Parameter optimization and compressive property of the TC31 titanium alloy X-type lattice structure by the superplastic forming/diffusion bonding process
Source abstract
Abstract
The superplastic forming and diffusion bonding (SPF/DB) process was investigated for the manufacture of the TC31 titanium alloy X-type lattice structure. The finite element (FE) model was used to simulate the SPF process and compression behavior of the X-type lattice structure, and the deformation and compression failure modes were analyzed. A theoretical model was revised to predict the structural compressive strength. The results showed that the material processed by heat treatment still had great plasticity with the maximum elongation of 142.5% at 920 °C. The bonding rate, thinning rate and shear strength of the TC31 alloy joint bonded at 920 °C/3 MPa/60 min were 97.1%, 5.56% and 364 MPa, respectively, which indicated it was suitable for the X-type lattice truss structure to formed in the process parameter. Based on the result of the fundamental test and FE simulation, the X-type lattice structure could be fabricated by DB at 920 °C/3 MPa/60 min and SPF at 920 °C with a target strain rate of 0.001 s–1. Thickness measurements indicated that the area with a maximum thinning rate of 32.9% was located at the transition filet between the bonding areas and the ribs. The surface compressive strength of the X-type lattice structure was 1.51 MPa with a relative density of 0.015 when rib width was 5 mm, and the rib plastic buckling was considered as the failure mode of the TC31 titanium alloy lattice structure formed by SPF/DB. The surface compressive strength of the simulation results is 1.59 MPa with an error of 5.3%. The decrease of material properties and rib local thinning affect the accuracy of the theoretical predictions, and the revised theoretical result is 1.52 MPa with an error of 0.7%.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Cellular and Composite Structures · High-Velocity Impact and Material Behavior · Additive Manufacturing and 3D Printing Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (34)
Show source-provided references
1. Burkhart ET, Hefti L. Advancements of superplastic forming and diffusion bonding of titanium alloys for heat critical aerospace applications. SAE Int J Advances Curr Prac in Mobility. 2020;2(3):1202–8. https://doi.org/10.4271/2020-01-0033.10.4271/2020-01-0033 ↗
2. Queheillalt DT, Wadley HNG. Titanium alloy lattice truss structures. Mater Des. 2009;30(6):1966–75. https://doi.org/10.1016/j.matdes.2008.09.015.10.1016/j.matdes.2008.09.015 ↗
3. Zhao Z, Hou J, Fu Y. Measurement-based modal analysis and stability prediction on turn-milling of hollow turbine blade. Shock Vib. 2020;1:1–9. https://doi.org/10.1155/2020/8861373.10.1155/2020/8861373 ↗
4. Li ZQ, Guo HP. Application progress and development trend of superplastic forming/diffusion bonding technology. Aero manuf technol. 2010;8:32–5. https://doi.org/10.3969/j.issn.1671-833X.2010.08.003.10.3969/j.issn.1671-833X.2010.08.003 ↗
5. Zheng T, Yan H, Li S, et al. Compressive behavior and failure modes of the wood-based double X-type lattice sandwich structure. J Build Eng. 2020;30:101176. https://doi.org/10.1016/j.jobe.2020.101176.10.1016/j.jobe.2020.101176 ↗
6. Huang YJ, Xue YY, Wang XF, et al. Mechanical behavior of three-dimensional pyramidal aluminum lattice materials. Mater Sci Eng A. 2017;696:520–8. https://doi.org/10.1016/j.msea.2017.04.053.10.1016/j.msea.2017.04.053 ↗
7. Zhang Q, Jiang WC, Zhao B, et al. A study of the effective elastic modulus of a lattice truss panel structure by experimental and theoretical analysis. Comp Struct. 2017;165:130–7. https://doi.org/10.1016/j.compstruct.2017.01.012.10.1016/j.compstruct.2017.01.012 ↗
8. Zhang QC, Han YJ, Chen CQ, et al. Ultralight X-type lattice sandwich structure (I): concept, fabrication and experimental characterization. Sci China Ser E. 2009;52(8):2147–54. https://doi.org/10.1007/s11431-009-0219-9.10.1007/s11431-009-0219-9 ↗
