journal article·2025-04-09Open access

Surface topography and subsurface integrity of titanium grade 2 machined by nanosecond laser: the effects of scanning speed, laser power, and frequency

Evangelos Nikolidakis, Emmanouil L. Papazoglou, Nikolaos E. Karkalos, Beata Leszczyńska-Madej, Panagiotis Karmiris-Obratański

Abstract

Abstract Surface quality is a major requirement in industrial level for every mechanical part, as it can define not only their ability to be appropriately used in assemblies but also their service life. Nowadays, the increased capabilities of modern measurement equipment have allowed the study of more advanced parameters such as the uniformity of texture or functional parameters of the roughness profile, which can lead to reliable conclusions about tribological and lubrication properties of machined surfaces as well. In the present case, a thorough investigation of surface topography and texture was carried out for the case of laser engraving of square pockets on a titanium alloy workpiece under diverse process conditions. Analysis of the results revealed that apart from the high correlation of laser power and laser scanning speed with amplitude parameters of surface roughness, laser engraving can have a profound effect on directionality of the produced texture, with higher speeds and moderate VED values leading to less isotropic surfaces. Moreover, although based on the analysis of Ssk and Sku values, which were found to be mostly positive and below 4 respectively, most surfaces exhibit high peaks and reduced fluid retention capability, the latter can be increased by appropriately selecting the combination of process conditions during laser engraving process.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Laser Material Processing Techniques · Advanced Surface Polishing Techniques · Advanced machining processes and optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (64)

Show source-provided references
1. Whitehouse DJ. Surface characterization and roughness measurement in engineering. In: Rastogi PK, editor. 1st ed. Springer; 2000. p. 413–61.10.1007/3-540-48800-6_12 ↗
2. Leach R. Characterisation of areal surface texture. Berlin: Springer; 2013.10.1007/978-3-642-36458-7 ↗
3. Pawlus P, Reizer R, Wieczorowski M, Królczyk G. Parametric description of one-process surface texture. Meas J Int Meas Confed. 2022. https://doi.org/10.1016/j.measurement.2022.112066.10.1016/j.measurement.2022.112066 ↗
4. Leach R, Weckenmann A, Coupland J, Hartmann W. Interpreting the probe-surface interaction of surface measuring instruments, or what is a surface? Surf Topogr Metrol Prop. 2014. https://doi.org/10.1088/2051-672X/2/3/035001.10.1088/2051-672X/2/3/035001 ↗
5. Leach R. Surface texture. In: CIRP encyclopedia of production engineering. Berlin: Springer; 2014. p. 1–4.
6. Somers N, Lasgorceix M (2021) Surface treatment of bioceramics. In: Encyclopedia of materials: technical ceramics and glasses. Elsevier, pp 701–71510.1016/B978-0-12-818542-1.00032-1 ↗
7. Pawlus P, Reizer R, Wieczorowski M, Krolczyk GM. Sensitivities of surface texture parameters to measurement errors—a review. Measurement. 2024;227: 114323. https://doi.org/10.1016/j.measurement.2024.114323.10.1016/j.measurement.2024.114323 ↗
8. Benardos PG, Vosniakos G-C. Predicting surface roughness in machining: a review. Int J Mach Tools Manuf. 2003;43:833–44. https://doi.org/10.1016/S0890-6955(03)00059-2.10.1016/S0890-6955(03)00059-2 ↗
9. Zhang S, Li Y, Wang G, et al. A novel method for calculating the fractal dimension of three-dimensional surface topography on machined surfaces. Chaos Solitons Fractals. 2024;180: 114573. https://doi.org/10.1016/j.chaos.2024.114573.10.1016/j.chaos.2024.114573 ↗
10. Tan CY, Wen C, Ang HQ. Influence of laser parameters on the microstructures and surface properties in laser surface modification of biomedical magnesium alloys. J Magnes Alloy. 2024;12:72–97. https://doi.org/10.1016/j.jma.2023.12.008.10.1016/j.jma.2023.12.008 ↗
