Abrasion Resistance Improvement of Recycled Aggregate Pervious Concrete with Granulated Blast Furnace Slag and Copper Slag
Source abstract
Abstract
The poor abrasion resistance of recycled aggregate pervious concrete (RAPC) limits its application. Granulated blast furnace slag (GBFS) and copper slag (CS) were used as mineral admixtures to replace cement in RAPC for improving the abrasion resistance. At the 10% GBFS replacement level, 5% to 25% of CS was added in RAPC respectively, which reduced the consumption of the cement. The effects of GBFS and CS on paste fluidity, porosity, permeability, compressive strength and abrasion resistance were evaluated. RAPC exhibited an excellent abrasion resistance after adding GBFS and CS. In this case, 10% blended amount was the optimal amount of GBFS and CS. Compared with the single cement group, the abrasion resistance increased by 38.78%, which is mainly because the fayalite in CS supplies good abrasion resistance, whereas the GBFS also plays an important role. The mechanism was studied via X-ray diffraction analysis and microhardness. The porosity and permeability of the RAPC increased with the CS replacement level. Moreover, the leaching concentration of heavy metal ions in the prepared RAPC was significantly low, indicating that RAPC could be applied safely. The results not only provides a feasible technical means for the large-scale utilisation of CS but also presents a theoretical basis for the improvement of RAPC abrasion resistance.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Recycled Aggregate Concrete Performance · Urban Stormwater Management Solutions · Innovative concrete reinforcement materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
State Key Laboratory of Silicate Materials for Architectures, Wuhan University of Technology, Wuhan 430070, PR China.
China Building Materials Academy, Beijing 100034, PR China.
References (53)
Show source-provided references
1. 1) Al-Jabri, K. S., Taha, R. A. and Al-Ghassani, M., (2002). “Use of copper slag and cement by-pass dust as cementitious materials.” Cement, Concrete and Aggregates, 24(1), 7-12.10.1520/CCA10485J ↗
2. 2) Al-Jabri, K. S., Al-Saidy, A. H. and Taha, R. A., (2011). “Effect of copper slag as a fine aggregate on the properties of cement mortars and concrete.” Construction and Building Materials, 25(2), 933-938.10.1016/j.conbuildmat.2010.06.090 ↗
3. 3) Al-Jabri, K. S., Hisada, M., Al-Saidy, A. H. and Al-Oraimi, S. K., (2009). “Performance of high strength concrete made with copper slag as a fine aggregate.” Construction and Building Materials, 23(6), 2132-2140.10.1016/j.conbuildmat.2008.12.013 ↗
4. 4) Al-Jabri, K. S., Taha, R. A., Al-Hashmi, A. and Al-Harthy, A. S., (2006). “Effect of copper slag and cement by-pass dust addition on mechanical properties of concrete.” Construction and Building Materials, 20(5), 322-331.10.1016/j.conbuildmat.2005.01.020 ↗
5. 5) Alderete, N., Villagrán, Y., Mignon, A., Snoeck, D. and De Belie, N., (2017). “Pore structure description of mortars containing ground granulated blast-furnace slag by mercury intrusion porosimetry and dynamic vapour sorption.” Construction and Building Materials, 145, 157-165.10.1016/j.conbuildmat.2017.03.245 ↗
6. 6) Aliabdo, A. A., Abd Elmoaty, A. E. M. and Fawzy, A. M., (2018). “Experimental investigation on permeability indices and strength of modified pervious concrete with recycled concrete aggregate.” Construction and Building Materials, 193, 105-127.10.1016/j.conbuildmat.2018.10.182 ↗
7. 7) Angulo-Ramírez, D. E., Mejía de Gutiérrez, R. and Puertas, F., (2017). “Alkali-activated Portland blast-furnace slag cement: Mechanical properties and hydration.” Construction and Building Materials, 140, 119-128.10.1016/j.conbuildmat.2017.02.092 ↗
