journal article·2021-11-12Open access

Characterization of ultrafine-grained copper joints acquired by rotary friction welding

M. Ciemiorek, Ł. Morawiński, C. Jasiński, M. Orłowska, T. Chmielewski, L. Olejnik, M. Lewandowska

Abstract

Abstract Copper rods with ultrafine-grained microstructure, obtained by multi-turn ECAP processing, were subjected to Direct Drive Rotary Friction Welding using various processing parameters, such as rotational speed and pressure, which resulted in different energy and heat input. Even though friction welding is a high energy process, by a proper selection of processing parameters it was possible to maintain grain size at around 0.7 µm in the weld zone and preserve the UFG microstructure. These microstructural features translated into mechanical properties: the YS for those specimens was around 330 MPa. Processing parameters that resulted in a larger heat input caused an increase in grain size to around 2 µm; this, however, increased ductility and led to a uniform elongation exceeding 5%. Corrosion resistance in the stir zone increased, as was evident in the higher open circuit potential and higher corrosion potential in comparison with base material; the observed differences were about 50 mV. These changes can be explained by the higher fraction of HAGBs in the SZ.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Microstructure and mechanical properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (49)

Show source-provided references
1. Segal V. Equal-channel angular extrusion (ECAE): from a laboratory curiosity to an industrial technology. Metals (Basel). 2020;10:244.10.3390/met10020244 ↗
2. Li W, Vairis A, Preuss M, Ma T. Linear and rotary friction welding review. Int Mater Rev. 2016;61:71–100. https://doi.org/10.1080/09506608.2015.1109214.10.1080/09506608.2015.1109214 ↗
3. Nicholas ED. Friction Processing Technologies. Weld World. 2003;47:2–9.10.1007/BF03266402 ↗
4. Mirzadeh H. High strain rate superplasticity via friction stir processing (FSP): A review. Mater Sci Eng A. 2021;819: 141499. https://doi.org/10.1016/j.msea.2021.141499.10.1016/j.msea.2021.141499 ↗
5. Kwon Y, Saito N, Shigematsu I. Friction stir process as a new manufacturing technique of ultrafine grained aluminum alloy. J Mater Sci Lett. 2002;21:1473–6.10.1023/A:1020067609451 ↗
6. Fujii H, Ueji R, Takada Y, Kitahara H, Tsuji N, Nakata K, Nogi K. Friction stir welding of ultrafine grained interstitial free steels. Mater Trans. 2006;47:239–42.10.2320/matertrans.47.239 ↗
7. Malopheyev S, Mironov S, Kulitskiy V, Kaibyshev R. Friction-stir welding of ultra-fine grained sheets of Al–Mg–Sc–Zr alloy. Mater Sci Eng A. 2015;624:132–9. https://doi.org/10.1016/j.msea.2014.11.079.10.1016/j.msea.2014.11.079 ↗
8. Sahin M, Akata HE, Ozel K. An experimental study on joining of severe plastic deformed aluminium materials with friction welding method. Mater Des. 2008;29:265–74. https://doi.org/10.1016/j.matdes.2006.11.004.10.1016/j.matdes.2006.11.004 ↗
9. Zhang B, Yuan S, Wang X. Friction stir welding of AZ31 magnesium alloys processed by equal channel angular. Rare Met. 2008;27:393–9.10.1016/S1001-0521(08)60151-5 ↗
10. Sato YS, Urata M, Kokawa H, Ikeda K. Hall-Petch relationship in friction stir welds of equal channel angular-pressed aluminium alloys. Mater Sci Eng A. 2003;354:298–305. https://doi.org/10.1016/S0921-5093(03)00008-X.10.1016/S0921-5093(03)00008-X ↗