11. Dahotre NB, Harimkar SP. Laser fabrication and machining of materials. Boston: Springer US; 2008.
12. Shin YC, Wu B, Lei S, et al. Overview of laser applications in manufacturing and materials processing in recent years. J Manuf Sci Eng. 2020. https://doi.org/10.1115/1.4048397.10.1115/1.4048397 ↗
13. Nikolidakis E, Antoniadis A. FEM modeling and simulation of kerf formation in the nanosecond pulsed laser engraving process. CIRP J Manuf Sci Technol. 2021;35:236–49. https://doi.org/10.1016/j.cirpj.2021.06.014.10.1016/j.cirpj.2021.06.014 ↗
14. Schnell G, Duenow U, Seitz H. Effect of laser pulse overlap and scanning line overlap on femtosecond laser-structured Ti6Al4V surfaces. Materials (Basel). 2020;13:969. https://doi.org/10.3390/ma13040969.10.3390/ma13040969 ↗
15. Kasman Ş. Impact of parameters on the process response: a Taguchi orthogonal analysis for laser engraving. Meas J Int Meas Confed. 2013;46:2577–84. https://doi.org/10.1016/j.measurement.2013.04.022.10.1016/j.measurement.2013.04.022 ↗
16. Orazi L, Cuccolini G, Fortunato A, Tani G. An automated procedure for material removal rate prediction in laser surface micromanufacturing. Int J Adv Manuf Technol. 2010;46:163–71. https://doi.org/10.1007/s00170-009-2097-5.10.1007/s00170-009-2097-5 ↗
17. Šugár P, Šugárová J, Frnčík M, Ludrovcová B. Nanosecond YB fibre laser milling of alluminium bronze: effect of process parameters on the surface finish. Adv Sci Technol Res J. 2018;12:10–5. https://doi.org/10.12913/22998624/93613.10.12913/22998624/93613 ↗
18. Zhang W, Yao YL, Chen K. Modelling and analysis of UV laser micromachining of copper. Int J Adv Manuf Technol. 2001;18:323–31. https://doi.org/10.1007/s001700170056.10.1007/s001700170056 ↗
19. Yan Z, Mei X, Wang W, et al. Numerical simulation on nanosecond laser ablation of titanium considering plasma shield and evaporation-affected surface thermocapillary convection. Opt Commun. 2019;453: 124384. https://doi.org/10.1016/j.optcom.2019.124384.10.1016/j.optcom.2019.124384 ↗
20. Chen Y, Shao Y, Xiao X. A new method for predicting the morphology and surface roughness of micro grooves in aluminum alloy ablated by pulsed laser. J Manuf Process. 2023;96:193–203. https://doi.org/10.1016/j.jmapro.2023.03.057.10.1016/j.jmapro.2023.03.057 ↗
21. Dash B, Maity K. An investigation on the optimum laser machining parameters and its effect on NiTi shape memory alloy. Mater Today Proc. 2023;91:103–10. https://doi.org/10.1016/j.matpr.2023.05.562.10.1016/j.matpr.2023.05.562 ↗
22. Pritam A, Dash RR, Mallik RK. Predictive modeling and multi objective optimization of Al 6063 for engraving depth and surface roughness using grey relational and regression analysis. Mater Today Proc. 2023;80:3464–70. https://doi.org/10.1016/j.matpr.2021.07.271.10.1016/j.matpr.2021.07.271 ↗
23. Pattanayak S, Kumar Sahoo S. Micro engraving on 316L stainless steel orthopedic implant using fiber laser. Opt Fiber Technol. 2021;63: 102479. https://doi.org/10.1016/j.yofte.2021.102479.10.1016/j.yofte.2021.102479 ↗
24. Leyens C, Peters M. Titanium and titanium alloys. New York: Wiley; 2003.10.1002/3527602119 ↗
25. Gupta MK, El EH, Korkmaz ME, et al. Tribological and surface morphological characteristics of titanium alloys: a review. Arch Civ Mech Eng. 2022;22:1–23. https://doi.org/10.1007/s43452-022-00392-x.10.1007/s43452-022-00392-x ↗
26. Liang X, Liu Z, Wang B. State-of-the-art of surface integrity induced by tool wear effects in machining process of titanium and nickel alloys: a review. Meas J Int Meas Confed. 2019;132:150–81. https://doi.org/10.1016/j.measurement.2018.09.045.10.1016/j.measurement.2018.09.045 ↗
27. Pimenov DY, Mia M, Gupta MK, et al. Improvement of machinability of Ti and its alloys using cooling-lubrication techniques: a review and future prospect. J Mater Res Technol. 2021;11:719–53. https://doi.org/10.1016/j.jmrt.2021.01.031.10.1016/j.jmrt.2021.01.031 ↗
28. Pramanik A, Basak AK, Littlefair G, et al. Methods and variables in electrical discharge machining of titanium alloy—a review. Heliyon. 2020. https://doi.org/10.1016/j.heliyon.2020.e05554.10.1016/j.heliyon.2020.e05554 ↗
29. Pramanik A, Basak AK. Laser beam machining of titanium alloy—a review. Metals (Basel). 2023;13:1–16. https://doi.org/10.3390/met13091536.10.3390/met13091536 ↗
30. Gao K, Zhang Y, Yi J, et al. Overview of surface modification techniques for titanium alloys in modern material science: a comprehensive analysis. Coatings. 2024. https://doi.org/10.3390/coatings14010148.10.3390/coatings14010148 ↗
