journal article·2024-06-14Open access

Determination of the fracture toughness of carburized Pyrowear 53 steel for planetary gears by the small punch test method

Kamil Majchrowicz, Barbara Romelczyk-Baishya, Monika Wieczorek-Czarnocka, Anna Dobkowska, Krzysztof Raga, Ryszard Filip, Zbigniew Pakieła

Abstract

Abstract The aim of the current study was to determine the fracture toughness of different zones in carburized Pyrowear 53 steel using the small punch test (SPT) method. Firstly, Pyrowear 53 steel was quenched and tempered using different processing parameters to obtain core materials with varied microstructures and fracture toughness. The results obtained for the core material in standard fracture toughness tests were then compared with the SPT results, which allowed the determination of a formula correlating the fracture energy integral,JSPT, from the SPT withJQintegrals obtained from standardized compact tension specimens. In the next stage, Pyrowear 53 steel was carburized at 925 °C and divided into the following zones: (1) a carburized layer (up to 0.5 mm from the surface), (2) a transition layer (from 0.5 to 1.5 mm), and (3) a core zone (more than 1.5 mm). Each zone was characterized in terms of its microstructure and tensile properties using miniaturized test specimens. Finally, the fracture toughness values of the core zone (JSPT = 78–102 kJ/m2), the transition layer (JSPT = 71–80 kJ/m2), and the carburized layer (JSPT = 8.1–9.1 kJ/m2) were determined based on the obtained SPT results. It was shown that the use of such a relatively simple SPT method with the proposed energy-based approach seems to be a promising way of determining the fracture toughness of thin layers or local changes in the fracture behavior of surface-treated materials.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Fatigue and fracture mechanics · High Temperature Alloys and Creep

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (50)

Show source-provided references
1. Ferguson BL, Freborg AM, Li Z. Residual stress and bending fatigue strength in carburized and quench hardened Pyrowear 53 steel gears, Proc 23rd Int Fed Heat Treat Surf Eng Congr 2016. 2016;374–381.
2. Korecki M, Wolowiec-Korecka E, Bazel M, Slut M, Kreuzaler TD, Outstanding Hardening of Pyrowear® Alloy 53 With Low Pressure Carburizing, Tech. Contrib. to 70° Congr. Anu. Da ABM, Rio Janeiro, Brazil, 17–21 August. 2015;1311–1320.10.5151/1516-392X-26718 ↗
3. Wojtyczka A, Iżowski B. Microstructure and hardness of Pyrowear 53 steel after low-pressure vacuum carburizing at 921°C. Adv Manuf Sci Technol. 2020;44:109–12. https://doi.org/10.2478/amst-2019-0020.10.2478/amst-2019-0020 ↗
4. Peng T, Cao J-C, Zhao J-Q, Yang G. Cu precipitation strengthening in AMS 6308 steel, Cailiao Rechuli Xuebao / Trans. Mater Heat Treat. 2016;37:126–30.
