journal article·2025-01-28Open access

Mechanical anchorage system in retrofitting of RC slabs using CFRP rods and concrete jacket

Firas Hassan Saeed, Farzad Hejazi, Raizal Saifulnaz Muhammad Rashid

Abstract

Abstract Over the past few decades, the demand for retrofitting reinforced concrete members has risen dramatically. Retrofitting reinforced concrete slabs with carbon-fiber-reinforced polymer (CFRP) rods and ultra-high-performance-fiber-reinforced-concrete (UHPFRC) jackets is the one of significantly effective techniques. However, the main challenge of employing CFRP rods and UHPFRC jackets technique to strengthen existing reinforced concrete members is the efficiency of using CFRP rods and the debonding issue between old and fresh new concrete jacketing. Debonding mostly occurs between CFRP rods and old concrete, as well as the surfaces of old and new concrete, and is especially prevalent when the slab is subjected to daily repetitive loads such as cyclic loads. In this study, a new retrofitting system utilizing a mechanical anchor system was proposed to improve the bond between the UHPFRC layer and existing slab. This mechanical system incorporates an expandable anchorage bolt and steel plates. Therefore, a benchmark RC slab and two retrofitted RC slabs were experimentally tested under a five-point incremental repeated load (cyclic load) employing the dynamic actuator. The influence of embedded CFRP rods into the jacket of UHPFRC on the performance of system were studied. The experimental results showed that the newly proposed approach was significantly effective in preventing early debonding. In addition, the mechanical system played an essential role by improving the attachment between the jacket and the slab, ensuring better load transfer. A new proposed retrofitting technique improved the capacity of slabs from 164 to 298kN, illustrating an improvement of over 82%. On the other hand, the FE models have been developed to provide both practical validation and deeper analytical insights, ensuring a comprehensive evaluation of the proposed retrofitting system. Experimental data were used to validate the results of the finite-element models, which showed good agreement and high accuracy. Finally, a parametric study was executed to evaluate the impact of various parameters on the performance and efficacy of the new suggested strengthening technique, and to optimize the proposed system parameters, including the diameter of bolts, a normal strength concrete (NSC) jacket with various grades rather than the UHPFRC, applying the proposed retrofitting technique on a compressive side instead of a tension zone, and rebar steel of varying diameters in the jacket instead of CFRP rods. Findings indicated (parametric study) that using anchor bolts with a diameter greater than 12 mm improved the slabs’ ultimate load capacity.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Structural Behavior of Reinforced Concrete · Innovative concrete reinforcement materials · Structural Load-Bearing Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (44)

Show source-provided references
1. Le Hoang A, Fehling E. Influence of steel fiber content and aspect ratio on the uniaxial tensile and compressive behavior of ultra high performance concrete. Constr Build Mater. 2017;153:790–806. https://doi.org/10.1016/j.conbuildmat.2017.07.130.10.1016/j.conbuildmat.2017.07.130 ↗