9. Jiang W, Chen H, Gong JM, et al. Numerical modelling and nanoindentation experiment to study the brazed residual stresses in an X-type lattice truss sandwich structure. Mater Sci Eng A. 2011;528(13–14):4715–22. https://doi.org/10.1016/j.msea.2011.02.073.10.1016/j.msea.2011.02.073 ↗
10. Wang B, Hu J, Li Y, et al. Mechanical properties and failure behavior of the sandwich structures with carbon fiber-reinforced X-type lattice truss core. Comp Struct. 2018;185:619–33. https://doi.org/10.1016/j.compstruct.2017.11.066.10.1016/j.compstruct.2017.11.066 ↗
11. Wadley HNG. Multifunctional periodic cellular metals. Philos T R Soc A. 1838;2006(364):31–68. https://doi.org/10.1098/rsta.2005.1697.10.1098/rsta.2005.1697 ↗
12. Gregory WK, Vikram SD, Haydn NGW. Compressive behavior of age hardenable tetrahedral lattice truss structures made from aluminium. Acta Mater. 2004;52(14):4229–37. https://doi.org/10.1016/j.actamat.2004.05.039.10.1016/j.actamat.2004.05.039 ↗
13. Liu ZB, Chen HT, Xing SQ. Mechanical performances of metal-polymer sandwich structures with 3D-printed lattice cores subjected to bending load. Arch Civ Mech Eng. 2020;20(3):89. https://doi.org/10.1007/s43452-020-00095-1.10.1007/s43452-020-00095-1 ↗
14. Li X, Wang GF, Zhang JX, et al. Electrically assisted superplastic forming/diffusion bonding of the Ti2AlNb alloy sheet. Int J Adv Manuf Technol. 2020;106(1–2):77–89. https://doi.org/10.1007/s00170-019-04458-8.10.1007/s00170-019-04458-8 ↗
15. Du ZH, Wang CX, Liu Q, et al. The superplastic forming/diffusion bonding of TA7 titanium alloy for manufacturing hollow structure with stiffeners. J Manuf Process. 2022;73:385–94. https://doi.org/10.1016/j.jmapro.2021.10.064.10.1016/j.jmapro.2021.10.064 ↗
16. Langdon TG. Forty-five years of superplastic research: recent developments and future prospects. Mater Sci Forum. 2016;838–839:3–12. https://doi.org/10.4028/www.scientific.net/MSF.838-839.3.10.4028/www.scientific.net/MSF.838-839.3 ↗
17. Wu Y, Wu D, Ma J, et al. A physically based constitutive model of Ti-6Al-4 V and application in the SPF/DB process for a pyramid lattice sandwich panel. Arch Civ Mech Eng. 2021. https://doi.org/10.1007/S43452-021-00260-0.10.1007/S43452-021-00260-0 ↗
18. Tan ZL, Bai LS, Bai BZ, et al. Fabrication of lattice truss structures by novel super-plastic forming and diffusion bonding process in a titanium alloy. Mater Des. 2016;92:724–30. https://doi.org/10.1016/j.matdes.2015.12.100.10.1016/j.matdes.2015.12.100 ↗
19. Li ZQ, Zhao B, Shao J, et al. Deformation behavior and mechanical properties of periodic topological Ti structures fabricated by superplastic forming/diffusion bonding. Int J Lightw Mater Manuf. 2019;2(1):1–30. https://doi.org/10.1016/j.ijlmm.2018.11.001.10.1016/j.ijlmm.2018.11.001 ↗
20. Zhang T, Sha Hp, Li L, et al. Study of macroscopic defects of four-layer structure of Ti–6Al–4V during superplastic forming/diffusion bonding. Int J Precis Eng Manuf. 2021;22(1):27–39. https://doi.org/10.1007/s12541-020-00432-7.10.1007/s12541-020-00432-7 ↗
21. Chang-Wen W, Tao Z, Guofeng W, et al. Superplastic forming and diffusion bonding of Ti–22Al–24Nb alloy. J Mater Process Tech. 2015;222:122–7. https://doi.org/10.1016/j.jmatprotec.2015.03.005.10.1016/j.jmatprotec.2015.03.005 ↗
22. Du ZH, Jiang SS, Zhang KF, et al. The structural design and superplastic forming/diffusion bonding of Ti2AlNb based alloy for four-layer structure. Mater Des. 2016;104:242–50. https://doi.org/10.1016/j.matdes.2016.05.046.10.1016/j.matdes.2016.05.046 ↗
23. Cheng J, Lee S. Methods for resolving grooving problems in parts manufactured from combined diffusion bonding and superplastic forming processes. J Mater Process Technol. 1994;45(1–4):249–54. https://doi.org/10.1016/0924-0136(94)90348-4.10.1016/0924-0136(94)90348-4 ↗
24. Li BY, Zhang JT, Zhang KF, et al. Research on control method of surface groove of titanium alloy SPF/DB Four-sheet structure. Aero Manuf Technol. 2020;63(21):63–7.