5. Srivatsan TS, Manigandan K, Freborg AM, Quick T. Investigating and understanding the cyclic fatigue, deformation, and fracture behavior of a novel high strength alloy steel: Influence of orientation. Steel Res Int. 2013;84:218–28.10.1002/srin.201200132 ↗
6. Arunkumar S. Overview of small punch test. Met Mater Int. 2020;26:719–38.10.1007/s12540-019-00454-5 ↗
7. Romelczyk-Baishya B, Łęczycki K, Płocińska M, Kulczyk M, Molak R, Pakieła Z. The effect of microstructure anisotropy on low temperature fracture of ultrafine-grained iron. Arch Civ Mech Eng. 2018;18:1166–82. https://doi.org/10.1016/j.acme.2018.02.014.10.1016/j.acme.2018.02.014 ↗
8. Chen H, Jackson GA, Sun W. An overview of using small punch testing for mechanical characterization of MCrAlY bond coats. J Therm Spray Technol. 2017;26:1222–38.10.1007/s11666-017-0593-y ↗
9. Foulds J, Viswanathan R. Small punch testing for determining the material toughness of low alloy steel components in service. J Eng Mater Technol. 1994;116:457–64.10.1115/1.2904313 ↗
10. Gülçimen B, Durmuş A, Ülkü S, Hurst RC, Turba K, Hähner P. Mechanical characterisation of a P91 weldment by means of small punch fracture testing. Int J Press Vessel Pip. 2013;105–106:28–35. https://doi.org/10.1016/j.ijpvp.2013.02.005.10.1016/j.ijpvp.2013.02.005 ↗
11. Bruchhausen M, Holmström S, Simonovski I, Austin T, Lapetite JM, Ripplinger S, de Haan F. Recent developments in small punch testing: tensile properties and DBTT. Theor Appl Fract Mech. 2016;86:2–10. https://doi.org/10.1016/j.tafmec.2016.09.012.10.1016/j.tafmec.2016.09.012 ↗
12. Romelczyk-Baishya B, Lumelskyj D, Stępniewska M, Giżyński M, Pakieła Z. The mechanical properties at room and low temperature of P110 steel characterised by means of small punch test. Arch Metall Mater. 2019;64:159–65. https://doi.org/10.24425/amm.2019.126232.10.24425/amm.2019.126232 ↗
13. Dobeš F, Milička K. Comparison of conventional and small punch creep tests of mechanically alloyed Al-C-O alloys. Mater Charact. 2008;59:961–4. https://doi.org/10.1016/j.matchar.2007.08.006.10.1016/j.matchar.2007.08.006 ↗
14. Rouse JP, Cortellino F, Sun W, Hyde TH, Shingledecker J. Small punch creep testing: Review on modelling and data interpretation. Mater Sci Technol. 2013;29:1328–45.10.1179/1743284713Y.0000000278 ↗
15. Bruchhausen M, Holmström S, Lapetite JM, Ripplinger S. On the determination of the ductile to brittle transition temperature from small punch tests on Grade 91 ferritic-martensitic steel. Int J Press Vessel Pip. 2017;155:27–34. https://doi.org/10.1016/j.ijpvp.2017.06.008.10.1016/j.ijpvp.2017.06.008 ↗
16. Stępniewska M, Romelczyk-Baishya B, Brynk T, Giżyński M, Pakieła Z, Influence of low temperature on mechanical properties of carbon steel P110 estimated by means of small punch test, Lect. Notes Mech. Eng. 2019;151–163.10.1007/978-981-13-0411-8_15 ↗
17. Álvarez G, Zafra A, Belzunce FJ, Rodríguez C. Hydrogen embrittlement testing procedure for the analysis of structural steels with small punch tests using notched specimens. Eng Fract Mech. 2021;253:1–14.10.1016/j.engfracmech.2021.107906 ↗
18. de Maia Almeida LF, Martiniano GA, da Silva Alvarenga RF, Piza Paes MT, Ramos Neto FF, Bose Filho WW, Arencibia RV, Franco SD. The evaluation of hydrogen embrittlement threshold force using the Small punch test. Theor Appl Fract Mech. 2023;125:103673.10.1016/j.tafmec.2022.103673 ↗