31. Eghbali N, Naffakh-Moosavy H, Sadeghi Mohammadi S, Naderi-Manesh H. The influence of laser frequency and groove distance on cell adhesion, cell viability, and antibacterial characteristics of Ti-6Al-4V dental implants treated by modern fiber engraving laser. Dent Mater. 2021;37:547–58. https://doi.org/10.1016/j.dental.2020.12.007.10.1016/j.dental.2020.12.007 ↗
32. Madapana D, Bathe R, Manna I, Majumdar JD. Effect of process parameters on the corrosion kinetics and mechanism of nanosecond laser surface structured titanium alloy (Ti6Al4V). Appl Surf Sci Adv. 2024;20: 100580. https://doi.org/10.1016/j.apsadv.2024.100580.10.1016/j.apsadv.2024.100580 ↗
33. Convert L, Bourillot E, François M, et al. Laser textured titanium surface characterization. Appl Surf Sci. 2022;586: 152807. https://doi.org/10.1016/j.apsusc.2022.152807.10.1016/j.apsusc.2022.152807 ↗
34. Khomich YV, Mikolutskiy SI. Surface blackening of titanium alloy by laser nanosecond pulses. Acta Astronaut. 2024;215:398–404. https://doi.org/10.1016/j.actaastro.2023.12.015.10.1016/j.actaastro.2023.12.015 ↗
35. Liu B, Wang C. Numerical simulation for the evolution in surface morphology of titanium alloy by nanosecond pulsed laser ablation. Mater Chem Phys. 2024;315: 128997. https://doi.org/10.1016/j.matchemphys.2024.128997.10.1016/j.matchemphys.2024.128997 ↗
36. Nordvik HR, Technology C. A comparison of commercially pure titanium produced according to the American ASTM grade 2 and the Russian GOST VT 1-0 standards. 1997. p. 799–806.
37. Iverson BL, Dervan PB. Titanium alloys for biomedical development and applications. Amsterdam: Elsevier; 2022.
38. Chen Q, Thouas GA. Metallic implant biomaterials. Mater Sci Eng R Reports. 2015;87:1–57. https://doi.org/10.1016/j.mser.2014.10.001.10.1016/j.mser.2014.10.001 ↗
39. Denker B, Shklovsky E. Handbook of solid-state lasers: materials, systems and applications. 201310.1533/9780857097507 ↗
40. Lawrence J, Waugh DG. Laser surface engineering. Amsterdam: Elsevier; 2015.
41. Szymański M, Przestacki D, Szymański P. The influence of selected laser engraving parameters on surface conditions of hybrid metal matrix composites. Materials. 2023;16(19):6575. https://doi.org/10.3390/ma16196575.10.3390/ma16196575 ↗
42. Khan MMA, Saha S, Romoli L, Kibria MH. Optimization of laser engraving of acrylic plastics from the perspective of energy consumption, CO2 emission and removal rate. J Manuf Mater Process. 2021;5(3):78. https://doi.org/10.3390/jmmp5030078.10.3390/jmmp5030078 ↗
43. Xing L, Arthanari S, Yingchun G, Ramakrishna S. Influence of assist gas on surface quality and microstructure development of laser metal processing. Opt Laser Technol. 2021;143: 107310. https://doi.org/10.1016/j.optlastec.2021.107310.10.1016/j.optlastec.2021.107310 ↗
44. Zhu X, Zhang J, Cheng J, et al. Forming epoxy coatings on laser-engraved surface of aluminum alloy to reinforce the bonding joint with a carbon fiber composite. Coatings. 2024;14(9):1201. https://doi.org/10.3390/coatings14091201.10.3390/coatings14091201 ↗
45. Richhariya V, Miranda G, Silva FS. An experimental parametric optimization for laser engraving and texturing to integrate zirconia ceramic blocks into stainless steel cutlery: a state-of-the-art aesthetically improved perspective. Materials. 2024;17(10):2452. https://doi.org/10.3390/ma17102452.10.3390/ma17102452 ↗
46. Nikolidakis E, Antoniadis A. FEM modeling simulation of laser engraving. Int J Adv Technol Manuf. 2019;105(3489):3498. https://doi.org/10.1007/s00170-019-04603-3.10.1007/s00170-019-04603-3 ↗
47. Mattinen M, Hirvimäki M, Poutiainen I, Salminen A. Effect of pulse length on engraving efficiency in nanosecond pulsed laser engraving of stainless steel. Metall Mater Trans B. 2015;46:2129–36.10.1007/s11663-015-0415-x ↗
48. Balchev I, Atanasov A, Lengerov A, Lazov L. Investigation of the influence of scanning speed and step in laser marking and engraving of aluminum. J Phys Conf Ser. 2021;1859: 021002. https://doi.org/10.1088/1742-6596/1859/1/012002.10.1088/1742-6596/1859/1/012002 ↗
49. Alexopoulou VE, Markopoulos AP. A critical assessment regarding two-temperature models: an investigation of the different forms of two-temperature models, the various ultrashort pulsed laser models and computational methods. Dordrecht: Springer; 2023.