25. Wu DP, Wu Y, Chen MH, et al. Research on high temperature flow behavior and microstructure evolution of TC31 titanium alloy sheets. Rare Met Mater Eng. 2019;48(12):3901–10.
26. Peng Y, Li JL, Li ZX, et al. Interfacial voids and microstructure evolution, bonding behavior and deformation mechanism of TC4 diffusion bonded joints. J Manuf Process. 2022;81:837–51. https://doi.org/10.1016/J.JMAPRO.2022.07.037.10.1016/j.jmapro.2022.07.037 ↗
27. Wu HP, Li XF, Mei QF, et al. Flow behavior of diffusion bonding interface of Ti6Al4V alloy over a wide range of strain rates. Mater Sci Eng A. 2019;761:138067. https://doi.org/10.1016/j.msea.2019.138067.10.1016/j.msea.2019.138067 ↗
28. Chen HL, Zheng Q, Zhao L, et al. Mechanical property of lattice truss material in sandwich panel including strut flexural deformation. Compos Struct. 2012;94(12):3448–56. https://doi.org/10.1016/j.compstruct.2012.06.004.10.1016/j.compstruct.2012.06.004 ↗
29. Yin Q, Soyarslan C, Güner A, et al. A cyclic twin bridge shear test for the identification of kinematic hardening parameters. Int J Mech Sci. 2012;59(1):31–43. https://doi.org/10.1016/j.ijmecsci.2012.02.008.10.1016/j.ijmecsci.2012.02.008 ↗
30. Pamela A. Finite element analysis and validation of the superplastic forming of multi-sheet structures. Mater Sci Forum. 2016;4248(838–839):621–6. https://doi.org/10.4028/www.scientific.net/MSF.838-839.621.10.4028/www.scientific.net/MSF.838-839.621 ↗
31. Liu ZQ, Wang XS, Jiao XY, et al. Prediction of microstructure evolution during hot gas forming of Ti 2 AlNb-based alloy tubular component with square cross-section. Procedia Manuf. 2018;15:1156–63. https://doi.org/10.1016/j.promfg.2018.07.374.10.1016/j.promfg.2018.07.374 ↗
32. K. C, C. S S, B. B S, et al. Superplastic forming with diffusion bonding of titanium alloys. Mater Today 2020;27(3):2909–13. https://doi.org/10.1016/j.matpr.2020.03.51410.1016/j.matpr.2020.03.514 ↗
33. Xiong J, Ma L, Vaziri A, et al. Mechanical behavior of carbon fiber composite lattice core sandwich panels fabricated by laser cutting. Acta Mater. 2012;60(13–14):5322–34. https://doi.org/10.1016/j.actamat.2012.06.004.10.1016/j.actamat.2012.06.004 ↗
34. Wang XX, Wang WQ, Ma HM. Microstructure and mechanical properties of high temperature and high strength BTi-6431S alloy at 700 °C. Chin J Nonferr Met. 2010;20:792–5.