Solid-state welding of UFG copper rods with conical face by means of friction heat impulse
Source abstract
Abstract
Abstract Solid-state friction welding of ultra-fine grained materials (UFG) is a complex process to implement. Exceeding the recrystallization temperature during the process causes degradation of the material’s properties. The process temperature can be reduced by limiting the heat power. Using standard friction welding machines and parameters, it is difficult to achieve an appropriately low heat power. The welding tests of Cu-ETP copper with an UFG structure were carried out on a prototype rotary friction welding machine. It enables welding materials with extremely short friction times and high pressure forces. A given set of non-standard/sharp parameters influences the generated heat power. Its characteristic course is called the friction heat impulse (FHI). The use of FHI allows the energy to be reduced to the minimum necessary to obtain a joint. In order to obtain better joint conditions in a short welding time, a conical surface was used on one of the welded samples. The friction welding tests carried out using the FHI method and a prototype machine showed that the average hardness value of the joints increased slightly from 129 HV0.2 to 130 HV0.2. Additionally, the tensile strength remained at the same level as the UFG base material. The results proved that it is possible to weld UFG copper rods with conical face under recrystallization temperature without any signs of degradation of the UFG structure.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Welding Techniques and Residual Stresses · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (36)
Show source-provided references
1. Shinde G, Dabeer P. Review of experimental investigations in friction welding technique. Int J Technol Eng. 2017;7:373–84. https://doi.org/10.21013/jte.ICSESD201736.10.21013/jte.ICSESD201736 ↗
2. Vairis A. Linear friction welded titanium alloy joints: a brief review of microstructure evolution and mechanical properties. Weld Int. 2022;36:647–54. https://doi.org/10.1080/09507116.2022.2149366.10.1080/09507116.2022.2149366 ↗
3. Ahmed MMZ, El-Sayed Seleman MM, Fydrych D, Çam G. Friction stir welding of aluminum in the aerospace industry: the current progress and state-of-the-art review. Materials. 2023;16:2971. https://doi.org/10.3390/ma16082971.10.3390/ma16082971 ↗
4. Chamanfar A, Jahazi M, Cormier J. A review on inertia and linear friction welding of Ni-based superalloys. Metall Mater Trans A. 2015;46:1639–69. https://doi.org/10.1007/s11661-015-2752-4.10.1007/s11661-015-2752-4 ↗
5. Titouche N-E, Boukharouba T, Amzert SA, Jabbar Hassan A, Lechelah R, Ramtani S. Direct drive friction welding effect on mechanical and electrochemical characteristics of titanium stabilized austenitic stainless steel (AISI 321) research reactor thick tube. J Manuf Process. 2019;41:273–83. https://doi.org/10.1016/j.jmapro.2019.03.016.10.1016/j.jmapro.2019.03.016 ↗
6. Raimondi L, Bennett CJ, Axinte D, Gameros A, Stevens PA. Development of a novel monitoring system for the in-process characterisation of the machine and tooling effects in inertia friction welding (IFW). Mech Syst Signal Process. 2021;156: 107551. https://doi.org/10.1016/j.ymssp.2020.107551.10.1016/j.ymssp.2020.107551 ↗
7. Ahmad Mir F, Zaman Khan N, Noor Siddiquee A, Parvez S. Friction based solid state welding—a review. Mater Today Proc. 2022;62:55–62. https://doi.org/10.1016/j.matpr.2022.01.457.10.1016/j.matpr.2022.01.457 ↗
