journal article·2025-12-28Open access

Pulsed operation of a DC welding power source in resistance projection welding

Zygmunt Mikno, Mariusz Stepien, Wenqi Zhang, Murali Tumuluru

Abstract

Abstract The effect of pulse welding current (DC, 1 kHz) on the progression of projection welding process of nuts was analysed. The study involved a comparative analysis using identical average value for pulsed DC current with continuous direct current (DCc), which is commonly used in conventional mode. The analysis was conducted for nuts featuring four trapezoidal projections, made of grade 10B21 steel (AISI1017-SORPAS library), with a projection height of 1.2 mm and an initial contact area between the projection and the sheet metal of 7.8 mm 2 . The second welded component was a 3.0 mm thick DC04 sheet metal. Numerical analyses in both cases were conducted using the SORPAS ™ software. The characteristic parameters evaluated were weld strength, volume of melted material (in both the sheet and the projection), area of molten material in the contact region, welding energy, and average welding current. The results of the numerical calculations were verified experimentally. The study demonstrated the beneficial effect of pulsed welding current (DC, 1 kHz) on weld quality, particularly in terms of improved strength. It is possible to both reduce welding time and increase weld strength for pulsed DC welding. With comparable weld strength, welding time can be reduced by over 30%. In turn, for the same welding time (and thus the same energy), the weld strength can be increased by 35%.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Welding Techniques and Residual Stresses · Electromagnetic Effects on Materials · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (27)

