Impact of feed rate and arc power in wire arc additive manufacturing of AISI 308L stainless steel
Source abstract
Abstract
In this study, the process of wire arc additive manufacturing (WAAM) by cold metal transfer (CMT) operation has been investigated for AISI 308L austenitic stainless steel. The wire feeder rate (WFR) was set between 3.5 and 7.0 m/min, while the current ranged from 72 to 115 A and the voltage from 11.1 to 12.6 V, as determined by the generator. Additionally, the robot speed was maintained at 7 mm/min for all samples. Microstructural and mechanical analyses have been conducted to improve the dilution area by considering having a different range of the width of the deposited part. Optical microscopy (OM) has been used for scanning the cross-section of the fabricated parts, and scanning electron microscopy (SEM), together with electron back scatter diffraction (EBSD), for monitoring the microstructure of the substrate, heat-affected zone (HAZ), and deposited metal. Energy-dispersive X-ray (EDX) analysis was applied to reveal the dilution area. Moreover, to link the oxidation of the peak deposition to the surface roughness, a focused ion beam (FIB) was used to remove a tiny volume of the peak surface. The results indicate that increasing the voltage and current in the WAAM process directly influences both microhardness and bead width. Microhardness reached up to 310 HV in the heat-affected zone (HAZ), while the width of the deposited bead increased from 2.9 mm at 799 W to 6.2 mm at 1449 W. Additionally, surface roughness along the deposited lines decreased with a higher wire feeder rate, with the lowest roughness recorded at 20.1 µm. Finally, FIB analysis revealed that the oxide layer was approximately 1 µm thick, with chromium penetration observed within the layer.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · Advanced Machining and Optimization Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (53)
Show source-provided references
1. Kahhal P, Jo YK, Park SH. Recent progress in remanufacturing technologies using metal additive manufacturing processes and surface treatment. Int J Precis Eng Manuf-Green Technol. 2024;11(2):625–58.10.1007/s40684-023-00551-2 ↗
2. Manurung YH, Prajadhiana KP, Adenan MS, Awiszus B, Graf M, Haelsig A. Analysis of material property models on WAAM distortion using nonlinear numerical computation and experimental verification with P-GMAW. Arch Civil Mech Eng. 2021;21:1–13.10.1007/s43452-021-00189-4 ↗
3. Karamimoghadam M, Rezayat M, Contuzzi N, Denora V, Mateo A, Casalino G. Effect of wire feed rate on ER70S-6 microstructure of wire arc additive manufacturing process. Int J Adv Manuf Technol. 2025;137(5):2947–61.10.1007/s00170-025-15334-z ↗
4. Korniejenko K, Gądek S, Dynowski P, Tran DH, Rudziewicz M, Pose S, Grab T. Additive manufacturing in underwater applications. Appl Sci. 2024;14(4):1346.10.3390/app14041346 ↗
5. Kannan AR, Pramod R, Prakash KS, Shanmugam NS, Yoon J, Oliveira JP. Understanding the microstructural evolution and fatigue behavior of aluminum 2319 fabricated by wire arc additive manufacturing. Arch Civil Mech Eng. 2024;24(2):110.10.1007/s43452-024-00925-6 ↗
6. Capasso I, Andreacola FR, Brando G. Additive manufacturing of metal materials for construction engineering: an overview on technologies and applications. Metals. 2024;14(9):1033.10.3390/met14091033 ↗
7. Yuan, K., Xu, Y., Wang, X., Ma, X., Wang, Q. and Zhang, H., 2024. Key Technologies and Research Progress in Robotic Arc Additive Remanufacturing. Sensors and Actuators A: Physical, p.115547.10.1016/j.sna.2024.115547 ↗
8. Zhang H, Peng K, Chen X. Duplex stainless steel 2209 with excellent properties deposited by plasma arc additive manufacturing without post heat-treatment: favorable phase ratio and no σ-phase. Arch Civil Mech Eng. 2024;24(3):175.10.1007/s43452-024-00907-8 ↗