8. Guo W, You G, Yuan G, Zhang X. Microstructure and mechanical properties of dissimilar inertia friction welding of 7A04 aluminum alloy to AZ31 magnesium alloy. J Alloy Compd. 2017;695:3267–77. https://doi.org/10.1016/j.jallcom.2016.11.218.10.1016/j.jallcom.2016.11.218 ↗
9. Hassan AJ, Titouche NE, Amzert SA, Cheniti B, Belkessa B, Boukharouba T, Miroud D. Direct drive friction welding influence on metallurgical, mechanical, and electrochemical properties of AISI 316. Exp Tech. 2024. https://doi.org/10.1007/s40799-024-00718-9.10.1007/s40799-024-00718-9 ↗
10. Skowrońska B, Chmielewski T, Zasada D. Assessment of selected structural properties of high-speed friction welded joints made of unalloyed structural steel. Materials. 2023;16:93. https://doi.org/10.3390/ma16010093.10.3390/ma16010093 ↗
11. Li W, Vairis A, Preuss M, Ma T. Linear and rotary friction welding review. Int Mater Rev. 2016;61:71–100. https://doi.org/10.1080/09506608.2015.1109214.10.1080/09506608.2015.1109214 ↗
12. Arbuz A, Kawalek A, Ozhmegov K, Dyja H, Panin E, Lepsibayev A, Sultanbekov S, Shamenova R. Using of radial-shear rolling to improve the structure and radiation resistance of zirconium-based alloys. Materials. 2020;13:4306. https://doi.org/10.3390/ma13194306.10.3390/ma13194306 ↗
13. Azushima A, Kopp R, Korhonen A, Yang DY, Micari F, Lahoti GD, Groche P, Yanagimoto J, Tsuji N, Rosochowski A, Yanagida A. Severe plastic deformation (SPD) processes for metals. CIRP Ann. 2008;57:716–35. https://doi.org/10.1016/j.cirp.2008.09.005.10.1016/j.cirp.2008.09.005 ↗
14. Radhi HN, Aljassani AMH, Mohammed MT. Effect of ECAP on microstructure, mechanical and tribological properties of aluminum and brass alloys: a review. Mater Today Proc. 2020;26:2302–7. https://doi.org/10.1016/j.matpr.2020.02.497.10.1016/j.matpr.2020.02.497 ↗
15. Venkateswarlu K, Ghosh M, Ray AK, Xu C, Langdon TG. On the feasibility of using a continuous processing technique incorporating a limited strain imposed by ECAP. Mater Sci Eng, A. 2008;485:476–80. https://doi.org/10.1016/j.msea.2007.08.007.10.1016/j.msea.2007.08.007 ↗
16. Morawiński Ł, Chmielewski T, Olejnik L, Buffa G, Campanella D, Fratini L. Welding abilities of UFG metals. AIP Conf Proc. 2018;1960: 050012. https://doi.org/10.1063/1.5034885.10.1063/1.5034885 ↗
17. Orłowska M, Brynk T, Hütter A, Goliński J, Enzinger N, Olejnik L, Lewandowska M. Similar and dissimilar welds of ultrafine grained aluminium obtained by friction stir welding. Mater Sci Eng A. 2020;777: 139076. https://doi.org/10.1016/j.msea.2020.139076.10.1016/j.msea.2020.139076 ↗
18. Sato YS, Urata M, Kokawa H, Ikeda K, Enomoto M. Retention of fine grained microstructure of equal channel angular pressed aluminum alloy 1050 by friction stir welding. Scripta Mater. 2001;45:109–14. https://doi.org/10.1016/S1359-6462(01)01000-4.10.1016/S1359-6462(01)01000-4 ↗
19. Sabooni S, Karimzadeh F, Enayati MH, Ngan AHW. Friction-stir welding of ultrafine grained austenitic 304L stainless steel produced by martensitic thermomechanical processing. Mater Des. 2015;76:130–40. https://doi.org/10.1016/j.matdes.2015.03.052.10.1016/j.matdes.2015.03.052 ↗
20. Ueji R, Fujii H, Cui L, Nishioka A, Kunishige K, Nogi K. Friction stir welding of ultrafine grained plain low-carbon steel formed by the martensite process. Mater Sci Eng A. 2006;423:324–30. https://doi.org/10.1016/j.msea.2006.02.038.10.1016/j.msea.2006.02.038 ↗
21. Lipińska M, Pixner F, Szachogłuchowicz I, Mittermayr F, Grengg C, Enzinger N, Lewandowska M. Application of electron beam welding technique for joining coarse-grained and ultrafine-grained plates from Al-Mg-Si alloy. J Manuf Process. 2023;104:28–43. https://doi.org/10.1016/j.jmapro.2023.08.057.10.1016/j.jmapro.2023.08.057 ↗
