journal article·2011-10-24Open access

Influence of Both Stirrup Spacing and Anchorage Performance on Residual Strength of Corroded RC Beams

Wei Dong, Yuki Murakami, Hideki Oshita, Shuichi Suzuki, Tomoaki Tsutsumi

Abstract

In this study, the influences of both stirrup spacing and anchorage performance on the residual strength of corroded RC beams are investigated. With the increase of stirrup spacing, the applied load is easily transferred to the anchorage region, and with the increase of the corrosion ratio of rebar, the mechanism of corroded RC beams shifts from beam action to arch action. In the case of non-uniform corrosion of the main rebar, the maximum deviation ratio of the corrosion ratio of main rebars is over 0.9, and the beam suffers flexural failure due to the yielding of rebars in the extremely corroded region. In the case of uniform corrosion of the main rebars, the maximum deviation ratio of the corrosion ratio of main rebars is below 0.9, and there are two situations. If the bottom portions of the stirrups are sufficient, the applied load is restricted in the support span, and the corroded beam presents a flexural failure mode. On the other hand, if the bottom portions of the stirrups are insufficient, the applied load is transferred to the anchorage, and the corroded beam is inclined to suffer bond failure. Moreover, when the beam suffers bond failure, the residual strength depends on the anchorage performance.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Concrete Corrosion and Durability · Corrosion Behavior and Inhibition · Structural Behavior of Reinforced Concrete

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Faculty of Science and Engineering, Chuo University, Japan.

Department of Civil Engineering, Nagaoka National College of Technology, Japan.

Department of Civil Engineering, Chuo University, Japan.

Tokyo Electric Power Services Co., Ltd, Japan.

Institute for Technology Development, Tokyo Electric Power Co., Ltd, Japan.

References (16)

Show source-provided references
1. Aoyama, T., Shimomura, T. and Maruyama, H., (1998). “Characteristics of flexural failure of corroded RC beam by salt damage.” Proceedings of the Japan Concrete Institute, 20(2), 883-888. (in Japanese)
2. Ikeda, S., Bui, B. D. and Uji, K., (1979). “On the shear mechanism of RC beams.” Proceedings of the Japan Concrete Institute, 1(1), 317-320. (in Japanese)
3. Iwanami, M., Yokoda, H. and Satou, F., (2002). “Influence of corrosion on load capacity for RC beams.” Proceedings of the Japan Concrete Institute, 24(2), 1501-1506. (in Japanese)
4. JSCE, (2006). “Structural performance for degraded concrete structures series 71.” Tokyo: Japan Society of Civil Engineers.
5. Kani, G. N. J., (1964). “The riddle of shear failure and its solution.” Journal of ACI, 61(4), 441-468.
6. Kato, E., Iwanami, M., Ito, H. and Yokoda, H., (2003). “Influence of corrosion on flexural capacity for corroded RC beam subjected to cyclic flexural loading.” Proceedings of the Japan Concrete Institute, 25(2), 1849-1854. (in Japanese)
7. Kayser, J. and Nowak, A., (1989). “Capacity loss due to corrosion in steel-girder bridges.” ASCE, 115(6), 1525-1537.10.1061/(ASCE)0733-9445(1989)115:6(1525) ↗
8. Kim, H., Noguchi, T. and Nagai, H., (2007). “Evaluation of mechanical performance of corroded rebar considering the surface shape.” Proceedings of the Japan Concrete Institute, 29(1), 1395-1400. (in Japanese)
9. Lee, H. S., Tomosawa, F. and Noguchi, T., (1995). “Effect of corrosion of reinforcing bar on the structural performance of single reinforced beam.” Cement Science and Concrete Technology, 49, 732-737. (in Japanese)
10. Murakami, Y., Kinoshita, T., Suzuki, S., Fukumoto, Y. and Oshita H., (2006). “Study on the residual strength for corroded RC reinforced beam.” Concrete Research and Technology, 17(1), 61-74. (in Japanese)10.3151/crt1990.17.1_61 ↗
11. Murakami, Y., Yamauchi, Y., Tsutsumi, T. and Ohshita, H., (2006). “Study on influence of stirrup on residual strength for corroded RC reinforced beam.” Proceedings of the Japan Concrete Institute, 28(2), 727-732. (in Japanese)
12. Oyado, S., Nishiwa, K., Kasegawa, M. and Nakaoka, T., (2001). “Corrosion pattern and ultimate load for RC beams long term exposure to atmosphere.” Proceedings of the Japan Concrete Institute, 23(3), 315-1320. (in Japanese)
13. Scott, R. H. (1996). “Intrinsic mechanisms in reinforced concrete beam-column connection behaviour.” ACI Structural Journal, 93(3), 336-346.
14. Val, D. and Chernin, L., (2009). “Serviceability reliability of reinforced concrete beams with corroded reinforcement.” Journal of Structural Engineering, 135(8), 896-905.10.1061/(ASCE)0733-9445(2009)135:8(896) ↗
15. Wang, X. and Li, X., (2010). “Simplified methodology for the evaluation of the residual strength of corroded reinforced concrete beams.” Journal of Performance of Constructed Facilities, 24(2), 108-119.10.1061/(ASCE)CF.1943-5509.0000083 ↗
16. Xue, X. and Seki, H., (2010). “Influence of longitudinal bar corrosion on shear behavior of RC beams.” Journal of Advanced Concrete Technology, 8(2), 145-156.10.3151/jact.8.145 ↗