11. Ouyang J, Yarrapareddy E, Kovacevic R. Microstructural evolution in the friction stir welded 6061 aluminum alloy (T6-temper condition ) to copper. J Mater Process Technl. 2006;172:110–22. https://doi.org/10.1016/j.jmatprotec.2005.09.013.10.1016/j.jmatprotec.2005.09.013 ↗
12. Barekatain H, Kazeminezhad M, Kokabi AH. Microstructure and mechanical properties in dissimilar butt friction stir welding of severely plastic deformed aluminum AA 1050 and commercially pure copper sheets. J Mater Sci Technol. 2014;30:826–34. https://doi.org/10.1016/j.jmst.2013.11.007.10.1016/j.jmst.2013.11.007 ↗
13. Xue P, Wang BB, Chen FF, Wang WG, Xiao BL, Ma ZY. Microstructure and mechanical properties of friction stir processed Cu with an ideal ultra fi ne-grained structure. Mater Charact. 2016;121:187–94. https://doi.org/10.1016/j.matchar.2016.10.009.10.1016/j.matchar.2016.10.009 ↗
14. Prangnell PB, Bowen JR, Apps PJ. Ultra-fine grain structures in aluminium alloys by severe deformation processing. Mater Sci Eng A. 2004;375–377:178–85.10.1016/j.msea.2003.10.170 ↗
15. Su J, Nelson TW, Sterling CJ. Friction stir processing of large-area bulk UFG aluminum alloys. Scr Mater. 2005;52:135–40. https://doi.org/10.1016/j.scriptamat.2004.09.014.10.1016/j.scriptamat.2004.09.014 ↗
16. Xie GM, Ma ZY, Geng L. Development of a fine-grained microstructure and the properties of a nugget zone in friction stir welded pure copper. Scr Mater. 2007;57:73–6. https://doi.org/10.1016/j.scriptamat.2007.03.048.10.1016/j.scriptamat.2007.03.048 ↗
17. Xu N, Song Q, Bao Y, Jiang Y, Shen J. Achieving good strength-ductility synergy of friction stir welded Cu joint by using large load with extremely low welding speed and rotation rate. Mater Sci Eng A. 2017;687:73–81. https://doi.org/10.1016/j.msea.2017.01.052.10.1016/j.msea.2017.01.052 ↗
18. Xue P, Xiao BL, Zhang Q, Ma ZY. Achieving friction stir welded pure copper joints with nearly equal strength to the parent metal via additional rapid cooling. Scr Mater. 2011;64:1051–4. https://doi.org/10.1016/j.scriptamat.2011.02.019.10.1016/j.scriptamat.2011.02.019 ↗
19. Davari H, Parsa MH, Hadian AM, Ahmadabadi MN, Davari H, Parsa MH, Hadian AM, Ahmadabadi MN. Experimental and numerical thermomechanical analysis of hybrid friction welding of commercially pure copper bars experimental and numerical thermomechanical analysis of hybrid friction welding of commercially pure copper bars. Mater Manuf Process. 2011;26:694–702. https://doi.org/10.1080/10426914.2010.480993.10.1080/10426914.2010.480993 ↗
20. Uday MB, Fauzi MNA, Zuhailawati H, Ismail AB. Advances in friction welding process: a review. Sci Technol Weld Join. 2010;15:534–59. https://doi.org/10.1179/136217110X12785889550064.10.1179/136217110X12785889550064 ↗
21. Yang Y, Chen W, Lee H. A nonlinear inverse problem in estimating the heat generation in rotary friction welding. Numer Heat Transf Part A Appl Int J Comput Methodol. 2011;59(2):130–49. https://doi.org/10.1080/10407782.2011.540965.10.1080/10407782.2011.540965 ↗
22. Rosochowski A, Olejnik L. Numerical and physical modelling of plastic deformation in 2-turn equal channel angular extrusion. J Mater Process Technol. 2002;126:309–16.10.1016/S0924-0136(02)00339-4 ↗