19. Mao X, Shoji T, Takahashi H. Characterization of fracture behavior in small punch test by combined recrystallization-etch method and rigid plastic analysis. J Test Eval. 1987;15:30–7.10.1520/JTE11549J ↗
20. Budzakoska E, Carr DG, Stathers PA, Li H, Harrison RP, Hellier AK, Yeung WY. Predicting the J integral fracture toughness of Al 6061 using the small punch test. Fatigue Fract Eng Mater Struct. 2007;30:796–807.10.1111/j.1460-2695.2007.01153.x ↗
21. Ha JS, Fleury E. Small punch tests to estimate the mechanical properties of steels for steam power plant: II. fracture toughness. Int J Press Vessel Pip. 1998;75:707–13.10.1016/S0308-0161(98)00075-1 ↗
22. Wang ZX, Shi HJ, Lu J, Shi P, Ma XF. Small punch testing for assessing the fracture properties of the reactor vessel steel with different thicknesses. Nucl Eng Des. 2008;238:3186–93. https://doi.org/10.1016/j.nucengdes.2008.07.013.10.1016/j.nucengdes.2008.07.013 ↗
23. Martínez-Pañeda E, García TE, Rodríguez C. Fracture toughness characterization through notched small punch test specimens. Mater Sci Eng A. 2016;657:422–30. https://doi.org/10.1016/j.msea.2016.01.077.10.1016/j.msea.2016.01.077 ↗
24. Álvarez G, Rodríguez C, Belzunce FJ, García TE. Use of notched small punch test specimens for the determination of fracture properties in structural steels. Theor Appl Fract Mech. 2020;106:102442. https://doi.org/10.1016/j.tafmec.2019.102442.10.1016/j.tafmec.2019.102442 ↗
25. Turba K, Gülçimen B, Li YZ, Blagoeva D, Hähner P, Hurst RC. Introduction of a new notched specimen geometry to determine fracture properties by small punch testing. Eng Fract Mech. 2011;78:2826–33. https://doi.org/10.1016/j.engfracmech.2011.08.014.10.1016/j.engfracmech.2011.08.014 ↗
26. Hurst R, Li Y, Turba K. Determination of fracture toughness from the small punch test using circular notched specimens. Theor Appl Fract Mech. 2019;103:102238. https://doi.org/10.1016/j.tafmec.2019.102238.10.1016/j.tafmec.2019.102238 ↗
27. Martínez-Pañeda E, Cuesta II, Peñuelas I, Díaz A, Alegre JM. Damage modeling in small punch test specimens. Theor Appl Fract Mech. 2016;86:51–60. https://doi.org/10.1016/j.tafmec.2016.09.002.10.1016/j.tafmec.2016.09.002 ↗
28. Alegre JM, Lacalle R, Cuesta II, Álvarez JA. Different methodologies to obtain the fracture properties of metallic materials using pre-notched small punch test specimens. Theor Appl Fract Mech. 2016;86:11–8. https://doi.org/10.1016/j.tafmec.2016.09.006.10.1016/j.tafmec.2016.09.006 ↗
29. Filip R, Ochał K, Gancarczyk K, Nowak WJ, Kościelniak B, Wierzba B. Characteristics of impulse carburization LPC process. Materials (Basel). 2021;14:4269. https://doi.org/10.3390/ma14154269.10.3390/ma14154269 ↗
30. Molak RM, Kartal ME, Pakiela Z, Kurzydlowski KJ. The effect of specimen size and surface conditions on the local mechanical properties of 14MoV6 ferritic-pearlitic steel. Mater Sci Eng A. 2016;651:810–21. https://doi.org/10.1016/j.msea.2015.11.037.10.1016/j.msea.2015.11.037 ↗
31. Sitek R, Puchlerska S, Nejman I, Majchrowicz K, Pakieła Z, Żaba K, Mizera J. The impact of plastic deformation on the microstructure and tensile strength of haynes 282 nickel superalloy produced by DMLS and casting. Materials (Basel). 2022;15:7545. https://doi.org/10.3390/ma15217545.10.3390/ma15217545 ↗
32. ASTM E646 - Standard Test Method for Tensile Strain-Hardening Exponents (n-Values) of Metallic Sheet Materials, 2016.
