journal article·2025-08-29Open access

High strain rate response of CP-titanium under low-temperature conditions: experiment and modeling

Mateusz Kopec, Magdalena Łazińska, Jacek Janiszewski

Abstract

Abstract This study investigates the dynamic mechanical behavior and microstructural evolution of commercially pure titanium (CP-Ti) under high-strain-rate loading at subzero temperature. Using a Split Hopkinson Pressure Bar setup equipped with a cryogenic environmental chamber, CP-Ti specimens were dynamically compressed at − 100 °C across strain rates of 1 × 103 s−1 and 2 × 103 s−1. The results show a significant increase in flow stress at − 100 °C compared to room temperature, with peak true stresses reaching approximately 825 MPa at 2 × 103 s−1 and 730 MPa at 1 × 103 s−1 representing ~ 25–30% higher values than those observed at 22 °C. Electron backscatter diffraction analysis revealed a transition in deformation mechanisms with increasing strain rate and decreasing temperature. At room temperature, plastic deformation was predominantly accommodated by dislocation slip and deformation twinning. At low temperature, while twinning activity intensified, it was eventually superseded by shear band formation, indicating the onset of strain localization. A physically based viscoplastic constitutive model incorporating dislocation density evolution and thermally activated mechanisms was developed and calibrated against experimental data. The model accurately captured the stress–strain behavior across all tested conditions, with deviations below 5%, demonstrating its suitability for predictive simulations of low-temperature forming processes in HCP metals.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: High-Velocity Impact and Material Behavior · Energetic Materials and Combustion · Ion-surface interactions and analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. Xu Y, Aceves Lopez M, Zhou J, Farbaniec L, Patsias S, Macdougall D, et al. Experimental analysis of the multiaxial failure stress locus of commercially pure titanium at low and high rates of strain. Int J Impact Eng. 2022;170:104341. https://doi.org/10.1016/j.ijimpeng.2022.104341.10.1016/j.ijimpeng.2022.104341 ↗
2. Wei Y, Zhang C, Yuan Y, Chen P, Huang C, Li J, et al. Blast response of additive manufactured Ti–6Al–4V sandwich panels. Int J Impact Eng. 2023;176:104553. https://doi.org/10.1016/j.ijimpeng.2023.104553.10.1016/j.ijimpeng.2023.104553 ↗
3. Kopec M, Wang K, Politis DJ, Wang Y, Wang L, Lin J. Formability and microstructure evolution mechanisms of Ti6Al4V alloy during a novel hot stamping process. Mater Sci Eng A. 2018;719:72–81. https://doi.org/10.1016/j.msea.2018.02.038.10.1016/j.msea.2018.02.038 ↗
4. Bao Q, Zhao C, Wang K, Zhao J, Cui S, Gao B, et al. A novel integrated hot forming with in-situ stress relaxation-aging for titanium alloy thin-walled components. J Manuf Process. 2024;131:1296–308. https://doi.org/10.1016/j.jmapro.2024.09.113.10.1016/j.jmapro.2024.09.113 ↗
5. Wang K, Kopec M, Chang S, Qu B, Liu J, Politis DJ, et al. Enhanced formability and forming efficiency for two-phase titanium alloys by fast light alloys stamping technology (FAST). Mater Des. 2020;108948:1–25. https://doi.org/10.1016/j.matdes.2020.108948.10.1016/j.matdes.2020.108948 ↗
6. Wang K, Wang L, Zheng K, He Z, Politis DJ, Liu G, et al. High-efficiency forming processes for complex thin-walled titanium alloys components: state-of-the-art and perspectives. Int J Extrem Manuf. 2020;2:032001. https://doi.org/10.1088/2631-7990/ab949b.10.1088/2631-7990/ab949b ↗
7. Lei L, Zhu Q, Zhao Q, Yang M, Yang W, Zeng W, et al. Low-temperature impact toughness and deformation mechanism of CT20 titanium alloy. Mater Charact. 2023;195:112504. https://doi.org/10.1016/j.matchar.2022.112504.10.1016/j.matchar.2022.112504 ↗
8. Li D, Meng ZC, Shen YY, Zhang JH, Hu M, Qiu JK, et al. Study of low-temperature impact deformation behavior of Ti–6Al–4V alloy. Vacuum. 2024;222:113066. https://doi.org/10.1016/j.vacuum.2024.113066.10.1016/j.vacuum.2024.113066 ↗