9. Paul C, Nath D, Tobber L, Benoit M. Review of opportunities and challenges for additive manufacturing of steels in the construction industry. Adv Civil Eng Mater. 2024;13(1):232–47.10.1520/ACEM20230097 ↗
10. Delfino, F.H.S., Koga, G.Y., F. Cavalcante, T.R., Bon, D., Giarola, J., Shen, J., Oliveira, J.P., Lopes, É.S.N. and Avila, J.A., 2024. Mechanical and corrosion characteristics of heat-treated wire arc additive manufactured parts of Inconel® 625 superalloy. Progress in Additive Manufacturing, pp.1–21.10.1007/s40964-024-00772-0 ↗
11. Mattera G, Caggiano A, Nele L. Optimal data-driven control of manufacturing processes using reinforcement learning: an application to wire arc additive manufacturing. J Intell Manuf. 2024;36(2):1291–310. https://doi.org/10.1007/s10845-023-02307-w.10.1007/s10845-023-02307-w ↗
12. Karamimoghadam, M., Aghayar, Y., Forooghi, F., Mohammadi, M., Contuzzi, N. and Casalino, G., 2024, August. Effect of Manufacturing Strategy on Microstructure of a Low-Carbon Steel Alloy Fabricated with Wire-Arc Additive Manufacturing. In Conference of Metallurgists (pp. 109–112). Cham: Springer Nature Switzerland.10.1007/978-3-031-67398-6_23 ↗
13. Kannan AR, Rajkumar V, Vasudevan SV, Jerome P, Oh TH. Microstructure, hardness, and electrical resistivity of Al-Cu alloy fabricated via wire arc additive manufacturing. Mater Today Commun. 2024;39:108582.10.1016/j.mtcomm.2024.108582 ↗
14. Teng S, Dehgahi S, Henein H, Wolfe T, Qureshi AJ. Sensor-fusion enabled inter-layer temperature control of nano-treated 7075 aluminum alloy produced through a wire-arc directed energy deposition process. Prog Addit Manuf. 2024. https://doi.org/10.1007/s40964-024-00707-9.10.1007/s40964-024-00707-9 ↗
15. Cai X, Yang M, Qiao Y, Wang Z, Zhou J, Xue F. Experimental investigation on wear resistance and corrosion behavior of nickel-aluminum bronze alloy fabricated by wire-arc additive manufacturing. J Mater Res Technol. 2023;26:5801–15.10.1016/j.jmrt.2023.08.313 ↗
16. Luo W, Yuan X, Zhang Z, Cheng C, Liu H, Qiu H, Cheng X. Effect of volumetric energy density on the mechanical properties and corrosion resistance of laser-additive-manufactured AlCoCrFeNi2. 1 high-entropy alloys. J Alloys Compd. 2025;1010:178032.10.1016/j.jallcom.2024.178032 ↗
17. Deng R, Wei R, Zhang Y, Zhao C, Liang J, Bai Q, Li H, Ouyang C, He Q, Liu S, Kang X. Investigation of variable-temperature wear characteristics of austenitic stainless steel coatings fabricated via laser energy deposition. Wear. 2025;572: 205993.10.1016/j.wear.2025.205993 ↗
18. Qu X, Li X, Zhang L, Yi D, Wang J, Wen C, Zhao Z, Gu X, Lin Y, Liu B, Cao Y. Effect of construction angles on the microstructure and mechanical properties of LPBF-fabricated 15–5 PH stainless steel. Mater Sci Eng A. 2024;900:146423.10.1016/j.msea.2024.146423 ↗
19. Geng Z, Chen C, Song M, Luo J, Chen J, Li R, Zhou K. High strength Al0. 7CoCrFeNi2. 4 hypereutectic high entropy alloy fabricated by laser powder bed fusion via triple-nanoprecipitation. J Mater Sci Technol. 2024;187:141–55.10.1016/j.jmst.2023.11.054 ↗
20. Casalino G, Karamimoghadam M, Contuzzi N. Metal wire additive manufacturing: a comparison between arc laser and laser/arc heat sources. Inventions. 2023;8(2):52.10.3390/inventions8020052 ↗
21. Bellamkonda PN, Dwivedy M, Addanki R. Cold metal transfer technology-a review of recent research developments. Results Eng. 2024. https://doi.org/10.1016/j.rineng.2024.102423.10.1016/j.rineng.2024.102423 ↗
22. Rosli NA, Alkahari MR, bin Abdollah MF, Maidin S, Ramli FR, Herawan SG. Effects of wire feeding angle in wire arc additive manufacturing. J Mech Eng Res Dev. 2021;44:76100.