50. Wischeropp TM. Advancement of selective laser melting by laser beam shaping. Berlin: Springer; 2021.10.1007/978-3-662-64585-7 ↗
51. Ba ECT, Dumont MR, Martins PS, et al. Investigation of the effects of skewness Rsk and kurtosis Rku on tribological behavior in a pin-on-disc test of surfaces machined by conventional milling and turning processes. Mater Res. 2021. https://doi.org/10.1590/1980-5373-mr-2020-0435.10.1590/1980-5373-mr-2020-0435 ↗
52. Królczyk G, Kacalak W, Wieczorowski M. 3D parametric and nonparametric description of surface topography in manufacturing processes. Materials (Basel). 2021;14:1987. https://doi.org/10.3390/ma14081987.10.3390/ma14081987 ↗
53. Duo Y, Tang J, Zhao Z, et al. Discrimination of wear performance based on surface roughness parameters arithmetic mean height (Sa) and skewness (Ssk). Wear. 2024;548–549: 205397. https://doi.org/10.1016/j.wear.2024.205397.10.1016/j.wear.2024.205397 ↗
54. Adamczak S, Swiderski J. Tools for comparative analysis of a surface texture formed by turning. Mechanik. 2017;90(10):906–8. https://doi.org/10.17814/mechanik.2017.10.143.10.17814/mechanik.2017.10.143 ↗
55. Krolczyk GM, Maruda RW, Krolczyk JB, et al. Parametric and nonparametric description of the surface topography in the dry and MQCL cutting conditions. Measurement. 2018;121:225–39. https://doi.org/10.1016/j.measurement.2018.02.052.10.1016/j.measurement.2018.02.052 ↗
56. Matuszewski M, Mikolajczyk T, Pimenov DY, Styp-Rekowski M. Influence of structure isotropy of machined surface on the wear process. Int J Adv Manuf Technol. 2017;88:2477–83. https://doi.org/10.1007/s00170-016-8963-z.10.1007/s00170-016-8963-z ↗
57. Leksycki K, Feldshtein E, Królczyk GM, Legutko S. On the chip shaping and surface topography when finish cutting 17–4 PH precipitation-hardening stainless steel under near-dry cutting conditions. Materials (Basel). 2020;13:2188. https://doi.org/10.3390/ma13092188.10.3390/ma13092188 ↗
58. Macek W, Rozumek D, Królczyk GM. Surface topography analysis based on fatigue fractures obtained with bending of the 2017A–T4 alloy. Measurement. 2020;152: 107347. https://doi.org/10.1016/j.measurement.2019.107347.10.1016/j.measurement.2019.107347 ↗
59. Pu Y, Zhao Y, Zhao G, et al. A study on work hardening in the laser-assisted machining of Si3N4 ceramics under different material removal modes. Metals (Basel). 2020;10:432. https://doi.org/10.3390/met10040432.10.3390/met10040432 ↗
60. Nwaogu UC, Tiedje NS, Hansen HN. A non-contact 3D method to characterize the surface roughness of castings. J Mater Process Technol. 2013;213:59–68. https://doi.org/10.1016/j.jmatprotec.2012.08.008.10.1016/j.jmatprotec.2012.08.008 ↗
61. Pawlus P, Reizer R, Wieczorowski M. Functional importance of surface texture parameters. Materials (Basel). 2021;14:5326. https://doi.org/10.3390/ma14185326.10.3390/ma14185326 ↗
62. Lipiński D, Banaszek K, Mathia TG. New methodology for discrimination of topography diversity of engineering surfaces—case of grinding. Measurement. 2022;190: 110659. https://doi.org/10.1016/j.measurement.2021.110659.10.1016/j.measurement.2021.110659 ↗
63. Molnar V, Szabo G. Designation of minimum measurement area for the evaluation of 3D surface texture. J Manuf Process. 2022;83:40–8. https://doi.org/10.1016/j.jmapro.2022.08.042.10.1016/j.jmapro.2022.08.042 ↗
64. Grzesik W, Rech J, Żak K. Characterization of surface textures generated on hardened steel parts in high-precision machining operations. Int J Adv Manuf Technol. 2015;78:2049–56. https://doi.org/10.1007/s00170-015-6800-4.10.1007/s00170-015-6800-4 ↗