33. Baek MS, Kim KS, Park TW, Ham J, Lee KA. Quantitative phase analysis of martensite-bainite steel using EBSD and its microstructure, tensile and high-cycle fatigue behaviors. Mater Sci Eng A. 2020;785:139375.10.1016/j.msea.2020.139375 ↗
34. Wang Y, Hua J, Kong M, Zeng Y, Liu J, Liu Z. Quantitative analysis of martensite and bainite microstructures using electron backscatter diffraction. Microsc Res Tech. 2016;79:814–9.10.1002/jemt.22703 ↗
35. Zisman AA, Petrov SN, Ptashnik AV. Quantitative verification of high-strength alloyed steel bainite-martensite structures by scanning electron microscopy methods. Metallurgist. 2015;58:1019–24.10.1007/s11015-015-0034-4 ↗
36. Prasad RP, Putatunda SK. Influence of microstructure on fracture toughness of austempered ductile iron, Metall. Mater Trans A Phys Metall Mater Sci. 1997;28:1457–70.10.1007/s11661-997-0208-1 ↗
37. Wu R, Li W, Zhou S, Zhong Y, Wang L, Jin X. Effect of retained austenite on the fracture toughness of quenching and partitioning (Q&P)-treated sheet steels, Metall. Mater Trans A Phys Metall Mater Sci. 2014;45:1892–902.10.1007/s11661-013-2113-0 ↗
38. Webster D. Optimization of strength and toughness in two high-strength stainless steels. Metall Trans. 1971;2:1857–62.10.1007/BF02913416 ↗
39. Hu J, Du LX, Sun GS, Xie H, Misra RDK. The determining role of reversed austenite in enhancing toughness of a novel ultra-low carbon medium manganese high strength steel. Scr Mater. 2015;104:87–90. https://doi.org/10.1016/j.scriptamat.2015.04.009.10.1016/j.scriptamat.2015.04.009 ↗
40. Tomita Y. Effect of microstructure on plane-strain fracture toughness of AISI 4340 steel. Metall Trans A. 1988. https://doi.org/10.1007/BF02645479.10.1007/BF02645479 ↗
41. Abdollah-Zadeh A, Salemi A, Assadi H. Mechanical behavior of CrMo steel with tempered martensite and ferrite-bainite-martensite microstructure. Mater Sci Eng A. 2008;483–484:325–8. https://doi.org/10.1016/j.msea.2006.12.179.10.1016/j.msea.2006.12.179 ↗
42. Zhang XZ, Knott JF. Cleavage fracture in bainitic and martensitic microstructures. Acta Mater. 1999;47:3483–95.10.1016/S1359-6454(99)00200-1 ↗
43. CEN Workshop Agreement, CWA 15627:2008, Small Punch Test Method for Metallic Materials, 2008.
44. Fleury E, Ha JS. Small punch tests to estimate the mechanical properties of steels for steam power plant: I Mechanical strength. Int J Press Vessel Pip. 1998;75:699–706.10.1016/S0308-0161(98)00074-X ↗
45. Atkins AG, Mai YW, Elastic and plastic fracture, Ellis Horwood/Wiley, UK, 1988.
46. ASTM E1820 - Standard Test Method for Measurement of Fracture Toughness, 2020.
47. Zheng P, Chen R, Liu H, Chen J, Zhang Z, Liu X, Shen Y. On the standards and practices for miniaturized tensile test—a review. Fusion Eng Des. 2020;161:112006. https://doi.org/10.1016/j.fusengdes.2020.112006.10.1016/j.fusengdes.2020.112006 ↗
48. Xu GT, Hao MF, Qiao YK, Zhang YF, Wang G, Zhao MH. Characterization of elastic-plastic properties of surface-modified layers introduced by carburizing. Mech Mater. 2020;144:103364. https://doi.org/10.1016/j.mechmat.2020.103364.10.1016/j.mechmat.2020.103364 ↗
49. Sandor LT, Ferreira I. A model for fracture toughness evaluation of the carburized layer for SAE 5115 steel. Rev Mater. 2006;11:111–24.
50. Asi O. Fatigue failure of a helical gear in a gearbox. Eng Fail Anal. 2006;13:1116–25. https://doi.org/10.1016/j.engfailanal.2005.07.020.10.1016/j.engfailanal.2005.07.020 ↗