012.04.031.10.1016/j.msea.2012.04.031 ↗
4. Morales-Rivas L, Garcia-Mateo C, Sourmail T, Kuntz M, Rementeria R, Caballero FG. Ductility of nanostructured bainite. Metals. 2016;6:302. https://doi.org/10.3390/met6120302.10.3390/met6120302 ↗
5. Morales-Rivas L, Archie F, Zaefferer S, Benito-Alfonso M, Tsai S-P, Yang J-R, Raabe D, Garcia-Mateo C, Caballero FG. Crystallographic examination of the interaction between texture evolution, mechanically induced martensitic transformation and twinning in nanostructured bainite. J Alloys Compd. 2018;752:505–19. https://doi.org/10.1016/j.jallcom.2018.04.189.10.1016/j.jallcom.2018.04.189 ↗
6. Kumar A, Singh A. Mechanical properties of nanostructured bainitic steels. Materialia. 2021;15:101034. https://doi.org/10.1016/j.mtla.2021.101034.10.1016/j.mtla.2021.101034 ↗
7. Lee S-I, Lee J-M, Kim S-G, Song Y-B, Kim H-K, Shim J-H, Hwang B. Influence of austempering temperature on microstructure and mechanical properties of high-carbon nanostructured bainitic steels. Mater Sci Engineering: A. 2022;848:143334. https://doi.org/10.1016/j.msea.2022.143334.10.1016/j.msea.2022.143334 ↗
8. Garcia-Mateo C, Caballero FG, Bhadeshia HKDH. Development of hard bainite. ISIJ Int. 2003;43:1238–43. https://doi.org/10.2355/isijinternational.43.1238.10.2355/isijinternational.43.1238 ↗
9. Timokhina IB, Beladi H, Xiong XY, Adachi Y, Hodgson PD. Nanoscale microstructural characterization of a nanobainitic steel. Acta Mater. 2011;59:5511–22. https://doi.org/10.1016/j.actamat.2011.05.027.10.1016/j.actamat.2011.05.027 ↗
10. Bhadeshia HKDH. Materials algorithms project. Available from: http://www.msm.cam.ac.uk/map/steel/programs/mucg83.html
11. Amel-Farzad H, Faridi HR, Rajabpour F, Abolhasani A, Kazemi S, Khaledzadeh Y. Developing very hard nanostructured bainitic steel. Mater Sci Engineering: A. 2013;559:68–73. https://doi.org/10.1016/j.msea.2012.08.114.10.1016/j.msea.2012.08.114 ↗
12. Bhadeshia HKDH. Bainite in Steel: Theory and Practice. 3rd ed. London: Institute of Materials, Minerals & Mining; 2015. pp. 208–36.
13. Jiang T, Liu HJ, Sun JJ, Guo SW, Liu YN. Effect of austenite grain size on transformation of nanobainite and its mechanical properties. Mater Sci Engineering: A. 2016;666:207–13. https://doi.org/10.1016/j.msea.2016.04.041.10.1016/j.msea.2016.04.041 ↗
14. Gong W, Tomota Y, Harjo S, Su YH, Aizawa K. Effect of prior martensite on bainite transformation in nanobainite steel. Acta Mater. 2015;85:243–9. https://doi.org/10.1016/j.actamat.2014.11.028.10.1016/j.actamat.2014.11.028 ↗
15. Eres-Castellanos A, Garcia-Mateo C, Caballero FG. Future trends on displacive stress and strain induced transformations in steels. Metals. 2021;11:299. https://doi.org/10.3390/met11020299.10.3390/met11020299 ↗
16. Mousalou H, Yazdani S, Avishan B, Ahmadi NP, Chabok A, Pei Y. Microstructural and mechanical properties of low-carbon ultra-fine bainitic steel produced by multi-step austempering process. Mater Sci Engineering: A. 2018;734:329–37. https://doi.org/10.1016/j.msea.2018.08.008.10.1016/j.msea.2018.08.008 ↗
17. Fan H, Zhao A, Li Q, Guo H, He J. Effects of ausforming strain on bainite transformation in nanostructured bainite steel. Int J Min Metall Mater. 2017;24(3):264–70. https://doi.org/10.1007/s12613-017-1404-7.10.1007/s12613-017-1404-7 ↗