23. Olejnik L, Rosochowski A. Scaled-up ECAP with enhanced productivity. Steel Res Int. 2008;2:439–47.
24. Lipińska M, Olejnik L, Lewandowska M. The influence of an ECAP-based deformation process on the microstructure and properties of electrolytic tough pitch copper. Metals (Basel). 2018;53:3862–75. https://doi.org/10.1007/s10853-017-1814-y.10.1007/s10853-017-1814-y ↗
25. Rosochowski A. Severe plastic deformation technology. Dunbeath: Whittles Publishing; 2017.
26. Morawiński Ł, Jasiński C, Ciemiorek M, Chmielewski T, Olejnik L, Lewandowska M. Solid-state welding of ultrafine grained copper rods. Arch Civ Mech Eng. 2021;21:89. https://doi.org/10.1007/s43452-021-00244-0.10.1007/s43452-021-00244-0 ↗
27. Mishra A, Kad BK, Gregori F, Meyers MA. Microstructural evolution in copper subjected to severe plastic deformation: experiments and analysis. Acta Mater. 2007;55:13–28.10.1016/j.actamat.2006.07.008 ↗
28. Molodova X, Gottstein G, Winning M, Hellmig RJ. Thermal stability of ECAP processed pure copper. Mater Sci Eng A. 2007;461:204–13.10.1016/j.msea.2007.01.042 ↗
29. Sakai T, Belyakov A, Kaibyshev R, Miura H, Jonas JJ. Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions. Prog Mater Sci. 2014;60:130–207. https://doi.org/10.1016/j.pmatsci.2013.09.002.10.1016/j.pmatsci.2013.09.002 ↗
30. Heidarzadeh A, Mironov S, Kaibyshev R, Çam G, Simar A, Gerlich A, Withers J. Friction stir welding/processing of metals and alloys : A comprehensive review on microstructural evolution. Prog Mater Sci. 2021;117: 100752. https://doi.org/10.1016/j.pmatsci.2020.100752.10.1016/j.pmatsci.2020.100752 ↗
31. Patel V, Li W, Vairis A, Badheka V. Recent development in friction stir processing as a solid-state grain refinement technique: microstructural evolution and property enhancement recent development in friction stir processing as a solid-state grain refinement technique: microstructural evolution and property enhancement. Crit Rev Solid State Mater Sci. 2019;44:378–426. https://doi.org/10.1080/10408436.2018.1490251.10.1080/10408436.2018.1490251 ↗
32. Xue P, Wang BB, Chen FF, Wang WG, Xiao BL, Ma ZY. Microstructure and mechanical properties of friction stir processed Cu with an ideal ultra fine-grained structure. Mater Charact. 2016;121:187–94. https://doi.org/10.1016/j.matchar.2016.10.009.10.1016/j.matchar.2016.10.009 ↗
33. Li W, Wang F. Modeling of continuous drive friction welding of mild steel. Mater Sci Eng A. 2011;528:5921–6. https://doi.org/10.1016/j.msea.2011.04.001.10.1016/j.msea.2011.04.001 ↗
34. Maalekian M, Kozeschnik E, Brantner HP, Cerjak H. Comparative analysis of heat generation in friction welding of steel bars. Acta Mater. 2008;56:2843–55. https://doi.org/10.1016/j.actamat.2008.02.016.10.1016/j.actamat.2008.02.016 ↗
35. Duffin FD, Bahrani A. Frictional behaviour of mild steel in friction welding. Wear. 1973;26:53–74.10.1016/0043-1648(73)90150-6 ↗
36. Jata KV, Semiatin SL. Continuous dynamic recrystallization during friction stir welding of high strength aluminium alloys. Scr Mater. 2000;43:743–9.10.1016/S1359-6462(00)00480-2 ↗
