Influence of textures on cutting tool tribology in dry machining of super duplex stainless steel
Source abstract
Abstract
Abstract Flank face surface texturing has proven to be an effective approach to improve tool wear resistance, yet the impact of texture shape on flank wear remains insufficiently explored. This research examines the performance of dimple-, groove-, and wave-textured flank faces during dry turning of super duplex stainless steel SDSS 2507. Tool performance was assessed through flank wear measurements, SEM–EDX analysis of wear mechanisms, and chip morphology evaluation under different cutting conditions. All textured inserts demonstrated superior wear resistance compared to non-textured tools, with minimum flank wear values of 80 μm, 69 μm, and 65 μm for dimple, groove, and wave-textured tools, respectively, observed at a cutting speed (v c ) of 125 m/min, feed rate (f r ) of 0.12 mm/rev, and depth of cut (d c ) of 0.4 mm. At lower cutting parameters, adhesion-dominated wear prevailed, where dimple-textured tools exhibited slightly lower flank wear, while groove- and wave-textured tools displayed comparable performance. With increasing cutting speed and feed rate, abrasive wear became dominant, and groove- and wave-textured tools outperformed dimple-textured tools probably due to improved debris evacuation, enhanced heat dissipation, and more uniform stress distribution along the flank face. SEM–EDX and chip morphology analyses supported these observations. Taguchi-based S/N ratio analysis identified the wave texture with v c = 125 m/min, f r = 0.12 mm/rev, and d c = 0.4 mm as the optimal parameter combination for the lowest flank wear. The findings highlight the critical role of flank face texture geometry in controlling wear mechanisms and enhancing machining performance for difficult-to-machine materials under dry conditions.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced machining processes and optimization · Advanced Surface Polishing Techniques · Erosion and Abrasive Machining
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. Mativenga P, Schoop J, Jawahir IS, Biermann D, Kipp M, Kilic ZM, et al. Engineered design of cutting tool material, geometry, and coating for optimal performance and customized applications: a review. CIRP J Manuf Sci Technol. 2024;52:212–28. https://doi.org/10.1016/j.cirpj.2024.06.001.10.1016/j.cirpj.2024.06.001 ↗
2. Siju AS, Gajrani KK, Joshi SS. Dual textured carbide tools for dry machining of titanium alloys. Int J Refract Met Hard Mater. 2021;94:105403. https://doi.org/10.1016/j.ijrmhm.2020.105403.10.1016/j.ijrmhm.2020.105403 ↗
3. Bayraktar S. Dry cutting: A sustainable machining technology. INC.; 2021. https://doi.org/10.1016/B978-0-12-818115-7.00004-3.10.1016/B978-0-12-818115-7.00004-3 ↗
4. Ma J, Duong NH, Lei S. Numerical investigation of the performance of microbump textured cutting tool in dry machining of AISI 1045 steel. J Manuf Process. 2015;19:194–204. https://doi.org/10.1016/j.jmapro.2014.10.001.10.1016/j.jmapro.2014.10.001 ↗
5. Roushan A, Chetan. Effect of discrete and continuous texture geometries on tool wear and derivative cutting effect during the machining. Wear. 2025;568–9. https://doi.org/10.1016/j.wear.2025.205964.10.1016/j.wear.2025.205964 ↗
6. Xing Y, Deng J, Zhao J, Zhang G, Zhang K. Cutting performance and wear mechanism of nanoscale and microscale textured Al2O3/TiC ceramic tools in dry cutting of hardened steel. Int J Refract Met Hard Mater. 2014;43:46–58. https://doi.org/10.1016/j.ijrmhm.2013.10.019.10.1016/j.ijrmhm.2013.10.019 ↗
7. Arslan A, Masjuki HH, Kalam MA, Varman M, Mufti RA, Mosarof MH, et al. Surface texture manufacturing techniques and tribological effect of surface texturing on cutting tool performance: a review. Crit Rev Solid State Mater Sci. 2016;41:447–81. https://doi.org/10.1080/10408436.2016.1186597.10.1080/10408436.2016.1186597 ↗
8. Mishra SK, Ghosh S, Aravindan S. 3D finite element investigations on textured tools with different geometrical shapes for dry machining of titanium alloys. Int J Mech Sci. 2018;141:424–49. https://doi.org/10.1016/j.ijmecsci.2018.04.011.10.1016/j.ijmecsci.2018.04.011 ↗
9. Özel T, Biermann D, Enomoto T, Mativenga P. Structured and textured cutting tool surfaces for machining applications. CIRP Ann. 2021;70:495–518. https://doi.org/10.1016/j.cirp.2021.05.006.10.1016/j.cirp.2021.05.006 ↗
10. Rajbongshi SK, Annebushan Singh M, Kumar Sarma D. A comparative study in machining of AISI D2 steel using textured and non-textured coated carbide tool at the flank face. J Manuf Process. 2018;36:360–72. https://doi.org/10.1016/j.jmapro.2018.10.041.10.1016/j.jmapro.2018.10.041 ↗