2. Tayeh BA, Bakar BA, Johari MM, Voo YL. Mechanical and permeability properties of the interface between normal concrete substrate and ultra high performance fiber concrete overlay. Constr build mater. 2012;36:538–48. https://doi.org/10.1016/j.conbuildmat.2012.06.013.10.1016/j.conbuildmat.2012.06.013 ↗
3. Brühwiler E, Denarié E. Rehabilitation and strengthening of concrete structures using ultra-high performance fibre reinforced concrete. Struct Eng Int. 2013;23(4):450–7. https://doi.org/10.2749/101686613X13627347100437.10.2749/101686613X13627347100437 ↗
4. Wu Z, Shi C, Khayat KH. Investigation of mechanical properties and shrinkage of ultra-high performance concrete: Influence of steel fiber content and shape. Compos Part B: Eng. 2019;174:107021. https://doi.org/10.1016/j.compositesb.2019.107021.10.1016/j.compositesb.2019.107021 ↗
5. Noshiravani T, Brühwiler E. Rotation capacity and stress redistribution ability of R-UHPFRC-RC composite continuous beams: an experimental investigation. Mater Struct Constr. 2013;46(12):2013–28. https://doi.org/10.1617/s11527-013-0033-5.10.1617/s11527-013-0033-5 ↗
6. Habel K, Gauvreau P. Response of ultra-high performance fiber reinforced concrete (UHPFRC) to impact and static loading. Cem Concr Compos. 2008;30(10):938–46. https://doi.org/10.1016/j.cemconcomp.2008.09.001.10.1016/j.cemconcomp.2008.09.001 ↗
7. Chun B, Yoo DY. Hybrid effect of macro and micro steel fibers on the pullout and tensile behaviors of ultra-high-performance concrete. Compos Part B: Eng. 2019;162:344–60. https://doi.org/10.1016/j.compositesb.2018.11.026.10.1016/j.compositesb.2018.11.026 ↗
8. Murthy AR, Karihaloo BL, Rani PV, Priya DS. Fatigue behaviour of damaged RC beams strengthened with ultra high performance fibre reinforced concrete. Int J Fatigue. 2018;116:659–68. https://doi.org/10.1016/j.ijfatigue.2018.06.046.10.1016/j.ijfatigue.2018.06.046 ↗
9. El-Mandouh MA, Elsamak G, Rageh BO, Hamoda A, Abdelazeem F. Experimental and numerical investigation of one-way reinforced concrete slabs using various strengthening systems. Case Stud Constr Mater. 2023;18:e01691. https://doi.org/10.1016/j.cscm.2022.e01691.10.1016/j.cscm.2022.e01691 ↗
10. Nadir W, Kadhimi MMA, Jawdhari A, Fam A, Majdi A. RC beams strengthened in shear with FRP-Reinforced UHPC overlay: an experimental and numerical study. Structures. 2023;53(April):693–715. https://doi.org/10.1016/j.istruc.2023.04.117.10.1016/j.istruc.2023.04.117 ↗
11. Wang H, Zhou Z, Zhang Z, Zou Y, Jiang J, Zeng X. Experimental and numerical studies on shear behavior of prefabricated bridge deck slabs with compact UHPC wet joint. Case Stud Const Mat. 2023;19:e02362. https://doi.org/10.1016/j.cscm.2023.e02362.10.1016/j.cscm.2023.e02362 ↗
12. Su YL, Wu C, Shang JQ, Zhang P, Sheikh SA. Experimental and numerical simulation research on the flexural performance of beams reinforced with GFRP bars and three-sides UHPC layer. Structures. 2024;59:105746. https://doi.org/10.1016/j.istruc.2023.105746.10.1016/j.istruc.2023.105746 ↗
13. Shan Y, et al. Flexural behavior of ultra-high performance concrete (UHPC) shaped thin-plate ribbed staircases: an experimental and numerical study. Mater Struct Constr. 2024;57(1):1–17. https://doi.org/10.1617/s11527-023-02282-x.10.1617/s11527-023-02282-x ↗
14. Safdar M, Matsumoto T, Kakuma K. Flexural behavior of reinforced concrete beams repaired with ultra-high performance fiber reinforced concrete (UHPFRC). Compos Struct. 2016;157:448–60. https://doi.org/10.1016/j.compstruct.2016.09.010.10.1016/j.compstruct.2016.09.010 ↗