18. Janus K, Rogal L, Dutkiewicz J, Chulist R, Korpala G, Prahl U, Konczak K, Kochmanski P, Nalepka K, Maziarz W. Effect of a novel controlled thermomechanical treatment on the microstructure and mechanical properties of a high-carbon nanobainitic steel. Archives Civil Mech Eng. 2023;23:252. https://doi.org/10.1007/s43452-023-00791-8.10.1007/s43452-023-00791-8 ↗
19. Guo H, Li Q, Fan Y, Feng X. Bainite transformation behavior, microstructural feature and mechanical properties of nanostructured bainitic steel subjected to ausforming with different strain. J Mater Res Technol. 2020;9:9206–18. https://doi.org/10.1016/j.jmrt.2020.06.090.10.1016/j.jmrt.2020.06.090 ↗
20. Królicka A, Żak AM, Caballero FG. Enhancing technological prospect of nanostructured bainitic steels by the control of thermal stability of austenite. Mater Design. 2021;202:109551. https://doi.org/10.1016/j.matdes.2021.110143.10.1016/j.matdes.2021.110143 ↗
21. Kang J, Zhang FC, Yang XW, Lv B, Wu KM. Effect of tempering on the microstructure and mechanical properties of a medium carbon bainitic steel. Mater Sci Engineering: A. 2017;688:238–45. https://doi.org/10.1016/j.msea.2017.01.044.10.1016/j.msea.2017.01.044 ↗
22. Peet MJ, Babu SS, Miller MK, Bhadeshia HKDH. Tempering of low-temperature bainite. Metall Mater Trans A. 2017;48:3410–8. https://doi.org/10.1007/s11661-017-4086-x.10.1007/s11661-017-4086-x ↗
23. Santajuana MA, Rementeria R, Kuntz M, Jimenez JA, Caballero FG, Garcia-Mateo C. Low-temperature bainite: a thermal stability study. Metall Mater Trans A. 2018;49:2026–36. https://doi.org/10.1007/s11661-018-4595-2.10.1007/s11661-018-4595-2 ↗
24. Zhou M, Xu G, Hu H, Yuan Q, Tian J. The effect of large stress on bainitic transformation at different transformation temperatures. Steel Res Int. 2017;88:1600377. https://doi.org/10.1002/srin.201600377.10.1002/srin.201600377 ↗
25. Sourmail T, Otter L, Collin S, Billet M, Philippot A, Cristofari F, Secordel P. Direct and indirect decomposition of retained austenite in continuously cooled bainitic steels: influence of vanadium. Mater Charact. 2021;173:110922. https://doi.org/10.1016/j.matchar.2021.110922.10.1016/j.matchar.2021.110922 ↗
26. Ruiz-Jimenez V, Kuntz M, Sourmail T, Caballero FG, Jimenez JA. Garcia-Mateo. Retained austenite destabilization during tempering of low-temperature bainite. Appl Sci. 2020;10:8901. https://doi.org/10.3390/app10248901.10.3390/app10248901 ↗
27. Rogal L, Dutkiewicz J. Effect of annealing on microstructure, phase composition and mechanical properties of thixo-cast 100Cr6 steel. Mater Charact. 2012;68:123–30. https://doi.org/10.1016/j.matchar.2012.03.018.10.1016/j.matchar.2012.03.018 ↗
28. Tolouei E, Hurel V, Loucif A, et al. Influence of the as-quenched state and tempering heating rate on microstructural characteristics of a high-strength steel. Metall Mater Trans A. 2025;56:2189–201. https://doi.org/10.1007/s11661-025-07778-5.10.1007/s11661-025-07778-5 ↗
29. Wang X, Liu C, Qin Y, Li Y, Yang Z, Long X, Wang M, Zhang F. Effect of tempering temperature on microstructure and mechanical properties of nanostructured bainitic steel. Mater Sci Engineering: A. 2022;832:142357. https://doi.org/10.1016/j.msea.2021.142357.10.1016/j.msea.2021.142357 ↗
30. Allain SYP, Aoued S, Quintin-Poulon A, Gouné M, Danoix F, Hell J-C, Bouzat M, Soler M. Geandier. In situ investigation of the iron carbide precipitation process in a Fe-C-Mn-Si Q&P steel. Materials. 2018;11:1087. https://doi.org/10.3390/ma11071087.10.3390/ma11071087 ↗
