Investigation of alite hydration in the presence of low- and high-silica zeolites
Source abstract
Abstract
Abstract Synthetic zeolites that are obtained from the hydrothermal reaction of NaOH with fly ash have a well-defined pore structure and pozzolanic properties. This work examines the effect of the low-silica (Na-A) and high-silica (ZSM-5) zeolite structure on the kinetics of alite hydration and mineralogical characteristics of the reaction products. The addition of the Na-A and ZSM-5 zeolites reduced the rate of heat release during the hydration reaction, which is typical for commonly used pozzolanic additives. The ZSM-5 zeolite had a much higher Si/Al ratio relative to the Na-A zeolite, which translated into a higher pozzolanic activity and resulted in greater stability of the hydration reaction kinetics. The addition of zeolites caused the heat of hydration to decrease compared to the reference pastes (the alite reference paste—206 J/g): Na-A 15%—148.9 J/g; ZSM-5 15%—149.9 J/g. The concentration of calcium ions in the alite solution and the content of active silica were identified as the most important parameters affecting the kinetic, morphological, and structural characteristics of the C–S–H phase. The addition of zeolites increased the amount of C–S–H gel phases formed. At the same time, the proportion of portlandite in the hydration products of the alite–zeolite systems decreased. Pozzolans reduced the ratio of CaO/SiO2 in the C–S–H phase, which for pastes with the addition of the Na-A ranged from 1.61 to 1.37, and for the ZSM-5 from 1.91 to 0.47. This ratio decreased with the dosage and the age of alite paste. In summary, this research has shown that synthetic zeolites are a viable pozzolanic additives.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Concrete and Cement Materials Research · Clay minerals and soil interactions · Recycling and utilization of industrial and municipal waste in materials production
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (41)
Show source-provided references
1. N Mahasenan, S Smith, K Humphreys (2003) The Cement Industry and Global Climate Change: Current and Potential Future Cement Industry CO2 Emissions, in: J. Gale, Y.B.T.-G.G.C.T. 6th I.C. Kaya (Eds.), Pergamon, Oxford, 995–1000. https://doi.org/10.1016/B978-008044276-1/50157-410.1016/B978-008044276-1/50157-4 ↗
2. Moghaddam F, Sirivivatnanon V, Vessalas K. The effect of fly ash fineness on heat of hydration, microstructure, flow and compressive strength of blended cement pastes. Case Stud Construc Mater. 2019;10:00218. https://doi.org/10.1016/j.cscm.2019.e00218.10.1016/j.cscm.2019.e00218 ↗
3. Sánchez Berriel S, Favier A, Rosa Domínguez E, Sánchez Machado IR, Heierli U, Scrivener K, Martirena Hernández F, Habert G. Assessing the environmental and economic potential of limestone calcined clay cement in Cuba. Cleaner Product. 2016;124:361–9. https://doi.org/10.1016/j.jclepro.2016.02.125.10.1016/j.jclepro.2016.02.125 ↗
4. Vigil de la Villa R, Fernández R, García R, Villar-Cociña E, Frías M. Pozzolanic activity and alkaline reactivity of a mordenite-rich tuff. Microp Mesop Mater. 2009;126:125–32. https://doi.org/10.1016/j.micromeso.2009.05.029.10.1016/j.micromeso.2009.05.029 ↗
5. Taylor HFW. The chemistry of cements. New York: Academic Press; 1964.
6. Famy C, Scrivener KL, Crumbie AK. What causes differences of C-S–H gel grey levels in backscattered electron images. Cement Concrete Res. 2002;32:1465–71. https://doi.org/10.1016/S0008-8846(02)00808-6.10.1016/S0008-8846(02)00808-6 ↗
7. Özen S, Göncüoʇlu MC, Liguori B, De Gennaro B, Cappelletti P, Gatta GD, Iucolano F, Colella C. A comprehensive evaluation of sedimentary zeolites from Turkey as pozzolanic addition of cement- and lime-based binders. Constr Build Mater. 2016;105:46–61. https://doi.org/10.1016/j.conbuildmat.2015.12.055.10.1016/j.conbuildmat.2015.12.055 ↗
8. Markiv T, Sobol K, Franus M, Franus W. Mechanical and durability properties of concretes incorporating natural zeolite. Arch Civil Mech Eng. 2016;16:554–62. https://doi.org/10.1016/j.acme.2016.03.013.10.1016/j.acme.2016.03.013 ↗
9. Moghaddam F, Sirivivatnanon V, Vessalas K. The effect of fly ash fineness on heat of hydration, microstructure, flow and compressive strength of blended cement pastes. Case Stud Constr Mater. 2019;10:e00218. https://doi.org/10.1016/j.cscm.2019.e00218.10.1016/j.cscm.2019.e00218 ↗
10. Mertens G, Snellings R, Van Balen K, Bicer-Simsir B, Verlooy P, Elsen J. Pozzolanic reactions of common natural zeolites with lime and parameters affecting their reactivity. Cem Concr Res. 2009;39:233–40. https://doi.org/10.1016/j.cemconres.2008.11.008.10.1016/j.cemconres.2008.11.008 ↗
11. Sobol K, Markiv T, Terlyha V, Franus W. Peculiarities of hydration processes of cements containing natural zeolite. Budown Arch. 2015;14:105–13.10.35784/bud-arch.1674 ↗
12. Wdowin M, Franus W, Panek R. Preliminary results of usage possibilities of carbonate and zeolitic sorbents in CO2 capture, Fresenius Environ. Bull. 2012;21:3726–34.