9. Kopec M, Liu X, Gorniewicz D, Modrzejewski P, Zasada D, Jóźwiak S, et al. Mechanical response of 6061–T6 aluminium alloy subjected to dynamic testing at low temperature: experiment and modelling. Int J Impact Eng. 2024;185:104843. https://doi.org/10.1016/j.ijimpeng.2023.104843.10.1016/j.ijimpeng.2023.104843 ↗
10. Lin H, Jin G, Zhan Q, et al. Mechanical properties and constitutive model of TC4 titanium alloy at cryogenic. J Mater Eng Perform. 2024;33:13731–43. https://doi.org/10.1007/s11665-023-08955-6.10.1007/s11665-023-08955-6 ↗
11. Chong Y, Gholizadeh R, Tsuru T, et al. Grain refinement in titanium prevents low temperature oxygen embrittlement. Nat Commun. 2023;14:404. https://doi.org/10.1038/s41467-023-36030-0.10.1038/s41467-023-36030-0 ↗
12. Jeon B, Lee MS, Jun TS, Jeong Y. Temperature-dependent behavior of CP-Ti interpreted via self-consistent crystal plasticity simulation. Mater Sci Eng A. 2024;890:145904. https://doi.org/10.1016/j.msea.2023.145904.10.1016/j.msea.2023.145904 ↗
13. Lee MS, Jo AR, Hwang SK, Hyun YT, Jun TS. The role of strain rate and texture in the deformation of commercially pure titanium at cryogenic temperature. Mater Sci Eng A. 2021;827:142042. https://doi.org/10.1016/j.msea.2021.142042.10.1016/j.msea.2021.142042 ↗
14. Liu D, Yang D, Hou Y, Li Y, Wang G, Yi H. Strain rate effects on mechanical properties, microstructural evolution, and deformation mechanisms of high manganese steels. J Mater Sci Technol. 2025;237:219–55. https://doi.org/10.1016/j.jmst.2025.03.026.10.1016/j.jmst.2025.03.026 ↗
15. Yang H, Li H, Sun H, Zhang YH, Liu X, Zhan M, et al. Anisotropic plasticity and fracture of alpha titanium sheets from cryogenic to warm temperatures. Int J Plast. 2022;156:103348. https://doi.org/10.1016/j.ijplas.2022.103348.10.1016/j.ijplas.2022.103348 ↗
16. Chen C, Han D, Song Y, Wang M, Li Y, Xu S. Thermal stability of deformation twins in cryogenic rolled CP-Ti. Mater Charact. 2023;196:112587. https://doi.org/10.1016/j.matchar.2022.112587.10.1016/j.matchar.2022.112587 ↗
17. Tsukamoto G, Kunieda T, Mitsuhara M, Nakashima H. Effect of twinning deformation on work hardening in commercially pure titanium. Mater Sci Eng A. 2022;840:142907. https://doi.org/10.1016/j.msea.2022.142907.10.1016/j.msea.2022.142907 ↗
18. Guo Y, Ruan Q, Zhu S, Wei Q, Lu J, Hu B, et al. Dynamic failure of titanium: temperature rise and adiabatic shear band formation. J Mech Phys Solids. 2020;135:103811. https://doi.org/10.1016/j.jmps.2019.103811.10.1016/j.jmps.2019.103811 ↗
19. Chakraborty A, Roy S. Shear localization and shear banding: a review about the complex interplay between material, microstructural and process variables. Mater Charact. 2024;218:114501. https://doi.org/10.1016/j.matchar.2024.114501.10.1016/j.matchar.2024.114501 ↗
20. Garrett RP, Lin J, Dean TA. An investigation of the effects of solution heat treatment on mechanical properties for AA 6xxx alloys: experimentation and modelling. Int J Plast. 2005;21:1640–57. https://doi.org/10.1016/j.ijplas.2004.11.002.10.1016/j.ijplas.2004.11.002 ↗
21. Schneider R, Grant RJ, Sotirov N, Falkinger G, Grabner F, Reichl C, et al. Constitutive flow curve approximation of commercial aluminium alloys at low temperatures. Mater Des. 2015;88:659–66. https://doi.org/10.1016/j.matdes.2015.09.034.10.1016/j.matdes.2015.09.034 ↗
22. Lee W-S, Lin C-R. Deformation behavior and microstructural evolution of 7075–T6 aluminum alloy at cryogenic temperatures. Cryogenics. 2016;79:26–34. https://doi.org/10.1016/j.cryogenics.2016.07.007.10.1016/j.cryogenics.2016.07.007 ↗
23. Wang D, Xu Z, Han Y, Su M, Huang F. Coupled effect of stress state and strain rate on ductile fracture of Ti6Al4V alloy. Int J Impact Eng. 2024;187:104898. https://doi.org/10.1016/j.ijimpeng.2024.104898.10.1016/j.ijimpeng.2024.104898 ↗
24. Zhou T, Wu J, Che J, Wang Y, Wang X. Dynamic shear characteristics of titanium alloy Ti–6Al–4V at large strain rates by the split Hopkinson pressure bar test. Int J Impact Eng. 2017;109:167–77. https://doi.org/10.1016/j.ijimpeng.2017.06.007.10.1016/j.ijimpeng.2017.06.007 ↗