31. Podder AS. Tempering of a mixture of bainite and retained austenite. PhD Thesis, University of Cambridge, 2011.
32. Caballero FG, García-Mateo C, Chao J, Santofimia MJ, Capdevila C. García de Andrés. Effects of Morphology and Stability of Retained Austenite on the Ductility of TRIP-aided Bainitic Steels. ISIJ Int. 2008;48:1256–62. https://doi.org/10.2355/isijinternational.48.1256.10.2355/isijinternational.48.1256 ↗
33. García-Mateo C, Caballero FG. The Role of Retained Austenite on Tensile Properties of Steels with Bainitic Microstructures. Mater Trans. 2005;46:1839–46. https://doi.org/10.2320/matertrans.46.1839.10.2320/matertrans.46.1839 ↗
34. Brown CS, Speer JG, De Moor E. Influence of retained austenite on abrasive wear performance of bainitic steels. Wear (2023), 204720. https://doi.org/10.1016/j.wear.2023.20472010.1016/j.wear.2023.204720 ↗
35. Mola J, Seo EJ, Cho L. Correlation between mechanical stability and hardness of austenite in martensite/austenite mixtures. Mater Sci Engineering: A. 2021;822:141687. https://doi.org/10.1016/j.msea.2021.141687.10.1016/j.msea.2021.141687 ↗
36. Dudko V, Yuzbekova D, Gaidar S, Vetrova S, Kaibyshev R. Tempering behavior of novel low-alloy high-strength steel. Metals. 2022;12:2177. https://doi.org/10.3390/met12122177.10.3390/met12122177 ↗
37. Caballero FG, Miller MK, Garcia-Mateo C. Carbon supersaturation of ferrite in a nanocrystalline bainitic steel. Acta Mater. 2010;58:2338–43. https://doi.org/10.1016/j.actamat.2009.12.020.10.1016/j.actamat.2009.12.020 ↗
38. Garcia-Mateo C, Jiménez JA, Yen HW, Miller MK, Morales-Rivas L, Kuntz M, Caballero FG. Low temperature bainitic ferrite: Evidence of carbon super-saturation and tetragonality. Acta Mater. 2015;91:162–73. https://doi.org/10.1016/j.actamat.2015.03.018.10.1016/j.actamat.2015.03.018 ↗
39. Avishan B, Garcia-Mateo C, Yazdani S, Caballero FG. Retained austenite thermal stability in a nanostructured bainitic steel. Mater Charact. 2013;81:105–10. https://doi.org/10.1016/j.matchar.2013.04.015.10.1016/j.matchar.2013.04.015 ↗
40. Cao Y, Wang ZD, Kang J, Wu D, Wang GD. Effects of tempering temperature and Mo/Ni on microstructures and properties of lath martensitic wear-resistant steels. J Iron Steel Res Int. 2013;20:70–5. https://doi.org/10.1016/S1006-706X(13)60085-0.10.1016/S1006-706X(13)60085-0 ↗
41. Caballero FG, Miller MK, Garcia-Mateo C. Atom probe tomography analysis of precipitation during tempering of a nanostructured bainitic steel. Metall Mater Trans A. 2011;42:3660–8. https://doi.org/10.1007/s11661-011-0699-7.10.1007/s11661-011-0699-7 ↗
42. Caballero FG, Miller MK, Garcia-Mateo C, Capdevila C, Babu SS. Redistribution of alloying elements during tempering of a nanocrystalline steel. Acta Mater. 2008;56:188–99. https://doi.org/10.1016/j.actamat.2007.09.018.10.1016/j.actamat.2007.09.018 ↗
43. Podder AS, Lonardelli I, Molinari A, Bhadeshia HKDH. Thermal stability of retained austenite in bainitic steel: an in situ study. Proc Royal Soc A. 2011;467:3141–56. https://doi.org/10.1098/rspa.2011.0212.10.1098/rspa.2011.0212 ↗
44. Cheng L, Brakman CM, Korevaar BM, Mittemeijer EJ. The tempering of iron-carbon martensite; dilatometric and calorimetric analysis. Metall Trans A. 1988;19:2415–26. https://doi.org/10.1007/BF02645469.10.1007/BF02645469 ↗
45. Zorgani M, Garcia-Mateo C, Jahazi M. Microstructural evolution during tempering of an ausformed carbide-free low temperature bainitic steel. Mater Design. 2021;210:110082. https://doi.org/10.1016/j.matdes.2021.110082.10.1016/j.matdes.2021.110082 ↗