8. 8) Bhutta, M. A. R., Hasanah, N., Farhayu, N., Hussin, M. W., Tahir, M. B. M. and Mirza, J., (2013). “Properties of porous concrete from waste crushed concrete (recycled aggregate).” Construction and Building Materials, 47, 1243-1248.10.1016/j.conbuildmat.2013.06.022 ↗
9. 9) Bilir, T., Yüksel, I., Topcu, I. B. and Gencel, O., (2017). “Effects of bottom ash and granulated blast furnace slag as fine aggregate on abrasion resistance of concrete.” Science and Engineering of Composite Materials, 24(2), 261-269.10.1515/secm-2015-0101 ↗
10. 10) Brake, N. A., Allahdadi, H. and Adam, F., (2016). “Flexural strength and fracture size effects of pervious concrete.” Construction and Building Materials, 113, 536-543.10.1016/j.conbuildmat.2016.03.045 ↗
11. 11) Cai, L., Li, X., Liu, W., Ma, B. and Lv, Y., (2019). “The slurry and physical-mechanical performance of autoclaved aerated concrete with high content solid wastes: Effect of grinding process.” Construction and Building Materials, 218, 28-39.10.1016/j.conbuildmat.2019.05.107 ↗
12. 12) Chindaprasirt, P., Hatanaka, S., Chareerat, T., Mishima, N. and Yuasa, Y., (2008). “Cement paste characteristics and porous concrete properties.” Construction and Building Materials, 22(5), 894-901.10.1016/j.conbuildmat.2006.12.007 ↗
13. 13) Constantinides, G. and Ulm, F.-J., (2007). “The nanogranular nature of C–S–H.” Journal of the Mechanics and Physics of Solids, 55(1), 64-90.10.1016/j.jmps.2006.06.003 ↗
14. 14) El-Hassan, H., Kianmehr, P. and Zouaoui, S., (2019). “Properties of pervious concrete incorporating recycled concrete aggregates and slag.” Construction and Building Materials, 212, 164-175.10.1016/j.conbuildmat.2019.03.325 ↗
15. 15) Feng, Y., Chen, Q., Zhou, Y., Yang, Q., Zhang, Q., Jiang, L. and Guo, H., (2020). “Modification of glass structure via CaO addition in granulated copper slag to enhance its pozzolanic activity.” Construction and Building Materials, 240, Article ID 117970.10.1016/j.conbuildmat.2019.117970 ↗
16. 16) Gaedicke, C., Marines, A. and Miankodila, F., (2014). “Assessing the abrasion resistance of cores in virgin and recycled aggregate pervious concrete.” Construction and Building Materials, 68, 701-708.10.1016/j.conbuildmat.2014.07.001 ↗
17. 17) Gao, W., Jian, S., Li, B., Li, X., Tan, H., Huang, W. and Yang, X., (2020). “Solidification of zinc in lightweight aggregate produced from contaminated soil.” Journal of Cleaner Production, 265, Article ID 121784.10.1016/j.jclepro.2020.121784 ↗
18. 18) Gesoğlu, M., Güneyisi, E., Khoshnaw, G. and İpek, S., (2014). “Abrasion and freezing-thawing resistance of pervious concretes containing waste rubbers.” Construction and Building Materials, 73, 19-24.10.1016/j.conbuildmat.2014.09.047 ↗
19. 19) Gorai, B., Jana, R. K. and Premchand., (2003). “Characteristics and utilisation of copper slag - A review.” Resources, Conservation and Recycling, 39(4), 299-313.10.1016/S0921-3449(02)00171-4 ↗
20. 20) He, Z., Chen, X. and Cai, X., (2019). “Influence and mechanism of micro/nano-mineral admixtures on the abrasion resistance of concrete.” Construction and Building Materials, 197, 91-98.10.1016/j.conbuildmat.2018.11.224 ↗
21. 21) Jennings, H. M., (2000). “A model for the microstructure of calcium silicate hydrate in cement paste.” Cement and Concrete Research, 30(1), 101-116.10.1016/S0008-8846(99)00209-4 ↗
22. 22) Jian, S., Gao, W., Lv, Y., Tan, H., Li, X., Li, B. and Huang, W., (2020). “Potential utilization of copper tailings in the preparation of low heat cement clinker.” Construction and Building Materials, 252, Article ID 119130.10.1016/j.conbuildmat.2020.119130 ↗
