journal article·2023-06-22

Compressive deformation/failure of cement–asphalt mortars

Yongliang Liu, Mulan Mu, Junjie Wang

Publisher page

Abstract

Cement–asphalt mortar (CAM) has been widely used as a cushion layer in prefabricated concrete slab tracks. However, the deformation and failure of different CAMs under compression are scarcely understood. In this study, therefore, we studied the compressive deformation and failure modes of CAMs with different asphalt–cement ratios (A/Cs or m(A)/m(C) = 0.2 ~ 1.0) together with the temperature effects, to understand the mechanisms behind their mechanical behaviour. Results indicated that, at room temperature, CAMs with low A/Cs (0.2 ~ 0.4), namely CAM-Ls, deformed and failed in a quasi-brittle manner, whereas CAMs with high A/Cs (0.8 ~ 1.0), namely CAM-Hs, were more like ductile materials. The temperature effect could be negligible for CAM-Ls, but significant for CAM-Hs. Low temperatures would cause a ductile-to-brittle transition in CAM-Hs and high temperatures would pose an adverse effect on their deformation and failure under compression. To understand the deformation and failure mechanisms of different CAMs and the temperature effects, microstructural models for CABs with relevant A/Cs were proposed. The microstructural models of CABs demonstrated that the compressive deformation and failure of CAMs depend primarily on their CABs. It is also indicated that, experimentally and theoretically, the boundary A/C value between CAM-Ls and CAM-Hs might be around 0.6, below which the hardened cement paste (hcp) form the matrix of the CAM, whilst above which the asphalt binder turns to the primary continuous phase in the CAB. Due to the microstructure change in CABs with the increasing A/C, the CAMs transitioned from quasi-brittle to ductile materials under compression.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Asphalt Pavement Performance Evaluation · Infrastructure Maintenance and Monitoring · Innovative concrete reinforcement materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. Ando K, Sunaga M, Aoki H, Haga O. Development of slab tracks for Hokuriku Shinkansen line. Q Rep RTRI. 2001;42(1):35–41.10.2219/rtriqr.42.35 ↗
2. Bastin R. Development of German non-ballasted track forms. Proc ICE Transp. 2006;159:25–39.
3. Jin S, Chen X, Yang J. Key technologies of CA mortar for slab track. China Railw Sci. 2006;27(2):20–5 ((In Chinese)).
4. Wang T, Hu S, Wang F, Liu Z, Gao T, Chen L. Research on main influencing factors on strength of CA Mortars. Railw Eng. 2008;2:109–11 ((In Chinese)).
5. Liu Y, Kong X, Zou Y, Yan P. Static and dynamic mechanical properties of cement asphalt mortars. J Railw Eng. 2009;6(3):1–7 ((In Chinese)).
6. Zhao P. Analysis of slab track's dynamic performance and study of parameter, Civil Engineering, Southwest Jiaotong University, Chengdu, Sichuan, P. R. China, 2003.
7. Liu X, Zhao P, Yang R, Wang P. Theory and method for ballastless track design in passenger dedicated lines. Chengdu, Sichuan Province China: Southwest Jiaotong University Press; 2010.
8. Zuo J, Jiang Q, Fu D. Research on CA mortars used as cushion layer in slab track. Railw Eng. 2005;9:96–8 ((In Chinese)).
9. Wang T, Hu S, Wang F, Liu Z, Gao T, Zou J, Mechanism study on the effects of mixing sequence of asphalt emulsion on strength development of CA mortar. Railw Constr Technol. 2007;(1) 1–3 (In Chinese).
10. Wang F, Liu Z, Hu S. Influence of loading rate on compressive strength of CA mortar. J BEIJING Univ Technol. 2008;34(10):1059–64 ((In Chinese)).