23. Rosli NA, Alkahari MR, Ramli FR, Sudin MN, Maidin S. Influence of process parameters in wire and arc additive manufacturing (WAAM) process. J Mech Eng (JMechE). 2021;17(2):69–78.10.24191/jmeche.v17i2.15301 ↗
24. Ou W, Mukherjee T, Knapp GL, Wei Y, DebRoy T. Fusion zone geometries, cooling rates and solidification parameters during wire arc additive manufacturing. Int J Heat Mass Transfer. 2018;127:1084–94.10.1016/j.ijheatmasstransfer.2018.08.111 ↗
25. Wu Q, Lu J, Liu C, Shi X, Ma Q, Tang S, Fan H, Ma S. Obtaining uniform deposition with variable wire feeding direction during wire-feed additive manufacturing. Mater Manuf Process. 2017;32(16):1881–6.10.1080/10426914.2017.1364860 ↗
26. Han Q, Gao J, Han C, Zhang G, Li Y. Experimental investigation on improving the deposition rate of gas metal arc-based additive manufacturing by auxiliary wire feeding method. Weld World. 2021;65:35–45.10.1007/s40194-020-00994-0 ↗
27. Wang C, Suder W, Ding J, Williams S. The effect of wire size on high deposition rate wire and plasma arc additive manufacture of Ti-6Al-4V. J Mater Process Technol. 2021;288:116842.10.1016/j.jmatprotec.2020.116842 ↗
28. Dinovitzer M, Chen X, Laliberte J, Huang X, Frei H. Effect of wire and arc additive manufacturing (WAAM) process parameters on bead geometry and microstructure. Addit Manuf. 2019;26:138–46.
29. Gomez Ortega A, Corona Galvan L, Deschaux-Beaume F, Mezrag B, Rouquette S. Effect of process parameters on the quality of aluminium alloy Al5Si deposits in wire and arc additive manufacturing using a cold metal transfer process. Sci Technol Weld Join. 2018;23(4):316–32.10.1080/13621718.2017.1388995 ↗
30. Hejripour F, Valentine DT, Aidun DK. Study of mass transport in cold wire deposition for wire arc additive manufacturing. Int J Heat Mass Transf. 2018;125:471–84.10.1016/j.ijheatmasstransfer.2018.04.092 ↗
31. Ma Y, Cuiuri D, Hoye N, Li H, Pan Z. Effects of wire feed conditions on in situ alloying and additive layer manufacturing of titanium aluminides using gas tungsten arc welding. J Mater Res. 2014;29(17):2066–71.10.1557/jmr.2014.203 ↗
32. Chen X, Wang C, Ding J, Bridgeman P, Williams S. A three-dimensional wire-feeding model for heat and metal transfer, fluid flow, and bead shape in wire plasma arc additive manufacturing. J Manuf Process. 2022;83:300–12.10.1016/j.jmapro.2022.09.012 ↗
33. Meng Y, Li J, Zhang S, Gao M, Gong M, Chen H. Wire arc additive manufacturing of Ni-Al intermetallic compounds through synchronous wire-powder feeding. J Alloys Compd. 2023;943:169152.10.1016/j.jallcom.2023.169152 ↗
34. Wang L, Xue J, Wang Q. Correlation between arc mode, microstructure, and mechanical properties during wire arc additive manufacturing of 316L stainless steel. Mater Sci Eng A. 2019;751:183–90.10.1016/j.msea.2019.02.078 ↗
35. Hm V, Rao RN, Maiya M, Kumar P, Gupta N, Saxena KK, Vijayan V. Effects of arc current and travel speed on the processing of stainless steel via wire arc additive manufacturing (WAAM) process. J Adhes Sci Technol. 2024;38(12):2222–39.10.1080/01694243.2023.2289770 ↗
36. Souto JIVD, Lima JSD, Castro WBD, Santana RACD, Silva AA, Abreu Santos TFD, Tavares JMR. Effects of contaminations on electric arc behavior and occurrence of defects in wire arc additive manufacturing of 316L-Si stainless steel. Metals. 2024;14(3):286.10.3390/met14030286 ↗
37. Jing C, Mao H, Xu T, Guo Y, Lu J, Liang X, Liu C. Impact of process parameters on forming quality and deposition efficiency of unsupported rods in wire arc additive manufacturing. J Manuf Process. 2024;124:12–23.10.1016/j.jmapro.2024.06.001 ↗
38. Feng Y, Zhan B, He J, Wang K. The double-wire feed and plasma arc additive manufacturing process for deposition in Cr-Ni stainless steel. J Mater Process Technol. 2018;259:206–15.10.1016/j.jmatprotec.2018.04.040 ↗
39. Vander Voort GF, Lampman SR, Sanders BR, Anton GJ, Polakowski C, Kinson J, Muldoon K, Henry SD, Scott WW Jr. ASM handbook Metallography and microstructures. 2004;9:44073–50002.