23. 23) Jiang, D., Li, X., Jiang, W., Li, C., Lv, Y. and Zhou, Y., (2020a). “Effect of tricalcium aluminate and sodium aluminate on thaumasite formation in cement paste.” Construction and Building Materials, 259, Article ID 119842.10.1016/j.conbuildmat.2020.119842 ↗
24. 24) Jiang, W., Li, X., Lv, Y., Jiang, D., Liu, Z. and He, C., (2020b). “Mechanical and hydration properties of low clinker cement containing high volume superfine blast furnace slag and nano silica.” Construction and Building Materials, 238, Article ID 117683.10.1016/j.conbuildmat.2019.117683 ↗
25. 25) Kajaste, R. and Hurme, M., (2016). “Cement industry greenhouse gas emissions – Management options and abatement cost.” Journal of Cleaner Production, 112, 4041-4052.10.1016/j.jclepro.2015.07.055 ↗
26. 26) Kumar, R., (2017). “Influence of recycled coarse aggregate derived from construction and demolition waste (CDW) on abrasion resistance of pavement concrete.” Construction and Building Materials, 142, 248-255.10.1016/j.conbuildmat.2017.03.077 ↗
27. 27) Li, B., Jian, S., Zhu, J., Yu, H., Wu, R., Gao, W. and Tan, H., (2020a). “Effect of flux components of lightweight aggregate on physical properties and heavy metal solidification performance.” Waste Management, 118, 131-138.10.1016/j.wasman.2020.08.025 ↗
28. 28) Li, B., Wang, L., Jian, S., Zhang, J., Gao, W., Zhu, J. and Wu, R., (2021). “Leaching behavior of copper and chromium in the mortar containing artificial fine aggregate prepared by contaminated soil.” Construction and Building Materials, 270, Article ID 121367.10.1016/j.conbuildmat.2020.121367 ↗
29. 29) Li, H., Xu, D., Feng, S. and Shang, B., (2014). “Microstructure and performance of fly ash micro-beads in cementitious material system.” Construction and Building Materials, 52, 422-427.10.1016/j.conbuildmat.2013.11.040 ↗
30. 30) Li, X., He, C., Lv, Y., Jian, S., Liu, G., Jiang, W. and Jiang, D., (2020b). “Utilization of municipal sewage sludge and waste glass powder in production of lightweight aggregates.” Construction and Building Materials, 256, Article ID 119413.10.1016/j.conbuildmat.2020.119413 ↗
31. 31) Liu, T., Wang, Z., Zou, D., Zhou, A. and Du, J., (2019). “Strength enhancement of recycled aggregate pervious concrete using a cement paste redistribution method.” Cement and Concrete Research, 122, 72-82.10.1016/j.cemconres.2019.05.004 ↗
32. 32) Lori, A. R., Hassani, A. and Sedghi, R., (2019). “Investigating the mechanical and hydraulic characteristics of pervious concrete containing copper slag as coarse aggregate.” Construction and Building Materials, 197, 130-142.10.1016/j.conbuildmat.2018.11.230 ↗
33. 33) Lye, C.-Q., Koh, S.-K., Mangabhai, R. and Dhir, R. K., (2015). “Use of copper slag and washed copper slag as sand in concrete: A state-of-the-art review.” Magazine of Concrete Research, 67(12), 665-679.10.1680/macr.14.00214 ↗
34. 34) Ni, T., Ma, W., Yang, Y., Yu, J., Liu, J., Jiang, C. and Gu, C., (2021). “Interface reinforcement and a new characterization method for pore structure of pervious concrete.” Construction and Building Materials, 267, Article ID 121052.10.1016/j.conbuildmat.2020.121052 ↗
35. 35) Pan, G., Sun, W., Ding, D. and Zhang, Y., (1998). “Experimental study on the micro-aggregate effect in high-strength and super-high-strength cementitious composites (Communicated by D. M. Roy).” Cement and Concrete Research, 28(2), 171-176.10.1016/S0008-8846(97)00248-2 ↗
36. 36) Panda, S., Sarkar, P. and Davis, R., (2020). “Abrasion resistance and slake durability of copper slag aggregate concrete.” Journal of Building Engineering, Article ID 101987.10.1016/j.jobe.2020.101987 ↗