Show source-provided references
1. Zhou K, Yao P. Review of application of the electrical structure in resistance spot welding. IEEE Access. 2017. https://doi.org/10.1109/ACCESS.2017.2771310.10.1109/ACCESS.2017.2771310 ↗
2. Alfaro SCA, Vargas JE, Wolff MA, Vilarinho LO. Comparison between AC and MF-DC resistance spot welding by using high speed filming. J Achiev Mater Manuf Eng. 2007;24(1):333–9.
3. Hwang IS, Kim DC, Kan MJ. Inverter DC resistance spot welding of magnesium alloy AZ3. Mater Manuf Proc. 2011;48(2):112–7.
4. Ji C, Park Ch, Kim Ch, Cho Y, Oh D, Kim MH, et al. A comparative study of weldable current range on AC and MFDC resistance spot welding for 440 MPa grade steel sheet. J Weld Join. 2017;35(1):34–42. https://doi.org/10.5781/JWJ.2017.35.1.34.10.5781/JWJ.2017.35.1.34 ↗
5. Srinivasan D, Sevvel P, Solomon IJ, Tanushkumaar P. A review on cold metal transfer (CMT) technology of welding. Mater Today Proc. 2023;64:108–15. https://doi.org/10.1016/j.matpr.2022.04.016.10.1016/j.matpr.2022.04.016 ↗
6. Selvi S, Vishvaksenan A, Rajasekar E. Cold metal transfer (CMT) technology—an overview. Def Technol. 2018;14(1):28–44. https://doi.org/10.1016/j.dt.2017.08.002.10.1016/j.dt.2017.08.002 ↗
7. Sun Z, Lv Y, Xu B, Liu Y, Lin J, Wang K. Investigation of droplet transfer behaviours in cold metal transfer (CMT) process on welding Ti-6Al-4V alloy. Int J Adv Manuf Technol. 2015;80(9–12):2007–14. https://doi.org/10.1007/s00170-015-7197-9.10.1007/s00170-015-7197-9 ↗
8. Chen X, Su C, Wang Y, Siddiquee AN, Sergey K, Jayalakshmi S, et al. Cold metal transfer (CMT) based wire and arc additive manufacture (WAAM) system. J Surf Investig: X-Ray Synchrotron Neutron Tech. 2018;12(6):1278–84.10.1134/S102745101901004X ↗
9. Gao T, Peng C, Zhu R, Li Ch, Duan L, Suen H, et al. Effect of pulsed current-assisted CMT welding parameters on friction and wear properties and electrochemical corrosion performance of heterogeneous structure composites. J Mater Res Technol. 2025;39:3426–43. https://doi.org/10.1016/j.jmrt.2025.10.033.10.1016/j.jmrt.2025.10.033 ↗
10. Cong B, Ding J, Williams S. Effect of arc mode in cold metal transfer process on porosity of additively manufactured Al-6.3% Cu alloy. Int J Adv Manuf Technol. 2014;76(9):1593–606. https://doi.org/10.1007/s00170-014-6346-x.10.1007/s00170-014-6346-x ↗
11. Wu CS, Wang L, Ren WJ, Zhang XY. Plasma arc welding: process, sensing, control and modeling. J Manuf Process. 2014;16(1):74–85. https://doi.org/10.1016/j.jmapro.2013.06.004.10.1016/j.jmapro.2013.06.004 ↗
12. Kamal P, Surjya KP. Effect of pulse parameters on weld quality in pulsed gas metal arc welding: a review. J Mater Eng Perform. 2011;20:918–31. https://doi.org/10.1007/s11665-010-9717.10.1007/s11665-010-9717 ↗
13. Zhu ZM, Wu WK, Chen Q. Robotic Welding, Intelligence and Automation, Chapter—Numerical Simulation of Molten Droplet Shape and Electromagnetic Pinch Effect in Short-Circuit CO2. Springer-Verlag Berlin Heidelberg Welding, ISSN electronic edition; 2007.p. 1610–7411
14. Singh J, Arora KS, Oliveira JP. Unravelling the influence of CMT characteristic parameters on process stability and joint properties in dissimilar aluminium-steel weld-brazing. J Manuf Process. 2025;135:253–68. https://doi.org/10.1016/j.jmapro.2025.01.040.10.1016/j.jmapro.2025.01.040 ↗
15. Singh J, Arora KS, Oliveira JP, Asati B. Comparative analysis of MIG brazing modes: process stability, bead morphology, microstructure, and mechanical properties. Int J Adv Manuf Technol. 2024;135:137–54. https://doi.org/10.1007/s00170-024-14488-6.10.1007/s00170-024-14488-6 ↗
16. Chludzinski M, Santos Re, Churiaque C, Sánchez-Amaya jM. Pulsed laser welding applied to metallic materials—a material approach. Metals. 2021;11:640. https://doi.org/10.3390/met11040640.10.3390/met11040640 ↗
17. Wang Ch, Yan Y, Ding F, Tang Z, Chen W, Zhu X. Effect of pulsed laser welding process on microstructure, crystallization, and mechanical properties of Zr57Nb5Cu15.4Ni12.6Al10 bulk metallic glass. Chin J Mech Eng. 2025;38:17. https://doi.org/10.1186/s10033-025-01181-2.10.1186/s10033-025-01181-2 ↗
18. Adin MS. A parametric study on the mechanical properties of MIG and TIG welded dissimilar steel joints. J Adhes Sci Technol. 2024;38(1):115–38. https://doi.org/10.1080/01694243.2023.2221391.10.1080/01694243.2023.2221391 ↗
19. Wang X, Zhang Y. Effect of welding procedures of resistance projection welding of nuts to sheets. ISIJ Int. 2017;57(12):2194–200. https://doi.org/10.2355/isijinternational.ISIJINT-2017-219.10.2355/isijinternational.ISIJINT-2017-219 ↗
20. Wei PS, Wu TH. Effects of electrical current on transport processes in resistance spot welding. Sci Technol Weld Join. 2010;15(6):448–56. https://doi.org/10.1179/136217110X12693513264295.10.1179/136217110X12693513264295 ↗
21. Zhou K, Yu W, Wang G, et al. Comparative analysis between multi-pulse and constant welding current for resistance spot welding process. J Mater Sci. 2023;58:2853–75. https://doi.org/10.1007/s10853-023-08191-2.10.1007/s10853-023-08191-2 ↗
22. Mikno Z, Stępień M. Comparative analysis of a projection welding process with AC and DC current source for susceptibility study, IIW Commission III 2024, 28.02–1.03.2024. Columbus/Ohio, USA, Document No. III-2190-24; 2023.
23. Mikno Z, Stępień M, Xia Y-J. Comparative analysis of a projection welding process with AC and DC current source for susceptibility study. Int J Adv Manuf Technol. 2025. https://doi.org/10.1007/s00170-025-16168-5.10.1007/s00170-025-16168-5 ↗
24. SORPAS® 3D Version 7.50, Copyright© 2007–2024 by SWANTEC Software and Engineering Ap S (Licence ID: SP483001-3D.
25. SWANTEC—The database of the material and electrode parameters: model 2D version 11.2 and model 3D Version 4.0x64 of the Swantec Inc. SORPAS Software.
26. Mikno Z, Stępień M. Comparative analysis of a projection welding process with AC and DC current source for susceptibility study, Document No. III-2190–24. Columbus/Ohio USA; 2024
27. Mikno Z, Stępień M, Zhang W. Pulsed operation of the DC welding power source in the aspect of numerical calculations, Document No. III-2297–25. Dresden/Germany; 2025.10.1007/s43452-025-01401-5 ↗