46. Park HS, Seol JB, Lim NS, Kim SI, Park CG. Study of the decomposition behavior of retained austenite and the partitioning of alloying elements during tempering in CMnSiAl TRIP steels. Mater Design. 2015;82:173–80. https://doi.org/10.1016/j.matdes.2015.05.059.10.1016/j.matdes.2015.05.059 ↗
47. Cermak J, Kral L. Carbon diffusion in carbon-supersaturated ferrite and austenite. J Alloys Compd. 2014;586:129–35. https://doi.org/10.1016/j.jallcom.2013.10.058.10.1016/j.jallcom.2013.10.058 ↗
48. Primig S, Leitner H. Separation of overlapping retained austenite decomposition and cementite precipitation reactions during tempering of martensitic steel by means of thermal analysis. Thermochimica acta. 2011;526:111–7. https://doi.org/10.1016/j.tca.2011.09.001.10.1016/j.tca.2011.09.001 ↗
49. Talebi SH, Jahazi M, Melkonyan H. Retained austenite decomposition and carbide precipitation during isothermal tempering of a medium-carbon low-alloy bainitic steel. Materials. 2018;11:1441. https://doi.org/10.3390/ma11081441.10.3390/ma11081441 ↗
50. Wu YX, Sun WW, Gao X, Styles MJ, Arlazarov A, Hutchinson CR. The effect of alloying elements on cementite coarsening during martensite tempering. Acta Mater. 2020;183:418–37. https://doi.org/10.1016/j.actamat.2019.11.040.10.1016/j.actamat.2019.11.040 ↗
51. Forsik SA, P.E. Rivera-Diaz-del-Castillo. Martensitic steels: epsilon carbides in tempered. Encyclopedia of Iron, Steel, and, Alloys T. CRC Press, Boca Raton, FL, USA (2016) 2169–2181. https://doi.org/10.1081/E-EISA-12005202610.1081/E-EISA-120052026 ↗
52. Xiong Z, Timokhina I. Pereloma. Clustering, nano-scale precipitation and strengthening of steels. Prog Mater Sci. 2021;118:100764. https://doi.org/10.1016/j.pmatsci.2020.100764.10.1016/j.pmatsci.2020.100764 ↗
53. Fedoseeva A, Dudova N, Kaibyshev R. Creep strength breakdown and microstructure evolution in a 3% Co modified P92 steel. Mater Sci Engineering: A. 2016;654:1–12. https://doi.org/10.1016/j.msea.2015.12.027.10.1016/j.msea.2015.12.027 ↗
54. Wang X, Zhang X, Fang Q, Ma H, Zhang R, Liu F, Zhang F. Effect of tempering on stability of retained austenite and tensile properties of nanostructured bainitic steel. Mater Sci Engineering: A. 2022;856:143958. https://doi.org/10.1016/j.msea.2022.143958.10.1016/j.msea.2022.143958 ↗
55. Królicka A, Caballero FG, Kuziak R, Radwański K, Sozańska-Jędrasik L, Stawarczyk P. Two design strategies for enhancing the thermal stability of bainitic structures. J Mater Res Technol. 2023;24:7004–20. https://doi.org/10.1016/j.jmrt.2023.05.003.10.1016/j.jmrt.2023.05.003 ↗
56. Chen CY, Chen CC, Lin JS. Morphology feature of nanostructure bainitic steel after tempering treatment. Int J Mech Industrial Sci Eng. 2014;8:876–9.
57. Hasan HS, Peet MJ, Bhadeshia HKDH. Severe tempering of bainite generated at low transformation temperatures. Int J Mater Res. 2012;103:1319–24. https://doi.org/10.3139/146.110788.10.3139/146.110788 ↗
58. Bhadeshia HKDH, Honeycombe RWK. Steels: Microstructure and Properties. 3rd ed. Oxford: Butterworth-Heinemann; 2006.
59. Haiko O, Kaijalainen A, Pallaspuro S, Hannula J, Porter D, Liimatainen T, Kömi J. The effect of tempering on the microstructure and mechanical properties of a novel 0.4 C press-hardening steel. Appl Sci. 2019;9:4231. https://doi.org/10.3390/app9204231.10.3390/app9204231 ↗