22. Sahin M, Erol Akata H, Ozel K. An experimental study on joining of severe plastic deformed aluminium materials with friction welding method. Mater Des. 2008;29:265–74. https://doi.org/10.1016/j.matdes.2006.11.004.10.1016/j.matdes.2006.11.004 ↗
23. Ciemiorek M, Morawiński Ł, Jasiński C, Orłowska M, Chmielewski T, Olejnik L, Lewandowska M. Characterization of ultrafine-grained copper joints acquired by rotary friction welding. Archiv Civ Mech Eng. 2021;22:9. https://doi.org/10.1007/s43452-021-00326-z.10.1007/s43452-021-00326-z ↗
24. Skowrońska B, Chmielewski T, Kulczyk M, Skiba J, Przybysz S. Microstructural investigation of a friction-welded 316L stainless steel with ultrafine-grained structure obtained by hydrostatic extrusion. Materials. 2021;14:1537. https://doi.org/10.3390/ma14061537.10.3390/ma14061537 ↗
25. Jiang Q-W, Li X-W. Effect of pre-annealing treatment on the compressive deformation and damage behavior of ultrafine-grained copper. Mater Sci Eng A. 2012;546:59–67. https://doi.org/10.1016/j.msea.2012.03.024.10.1016/j.msea.2012.03.024 ↗
26. Kimura M, Nakashima K, Kusaka M, Kaizu K, Nakatani Y, Takahashi M. Joining phenomena and tensile strength of joint between Ni-based superalloy and heat-resistant steel by friction welding. Int J Adv Manuf Technol. 2019;103:1297–308. https://doi.org/10.1007/s00170-019-03611-7.10.1007/s00170-019-03611-7 ↗
27. Morawiński Ł, Jasiński C, Ciemiorek M, Chmielewski T, Olejnik L, Lewandowska M. Solid-state welding of ultrafine grained copper rods. Archiv Civ Mech Eng. 2021;21:89. https://doi.org/10.1007/s43452-021-00244-0.10.1007/s43452-021-00244-0 ↗
28. Zhang C, Wang S, Luo D, Shi W, Liu X, Cui G, Chen B, Xin Z, Rui Z. Study of the mechanical properties and microstructures of conical joints for aluminum/steel continuous drive friction welding. J Manuf Process. 2021;67:241–52. https://doi.org/10.1016/j.jmapro.2021.04.070.10.1016/j.jmapro.2021.04.070 ↗
29. Ou Y, Deng Y, Zhao Y, Zeng J, Xiao S. Mechanical properties and microstructure of conical joints for dissimilar steels continuous drive friction welding. J Mater Eng Perform. 2023;32:5239–48. https://doi.org/10.1007/s11665-022-07486-w.10.1007/s11665-022-07486-w ↗
30. Alves EP, Toledo RC, Piorino Neto F, Botter FG, Ying An C. Experimental thermal analysis in rotary friction welding of dissimilar materials. J Aerosp Technol Manage. 2019;11:e4019. https://doi.org/10.5028/jatm.v11.1068.10.5028/jatm.v11.1068 ↗
31. Olejnik L, Rosochowski A. Scaled-up ECAP with enhanced productivity. Steel Res Int. 2008;2:439–47.
32. Presz W, Jasiński C, Morawiński Ł, Orłowska M. Material forming ESAFORM 2023. Mater Res Proc. 2023;28:825–32. https://doi.org/10.21741/9781644902479-90.10.21741/9781644902479-90 ↗
33. Morawiński Ł, Jasiński C, Goliński J, Chmielewski TM. Friction welding of UFG copper using the W2Mi prototype machine. Arch Civ Mech Eng. 2024;24:139. https://doi.org/10.1007/s43452-024-00955-0.10.1007/s43452-024-00955-0 ↗
34. Morawiński Ł, Jasiński C, Goliński J, Chmielewski TM. Joining UFG copper by means of the W2Mi machine. Arch Metall Mater. 2024;69(4):1529–35. https://doi.org/10.24425/amm.2024.151423.10.24425/amm.2024.151423 ↗
35. Kimura M, Kusaka M, Seo K, Fuji A. Improving joint properties of friction welded joint of high tensile steel. JSME Int J Ser A Solid Mech Mater Eng. 2005;48:399–405. https://doi.org/10.1299/jsmea.48.399.10.1299/jsmea.48.399 ↗
36. Deepesh V, Amal VP, Muthukumaran S, Sastikumar D. Studies on the role of total welding rotation in friction welding of tube-to-tube plate using an external tool. J Manuf Process. 2020;53:110–22. https://doi.org/10.1016/j.jmapro.2020.02.004.10.1016/j.jmapro.2020.02.004 ↗