13. Chałupnik S, Franus W, Wysocka M, Gzyl G. Application of zeolites for radium removal from mine water. Environ Sci Pollut Res. 2013;20:7900–6. https://doi.org/10.1007/s11356-013-1877-5.10.1007/s11356-013-1877-5 ↗
14. Janotka I. Hydration of portland cement, natural zeolite mortar in water and sulphate solution. Grasas Aceites. 2001. https://doi.org/10.3989/egeogr.2001.i245.267.10.3989/egeogr.2001.i245.267 ↗
15. Franus W, Wdowin M, Franus M. Synthesis and characterization of zeolites prepared from industrial fly ash. Environ Monit Assess. 2014;186:5721–9. https://doi.org/10.1007/s10661-014-3815-5.10.1007/s10661-014-3815-5 ↗
16. Snellings R, Mertens G, Cizer Ö, Elsen J. Early age hydration and pozzolanic reaction in natural zeolite blended cements: Reaction kinetics and products by in situ synchrotron X-ray powder. Cem Concr Res. 2010. https://doi.org/10.1016/j.cemconres.2010.08.012.10.1016/j.cemconres.2010.08.012 ↗
17. Nicoleau L, Nonat A, Perrey D. The di- and tricalcium silicate dissolutions. Cement Concrete Res. 2013;47:14–30. https://doi.org/10.1016/j.cemconres.2013.01.017.10.1016/j.cemconres.2013.01.017 ↗
18. Bergold ST, Goetz-Neunhoeffer F, Neubauer J. Mechanically activated alite: New insights into alite hydration. Cem Concr Res. 2015;76:202–11. https://doi.org/10.1016/j.cemconres.2015.06.005.10.1016/j.cemconres.2015.06.005 ↗
19. Jennings HM. Aqueous solubility relationships for two types of calcium silicate hydrate. J Am Ceram Soc. 1986;69:614–8. https://doi.org/10.1111/j.1151-2916.1986.tb04818.x.10.1111/j.1151-2916.1986.tb04818.x ↗
20. F. Bellmann, T. Sowoidnich, B. Möser, Formation of an intermediate phase and influence of crystallographic defects on dissolution of C3S, Proceedings of the XIII. International Congress on the Chemistry of Cement, 3–8 (2011), Madrid (Spain)
21. Bellmann F, Damidot D, Möser B, Skibsted J. Improved evidence for the existence of an intermediate phase during hydration of tricalcium silicate. Cement Concrete Res. 2010;40:875–84. https://doi.org/10.1016/j.cemconres.2010.02.007.10.1016/j.cemconres.2010.02.007 ↗
22. Roszczynialski W, Stępień P, Tkaczewska E. Ocena metod badania aktywności pucolanowej popiołów lotnych/ The reliability of pozzolanic activity assessment methods in testing different fly ashes (Polish article). Cement Wapno Beton. 2014;18:323–33.