15. Paschalis SA, Lampropoulos AP, Tsioulou O. Experimental and numerical study of the performance of ultra high performance fiber reinforced concrete for the flexural strengthening of full scale reinforced concrete members. Constr Build Mater. 2018;186:351–66. https://doi.org/10.1016/j.conbuildmat.2018.07.123.10.1016/j.conbuildmat.2018.07.123 ↗
16. Ramachandra Murthy A, Karihaloo BL, Priya DS. Flexural behavior of RC beams retrofitted with ultra-high strength concrete. Constr Build Mater. 2018;175:815–24. https://doi.org/10.1016/j.conbuildmat.2018.04.174.10.1016/j.conbuildmat.2018.04.174 ↗
17. Ahmed S, Mohamed EY, Mohamed HA, Emara M. Experimental and numerical investigation of flexural behavior of RC beams retrofitted with reinforced UHPFRC layer in tension surface. Structures. 2023;49:106–23. https://doi.org/10.1016/j.istruc.2023.01.113.10.1016/j.istruc.2023.01.113 ↗
18. Al-Osta MA, Isa MN, Baluch MH, Rahman MK. Flexural behavior of reinforced concrete beams strengthened with ultra-high performance fiber reinforced concrete. Constr Build Mater. 2017;134:279–96. https://doi.org/10.1016/j.conbuildmat.2016.12.094.10.1016/j.conbuildmat.2016.12.094 ↗
19. Li C, Aoude H. Influence of UHPFRC jacketing on the static, blast and post-blast behaviour of doubly-reinforced concrete beams. Int J Impact Eng. 2023;179:104656. https://doi.org/10.1016/j.ijimpeng.2023.104656.10.1016/j.ijimpeng.2023.104656 ↗
20. Yang J, Yu J, Zhang Z, Zou Y, Chen R, Zhou J, Li B. Flexural behavior of 15-year-old full-scale hollow slab beams strengthened with fiber-reinforced composites. Case Stud Constr Mater. 2023;19:e02545. https://doi.org/10.1016/j.cscm.2023.e02545.10.1016/j.cscm.2023.e02545 ↗
21. Sun W, Fan W, Yang J, Wu Q, Zhong Z. Numerical simulation and design method of the interface of UHPFRC-strengthened RC structures using post-installed rebars. Eng Struct. 2023;15(289):116286. https://doi.org/10.1016/j.engstruct.2023.116286.10.1016/j.engstruct.2023.116286 ↗
22. Saeed FH, Hejazi F, Rashid RS. Strengthening of reinforced concrete slabs using carbon fiber reinforced polymers rods and concrete jacket with a mechanical anchorage system. Constr Build Mater. 2024;440:137464. https://doi.org/10.1016/j.conbuildmat.2024.137464.10.1016/j.conbuildmat.2024.137464 ↗
23. Hong SG, Lim WY. Strengthening of shear-dominant reinforced concrete beams with ultra-high-performance concrete jacketing. Constr Build Mater. 2023;365:130043. https://doi.org/10.1016/j.conbuildmat.2022.130043.10.1016/j.conbuildmat.2022.130043 ↗
24. Paschalis SA, Lampropoulos AP. Developments in the use of ultra high performance fiber reinforced concrete as strengthening material. Eng Struct. 2021;233:111914. https://doi.org/10.1016/j.engstruct.2021.111914.10.1016/j.engstruct.2021.111914 ↗
25. Said A, Elsayed M, Abd El-Azim A, Althoey F, Tayeh BA. Using ultra-high performance fiber reinforced concrete in improvement shear strength of reinforced concrete beams. Case Stud Constr Mater. 2022;16:e01009. https://doi.org/10.1016/j.cscm.2022.e01009.10.1016/j.cscm.2022.e01009 ↗
26. Mostofinejad D, Moghaddas A. Bond efficiency of EBR and EBROG methods in different flexural failure mechanisms of FRP strengthened RC beams. Constr Build Mater. 2014;54:605–14. https://doi.org/10.1016/j.conbuildmat.2014.01.002.10.1016/j.conbuildmat.2014.01.002 ↗
27. Coelho MRF, Sena-Cruz JM, Neves LAC. A review on the bond behavior of FRP NSM systems in concrete. Constr Build Mater. 2015;93:1157–69. https://doi.org/10.1016/j.conbuildmat.2015.05.010.10.1016/j.conbuildmat.2015.05.010 ↗