40. Chen M, Zhang D, Wu C. Current waveform effects on CMT welding of mild steel. J Mater Process Technol. 2017;243:395–404.10.1016/j.jmatprotec.2017.01.004 ↗
41. Moradi M, KaramiMoghadam M. High power diode laser surface hardening of AISI 4130; statistical modelling and optimization. Opt Laser Technol. 2019;111:554–70.10.1016/j.optlastec.2018.10.043 ↗
42. Xia C, Pan Z, Polden J, Li H, Xu Y, Chen S. Modelling and prediction of surface roughness in wire arc additive manufacturing using machine learning. J Intell Manuf. 2022;33(5):1467–82.10.1007/s10845-020-01725-4 ↗
43. Bilmes P, Gonzalez A, Llorente C, Solari M. Effect of δ ferrite solidification morphology of austenitic stainless steel weld metal on properties of welded joints. Weld Int. 1996;10(10):797–808.10.1080/09507119609549091 ↗
44. Treutler K, Wesling V. The current state of research of wire arc additive manufacturing (WAAM): a review. Appl Sci. 2021;11(18):8619.10.3390/app11188619 ↗
45. Liu J, Xu J, Paik KW, He P, Zhang S. In-situ isothermal aging TEM analysis of a micro Cu/ENIG/Sn solder joint for flexible interconnects. J Mater Sci Technol. 2024;169:42–52.10.1016/j.jmst.2023.06.020 ↗
46. Ji R, Zhao Q, Zhao L, Liu Y, Jin H, Wang L, Wu L, Xu Z. Study on high wear resistance surface texture of electrical discharge machining based on a new water-in-oil working fluid. Tribol Int. 2023;180:108218.10.1016/j.triboint.2023.108218 ↗
47. Morvayova, A., Karamimoghadam, M., Contuzzi, N., Denora, V., Fabbiano, L. and Casalino, G., 2025. Experimental and numerical study of the effects of deposition speed and arc power on a single AISI 308L WAAM bead. Progress in Additive Manufacturing, pp.1–19.10.1007/s40964-025-01108-2 ↗
48. Guo X, Tian D, Li C, Li X, Li W, Cao M, Zhang F, Wang B. Optimization for the process parameters of Nickel-Titanium nitride composites fabricated via jet pulse electrodeposition. Nanomaterials. 2024;14(24):2034.10.3390/nano14242034 ↗
49. Long X, Su T, Lu C, Wang S, Huang J, Chang C. An insight into dynamic properties of SAC305 lead-free solder under high strain rates and high temperatures. Int J Impact Eng. 2023;175:104542.10.1016/j.ijimpeng.2023.104542 ↗
50. Obilanade D, Dordlofva C, Törlind P. Surface roughness considerations in design for additive manufacturing-a literature review. Proc Des Soc. 2021;1:2841–50.10.1017/pds.2021.545 ↗
51. Nandhakumar R, Venkatesan K. A process parameters review on selective laser melting-based additive manufacturing of single and multi-material: microstructure, physical properties, tribological, and surface roughness. Mater Today Commun. 2023;35:105538.10.1016/j.mtcomm.2023.105538 ↗
52. Di Schino A, Barteri M, Kenny JM. Effects of grain size on the properties of a low nickel austenitic stainless steel. J Mater Sci. 2003;38:4725–33.10.1023/A:1027470917858 ↗
53. Di Schino A, Barteri M, Kenny JM. Grain size dependence of mechanical, corrosion and tribological properties of high nitrogen stainless steels. J Mater Sci. 2003;38:3257–62.10.1023/A:1025181820252 ↗