23. Yin B, Kang T, Kang J, Chen Y, Wu L, Du M. Investigation of the hydration kinetics and microstructure formation mechanism of fresh fly ash cemented filling materials based on hydration heat and volume resistivity characteristics. Appl Clay Sci. 2018;166:146–58. https://doi.org/10.1016/j.clay.2018.09.019.10.1016/j.clay.2018.09.019 ↗
24. Wang L, Guo F, Lin Y, Yang H, Tang SW. Comparison between the effects of phosphorous slag and fly ash on the C-S–H structure, long-term hydration heat and volume deformation of cement-based materials. Construct Build Mater. 2020;250:118807. https://doi.org/10.1016/j.conbuildmat.2020.118807.10.1016/j.conbuildmat.2020.118807 ↗
25. Ramanathan S, Pestana LR, Suraneni P. Thermo-mechanical stability of supplementary cementitious materials in cement paste to be incorporated in concrete as thermal energy storage material at high temperatures. Cement. 2022;8:100022. https://doi.org/10.1016/j.cement.2022.100022.10.1016/j.cement.2022.100022 ↗
26. Cyr M, Lawrence P, Ringot E. Efficiency of mineral admixtures in mortars: Quantification of the physical and chemical effects of fine admixtures in relation with compressive strength. Cement Concrete Res. 2006;36:264–77. https://doi.org/10.1016/j.cemconres.2005.07.001.10.1016/j.cemconres.2005.07.001 ↗
27. Huang Y, Wang Q, Shi M. Characteristics and reactivity of ferro-nickel slag powder. Construct Build Mater. 2017;156:773–89. https://doi.org/10.1016/j.conbuildmat.2017.09.038.10.1016/j.conbuildmat.2017.09.038 ↗
28. Alhozaimy A, Fares G, Alawad OA, Al-Negheimish A. Heat of hydration of concrete containing powdered scoria rock as a natural pozzolanic material. Construct Build Mater. 2015;81:113–9. https://doi.org/10.1016/j.conbuildmat.2015.02.011.10.1016/j.conbuildmat.2015.02.011 ↗
29. Hu X, Shi C, Shi Z, Tong B, Wang D. Early age shrinkage and heat of hydration of cement-fly ash-slag ternary blends. Construct Build Mater. 2017;153:857–65. https://doi.org/10.1016/j.conbuildmat.2017.07.138.10.1016/j.conbuildmat.2017.07.138 ↗
30. Sun J, Shi H, Qian B, Xu Z, Li W, Shen X. Effects of synthetic C-S–H/PCE nanocomposites on early cement hydration. Construct Build Mater. 2017;140:282–92. https://doi.org/10.1016/j.conbuildmat.2017.02.075.10.1016/j.conbuildmat.2017.02.075 ↗
31. Perez JP, Nonat A, Pourchet S, Garrault M, Canevet C. Why TIPA leads to an increase in the mechanical properties of mortars whereas TEA does not. ACI Mater J. 2003;217:583–94.
32. W Nocuń-Wczelik (2004) Przyczynek do badań kinetyki i mechanizmu oddziaływania domieszek do betonu/A contribution to the study of the kinetics and mechanism of interaction of concrete admixtures (Polish publication), Dni Betonu, 335–347
33. Jadhav R, Debnath NC. Computation of X-ray powder diffractograms of cement components and its application to phase analysis and hydration performance of OPC cement. Bull Mater Sci. 2011;34:1137–50. https://doi.org/10.1007/s12034-011-0134-0.10.1007/s12034-011-0134-0 ↗
34. Zhang R, Cheng X, Hou P, Ye Z. Influences of nano-TiO2 on the properties of cement-based materials: hydration and drying shrinkage. Construct Build Mater. 2015;81:35–41. https://doi.org/10.1016/j.conbuildmat.2015.02.003.10.1016/j.conbuildmat.2015.02.003 ↗
35. F Sybertz, U Wiens (1991), Effect of fly ash fineness on hydration characteristics and strength development, Int Conf on Blended Cements in Construction, London: Großbritannien 152–16510.1201/9781482296631-12 ↗
36. W. Franus, R. Panek, M. Wdowin (2015) SEM Investigation of Microstructures in Hydration Products of Portland Cement, 2nd international multidisciplinary microscopy and microanalysis congress, springer international publishing 105–11210.1007/978-3-319-16919-4_14 ↗
37. S Diamond (1976) The composition of the gel phase in Portland cement paste, Cement and Concrete Association 334
38. Bi R, Cheng W, Chen X. Effect of calcium sulfate variety and content on hydration mechanism of grout sealants for coal-bed methane drainage boreholes. Construct Build Mater. 2019;203:443–55. https://doi.org/10.1016/j.conbuildmat.2019.01.046.10.1016/j.conbuildmat.2019.01.046 ↗
39. Liao K-Y, Chang P-K, Peng Y-N, Yang C-C. A study on characteristics of interfacial transition zone in concrete. Cement Concrete Res. 2004;34:977–89. https://doi.org/10.1016/j.cemconres.2003.11.019.10.1016/j.cemconres.2003.11.019 ↗
40. Gao P, Lu X, Yang C, Li X, Shi N, Jin S. Microstructure and pore structure of concrete mixed with superfine phosphorous slag and superplasticizer. Construct Build Mater. 2008;22:837–40. https://doi.org/10.1016/j.conbuildmat.2006.12.015.10.1016/j.conbuildmat.2006.12.015 ↗
41. Garrault S, Finot E, Lesniewska E, Nonat A. Study of C-S–H growth on C3S surface during its early hydration. Mater Struct. 2005;38:435–42. https://doi.org/10.1617/14343.10.1617/14343 ↗