28. T. Datasheet, “Hilti Hst3 Expansion Anchor.”
29. I. Units, 318–19 Building Code Requirements for Structural Concrete and Commentary. 2019.
30. Pedram Z, Xiong Y, Xin J, Amir M. Punching shear enhancement of flat slabs with partial use of ultrahigh-performance concrete. J Mater Civ Eng. 2015;27(9):4014255. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001219.10.1061/(ASCE)MT.1943-5533.0001219 ↗
31. Bars S, et al. Standard specification for general requirements for steel bars, carbon and alloy, hot-wrought 1 title of specification ASTM designation A. Constr Build Mater. 2013;1:1–16. https://doi.org/10.1520/A0029.10.1520/A0029 ↗
32. Zhang Y, Wang H, Qin Y, Huang S, Fan W. Experimental and analytical studies on the flexural behavior of steel plate-UHPC composite strengthened RC beams. Eng Struct. 2023;283:115834. https://doi.org/10.1016/j.engstruct.2023.115834.10.1016/j.engstruct.2023.115834 ↗
33. A. C. I. C. 239, ACI 239R-18 Ultra-High-Performance Concrete: An Emerging Technology Report. American Concrete Institute, 2018.
34. P. D. Sheet, “Sika ® CarboDur ® BC 8,” no. October, pp. 8–10, 2023.
35. Pan B, Liu F, Zhuge Y, Zeng JJ, Liao J. ECCs/UHPFRCCs with and without FRP reinforcement for structural strengthening/repairing: a state-of-the-art review. Constr Build Mater. 2022;316:125824. https://doi.org/10.1016/j.conbuildmat.2021.125824.10.1016/j.conbuildmat.2021.125824 ↗
36. C. A. E. User, “Abaqus theory manual,” Abaqus 6.13 Doc., no. Dassault Systemes Simulia Corp., Providence, RI, USA., 2014.
37. GB, “National Standard of the People’s Republic of China - Code for Design of Concrete Structures,” Construction, vol. Beijing, pp. 64–73, 2002.
38. Jia L, Fang Z, Huang Z, Pilakoutas K, Wang Q, Tan X. Flexural behavior of uhpc beams prestressed with external cfrp tendons. Appl Sci. 2021;11(19):9189. https://doi.org/10.3390/app11199189.10.3390/app11199189 ↗
39. Asadi M. Experimental Test and Finite Element Modelling of Pedestrian. Test, No. Figure. 2010;1:60876.
40. dos Santos LR, de Sousa CH, Caldas RB, Grilo LF. Finite element model for bolted shear connectors in concrete-filled steel tubular columns. Eng Struct. 2020;203:109863. https://doi.org/10.1016/j.engstruct.2019.109863.10.1016/j.engstruct.2019.109863 ↗
41. Obaidat YT, Heyden S, Dahlblom O. The effect of CFRP and CFRP/concrete interface models when modelling retrofitted RC beams with FEM. Compos Struct. 2010;92(6):1391–8. https://doi.org/10.1016/j.compstruct.2009.11.008.10.1016/j.compstruct.2009.11.008 ↗
42. Ayough P, Sulong NR, Ibrahim Z. Analysis and review of concrete-filled double skin steel tubes under compression. Thin-Walled Struct. 2020;148:106495. https://doi.org/10.1016/j.tws.2019.106495.10.1016/j.tws.2019.106495 ↗
43. Belakhdar K, Tounsi A. Finite element analysis of initially damaged beams repaired with FRP plates. Compos Struct. 2015;134:429–39. https://doi.org/10.1016/j.compstruct.2015.07.124.10.1016/j.compstruct.2015.07.124 ↗
44. Hawileh RA, Rasheed HA, Abdalla JA, Al-Tamimi AK. Behavior of reinforced concrete beams strengthened with externally bonded hybrid fiber reinforced polymer systems. Mater Des. 2014;53:972–82. https://doi.org/10.1016/j.matdes.2013.07.087.10.1016/j.matdes.2013.07.087 ↗