11. George A, Dhanish PB, Mathew J. Sustainable Machining of KhN67VMTYu Using Textured Tools: Insights into Tool Wear, Forces, and Surface Roughness Analysis. J Mater Eng Perform. 2025. https://doi.org/10.1007/s11665-025-11554-2.10.1007/s11665-025-11554-2 ↗
12. Rajurkar A, Chinchanikar S. Investigations on homothetic and hybrid micro-textured tools during turning Inconel-718. Mater Manuf Process. 2024;39:529–45. https://doi.org/10.1080/10426914.2023.2236188.10.1080/10426914.2023.2236188 ↗
13. Chen A, Yang F, Jiang F, Li J, Li G, Wang X. Investigation on tribological properties of leaf-vein-inspired bionic textures on cemented carbide tool surfaces. Tribol Int. 2026;214:111204. https://doi.org/10.1016/j.triboint.2025.111204.10.1016/j.triboint.2025.111204 ↗
14. Rajbongshi SK, Sarma DK. Performance parameters studies in machining of AISI D2 steel with dot-textured, groove-textured & non-textured cutting tool at the flank face. Int J Refract Met Hard Mater. 2019. https://doi.org/10.1016/j.ijrmhm.2019.104970.10.1016/j.ijrmhm.2019.104970 ↗
15. Fatima A, Mativenga PT. Performance of flank face structured cutting tools in machining of AISI/SAE 4140 over a range of cutting speeds. Proc Inst Mech Eng Part B J Eng Manuf. 2016;230:3–18. https://doi.org/10.1177/0954405414555589.10.1177/0954405414555589 ↗
16. Sugihara T, Nishimoto Y, Enomoto T. Development of a novel cubic boron nitride cutting tool with a textured flank face for high-speed machining of Inconel 718. Precis Eng. 2017;48:75–82. https://doi.org/10.1016/j.precisioneng.2016.11.007.10.1016/j.precisioneng.2016.11.007 ↗
17. Sun J, Duan R, Wang Q, Chen H, Ye S. Derivative cutting prediction model for flank-faced textured tools. Int J Adv Manuf Technol. 2025;140:1689–704. https://doi.org/10.1007/s00170-025-16424-8.10.1007/s00170-025-16424-8 ↗
18. Liu Y, Deng J, Wang W, Duan R, Meng R, Ge D, et al. Effect of texture parameters on cutting performance of flank-faced textured carbide tools in dry cutting of green Al2O3 ceramics. Ceram Int. 2018;44:13205–17. https://doi.org/10.1016/j.ceramint.2018.04.146.10.1016/j.ceramint.2018.04.146 ↗
19. Liu Y, Deng J, Wu F, Duan R, Zhang X, Hou Y. Wear resistance of carbide tools with textured flank-face in dry cutting of green alumina ceramics. Wear. 2017;372–373:91–103. https://doi.org/10.1016/j.wear.2016.12.001.10.1016/j.wear.2016.12.001 ↗
20. Kümmel J, Braun D, Gibmeier J, Schneider J, Greiner C, Schulze V, et al. Study on micro texturing of uncoated cemented carbide cutting tools for wear improvement and built-up edge stabilisation. J Mater Process Technol. 2015;215:62–70. https://doi.org/10.1016/j.jmatprotec.2014.07.032.10.1016/j.jmatprotec.2014.07.032 ↗
21. Gao B, Tang K, Deng Z, Chen Z, Yuan L, Wang W. A review of laser-assisted cutting of hard and brittle materials: tools, devices and mechanisms. Opt Laser Technol. 2025;189:113105. https://doi.org/10.1016/j.optlastec.2025.113105.10.1016/j.optlastec.2025.113105 ↗
22. Shafeeque TP, George A, Mathew J, Kuriachen B. Force modeling and experimental investigations on machinability of SDSS 2507 under dry turning conditions using CVD TiCN-Al2O3 coated tools. Sādhanā. 2024. https://doi.org/10.1007/s12046-024-02585-x.10.1007/s12046-024-02585-x ↗
23. Pawanr S, Gupta K. Preliminary Investigation of Tool Wear When Machining Super Duplex Stainless Steel Using Coated Inserts Under Dry Environment. Engineering Proceedings. 2025;4. https://doi.org/10.3390/engproc2025111004.10.3390/engproc2025111004 ↗
24. International Organization for Standardization, ISO 3685:1993 – Tool-life testing with single-point turning tools. (1993) 48.
25. Jiang Z, Shi G, Meng S, Liu J, Kong D. Research on micro-texture design of tools’ surface by topology optimization on cutting performance. Int J Adv Manuf Technol. 2025;139:1311–23. https://doi.org/10.1007/s00170-025-15932-x.10.1007/s00170-025-15932-x ↗
26. Zhang J, Sun P, Ali Q, Wang J, Guo G, Li L, He N, Hao X. The biomimetic hierarchical micro-groove textured tool for enhancing lubrication and cooling. J Manuf Process. 2025;155:72–81. https://doi.org/10.1016/j.jmapro.2025.10.011.10.1016/j.jmapro.2025.10.011 ↗
27. Lu J, Khawarizmi R, Monclús M, Molina-Aldareguia J, Kwon P, Bieler TR. Effect of cutting speed on shear band formation and chip morphology of Ti–6Al–4V alloy using nanoindentation and EBSD mapping. Mater Sci Eng A. 2023;862:144372. https://doi.org/10.1016/j.msea.2022.144372.10.1016/j.msea.2022.144372 ↗
28. Mf A, Rb S, Rk P, B C, Js S, Sr D. Performance analysis of dimple micro-textured inserts with varying shape factor in machining. J Manuf Process. 2025;156:381–97. https://doi.org/10.1016/j.jmapro.2025.11.042.10.1016/j.jmapro.2025.11.042 ↗
29. Akıncıoğlu S. Taguchi optimization of multiple performance characteristics in the electrical discharge machining of the Tigr2. Facta Univ Ser Mech Eng. 2022;20:237–53. https://doi.org/10.22190/FUME201230028A.10.22190/FUME201230028A ↗