11. Wang Q, R A, Yan P. Influence of m(S) /m(C) and sand gradation on compressive strength and fluidity of CA mortar. J Railw Sci Eng. 2008;15(6):1–5 ((In Chinese)).
12. R A, Yan P, Wang Q. Research on the influencing factor of high strength cement asphalt mortar. J Build Mater. 2009;12(5):519–22 ((In Chinese)).
13. Kong X, Liu Y, Yan P. Temperature sensitivity of mechanical properties of cement asphalt mortars. J Chin Ceram Soc. 2010;38(4):553–7 ((In Chinese)).
14. Kong X, Liu Y, Yan P. Effect of loading rate on mechanical properties of cement asphalt mortars. J Build Mater. 2010;13(2):187–92 ((In Chinese)).
15. Xie Y, Zeng X, Deng D, Liu B, Zheng K. Mechanical characteristics of China railway track system (CRTS) I type slab tracks CA mortar under different strain rates. J Build Mater. 2010;13(4):483–6 ((In Chinese)).
16. Tan Y, Ouyang J, Wang J, Li Y, Cen H. Factors influencing strength of cement asphalt mortar and strength mechanism. J Harbin Inst Technol. 2011;43(10):80–3 ((In Chinese)).
17. Liu Y, Kong X, Zhang Y, Yan P. Effect of curing temperature on strength development of cement-asphalt mortars. J Build Mater. 2011;15(2):211–7 ((In Chinese)).
18. Liu Y, Kong X, Zhang Y, Yan P. Static and dynamic mechanical properties of cement-asphalt composites. J Mater Civil Eng. 2013;25(10):1489–97.10.1061/(ASCE)MT.1943-5533.0000681 ↗
19. Kong X, Liu Y, Zhang Y, Zhang Z, Yan P, Bai Y. Influences of temperature on mechanical properties of cement asphalt mortars. Mater Struct. 2014;47(1):285–92.10.1617/s11527-013-0060-2 ↗
20. Zhang Y, Kong X, Hou S, Liu Y, Han S. Study on the rheological properties of fresh cement asphalt paste. Constr Build Mater. 2012;27(1):534–44.10.1016/j.conbuildmat.2011.07.010 ↗
21. M.o.R. Dept. of Sci & Tech. Tentative specifications for cement-emulsified asphalt mortars used in CRTS II ballastless slab tracks of passenger-dedicated lines. Beijing, P. R China: China Railway Press; 2008.
22. Neville AM, Properties of concrete, 4th edition ed., Pearson education limited, Essex, 1999.
23. Yang J, Yan P, Kong X, Li X. Study on the hardening mechanism of cement asphalt binder. Sci China: Technol Sci. 2010;53(3):1406–12.10.1007/s11431-010-0010-y ↗
24. Hu S, Wang T, Wang F, Liu Z. Adsorption behaviour between cement and asphalt emulsion in cement-asphalt mortar. Adv Cem Res. 2009;21(1):11–4.10.1680/adcr.2007.00034 ↗
25. Poel V, Der C. A general system describing the visco-elastic properties of bitumens and its relation to routine test data. J Appl Chem. 1954;4(5):221–36.10.1002/jctb.5010040501 ↗
26. Cheung C, Cebon D. Deformation mechanisms of pure bitumen. J Mater Civ Eng. 1997;9(3):117–29.10.1061/(ASCE)0899-1561(1997)9:3(117) ↗
27. Cheung C, Cebon D. Experimental study of pure bitumens in tension, compression, and shear. J Rheol. 1997;41(1):45–74.10.1122/1.550858 ↗
28. Powers TC, Brownyard TL, Studies of the physical properties of hardened Portland cement paste, ACI Journal Proceedings, ACI, 1946.
29. Brouwers H. The work of powers and brownyard revisited: part 1. Cem Concr Res. 2004;34(9):1697–716.10.1016/j.cemconres.2004.05.031 ↗
30. Brouwers H. The work of powers and brownyard revisited: part 2. Cem Concr Res. 2005;35(10):1922–36.10.1016/j.cemconres.2005.04.009 ↗
31. Brouwers H, The work of powers and brownyard revisited: part 3, Proceedings of 12th international cogress on the chemistry of cement, montreal, Canada, 2007.
32. Lesueur D. The colloidal structure of bitumen: consequences on the rheology and on the mechanisms of bitumen modification. Adv Coll Interface Sci. 2009;145(1):42–82.10.1016/j.cis.2008.08.011 ↗