37. Su J, Nelson TW, Mishra R, Mahoney M. Microstructural investigation of friction stir welded 7050–T651 aluminium. Acta Mater. 2003;51:713–29. https://doi.org/10.1016/S1359-6454(02)00449-4.10.1016/S1359-6454(02)00449-4 ↗
38. Meyers MA, Mishra A, Benson DJ. Mechanical properties of nanocrystalline materials. Prog Mater Sci. 2006;51:427–556. https://doi.org/10.1016/j.pmatsci.2005.08.003.10.1016/j.pmatsci.2005.08.003 ↗
39. Barenji RV. Influence of heat input conditions on microstructure evolution and mechanical properties of friction stir welded pure copper joints. Trans Indian Inst Met. 2016;69:1077–85. https://doi.org/10.1007/s12666-015-0624-7.10.1007/s12666-015-0624-7 ↗
40. Farrokhi H, Heidarzadeh A, Saeid T. Frictions stir welding of copper under different welding parameters and media. Sci Technol Weld Join. 2013;18:697–702. https://doi.org/10.1179/1362171813Y.0000000148.10.1179/1362171813Y.0000000148 ↗
41. Xu N, Ueji R, Fujii H. Enhanced mechanical properties of 70/30 brass joint by rapid cooling friction stir welding. Mater Sci Eng A. 2014;610:132–8. https://doi.org/10.1016/j.msea.2014.05.037.10.1016/j.msea.2014.05.037 ↗
42. Tasic ZZ, Petrovic Mihajlovic MB, Radovanovic MB, Simonovic AT, Antonijevic MM. Cephradine as corrosion inhibitor for copper in 0.9% NaCl solution. J Mol Struct. 2018;1159:46–54. https://doi.org/10.1016/j.molstruc.2018.01.031.10.1016/j.molstruc.2018.01.031 ↗
43. Song D, Ma A, Sun W, Jiang J, Jiang J, Yang D, Guo G. Improved corrosion resistance in simulated concrete pore solution of surface nanocrystallized rebar fabricated by wire-brushing. Corros Sci. 2014;82:437–41. https://doi.org/10.1016/j.corsci.2014.01.034.10.1016/j.corsci.2014.01.034 ↗
44. Ralston KD, Birbilis N. Effect of grain size on corrosion: a REVIEW. Corrosion. 2010;66:1–4. https://doi.org/10.5006/1.3462912.10.5006/1.3462912 ↗
45. Vinogradov A, Mimaki T, Hashimoto S, Valiev R. On the corrosion behaviour of ultra-fine grain copper. Scr Mater. 1999;41:319–26.10.1016/S1359-6462(99)00170-0 ↗
46. Xu XX, Nie FL, Zhang JX, Zheng W, Zheng YF, Hu C, Yang G. Corrosion and ion release behavior of ultra-fi ne grained bulk pure copper fabricated by ECAP in Hanks solution as potential biomaterial for contraception. Mater Lett. 2010;64:524–7. https://doi.org/10.1016/j.matlet.2009.11.065.10.1016/j.matlet.2009.11.065 ↗
47. Fattah-alhosseini A, Taheri AH. Effect of friction stir welding on corrosion behavior of pure copper in 3.5wt.% NaCl solution. J Manuf Process. 2015;20:98–103. https://doi.org/10.1016/j.jmapro.2015.09.005.10.1016/j.jmapro.2015.09.005 ↗
48. Xia T, Zeng L, Zhang X, Liu J, Zhang W, Liang T. Enhanced corrosion resistance of a Cu e 10Ni alloy in a 3.5 wt % NaCl solution by means of ultrasonic surface rolling treatment. Surf Coat Technol. 2019;363:390–9. https://doi.org/10.1016/j.surfcoat.2019.02.039.10.1016/j.surfcoat.2019.02.039 ↗
49. Chukwuike VI, Echem OG, Prabhakaran S, Anandkumar S, Barik RC. Laser shock peening (LSP): electrochemical and hydrodynamic investigation of corrosion protection pre-treatment for a copper surface in 3.5 % NaCl medium. Corros Sci. 2021;179:109156. https://doi.org/10.1016/j.corsci.2020.109156.10.1016/j.corsci.2020.109156 ↗