37. 37) Rehder, B., Banh, K. and Neithalath, N., (2014). “Fracture behavior of pervious concretes: The effects of pore structure and fibers.” Engineering Fracture Mechanics, 118, 1-16.10.1016/j.engfracmech.2014.01.015 ↗
38. 38) Shanmuganathan, P., Lakshmipathiraj, P., Srikanth, S., Nachiappan, A. L. and Sumathy, A., (2008). “Toxicity characterization and long-term stability studies on copper slag from the ISASMELT process.” Resources, Conservation and Recycling, 52(4), 601-611.10.1016/j.resconrec.2007.08.001 ↗
39. 39) Shi, C., Meyer, C. and Behnood, A., (2008). “Utilization of copper slag in cement and concrete.” Resources,Conservation and Recycling, 52(10), 1115-1120.10.1016/j.resconrec.2008.06.008 ↗
40. 40) Simmons, C. T., (2008). “Henry Darcy (1803–1858): Immortalised by his scientific legacy.” Hydrogeology Journal, 16(6), 1023.10.1007/s10040-008-0304-3 ↗
41. 41) Singh, S. P., Tripathy, D. P. and Ranjith, P. G., (2008). “Performance evaluation of cement stabilized fly ash-GBFS mixes as a highway construction material.” Waste Management, 28(8), 1331-1337.10.1016/j.wasman.2007.09.017 ↗
42. 42) Sorelli, L., Constantinides, G., Ulm, F.-J. and Toutlemonde, F., (2008). “The nano-mechanical signature of ultra high performance concrete by statistical nanoindentation techniques.” Cement and Concrete Research, 38(12), 1447-1456.10.1016/j.cemconres.2008.09.002 ↗
43. 43) Tan, H., Deng, X., He, X., Zhang, J., Zhang, X., Su, Y. and Yang, J., (2019a). “Compressive strength and hydration process of wet-grinded granulated blast-furnace slag activated by sodium sulfate and sodium carbonate.” Cement and Concrete Composites, 97, 387-398.10.1016/j.cemconcomp.2019.01.012 ↗
44. 44) Tan, H., Nie, K., He, X., Guo, Y., Zhang, X., Deng, X., Su, Y. and Yang, J., (2019b). “Effect of organic alkali on compressive strength and hydration of wet-grinded granulated blast-furnace slag containing Portland cement.” Construction and Building Materials, 206, 10-18.10.1016/j.conbuildmat.2019.02.028 ↗
45. 45) Torskaya, T., Shabro, V., Torres-Verdín, C., Salazar-Tio, R. and Revil, A., (2014). “Grain shape effects on permeability, formation factor, and capillary pressure from pore-scale modeling.” Transport in Porous Media, 102(1), 71-90.10.1007/s11242-013-0262-7 ↗
46. 46) Velez, K., Maximilien, S., Damidot, D., Fantozzi, G. and Sorrentino, F., (2001). “Determination by nanoindentation of elastic modulus and hardness of pure constituents of Portland cement clinker.” Cement and Concrete Research, 31(4), 555-561.10.1016/S0008-8846(00)00505-6 ↗
47. 47) Xiao, J., Li, W., Sun, Z., Lange, D. A. and Shah, S. P., (2013). “Properties of interfacial transition zones in recycled aggregate concrete tested by nanoindentation.” Cement and Concrete Composites, 37, 276-292.10.1016/j.cemconcomp.2013.01.006 ↗
48. 48) Yang, L., Kou, S., Song, X., Lu, M. and Wang, Q., (2020). “Analysis of properties of pervious concrete prepared with difference paste-coated recycled aggregate.” Construction and Building Materials, 269, Article ID 121244.10.1016/j.conbuildmat.2020.121244 ↗
49. 49) Yap, S. P., Chen, P. Z. C., Goh, Y., Ibrahim, H. A., Mo, K. H. and Yuen, C. W., (2018). “Characterization of pervious concrete with blended natural aggregate and recycled concrete aggregates.” Journal of Cleaner Production, 181, 155-165.10.1016/j.jclepro.2018.01.205 ↗
50. 50) Yu, F., Sun, D., Hu, M. and Wang, J., (2019). “Study on the pores characteristics and permeability simulation of pervious concrete based on 2D/3D CT images.” Construction and Building Materials, 200, 687-702.10.1016/j.conbuildmat.2018.12.135 ↗
51. 51) Zhang, J., Tan, H., He, X., Yang, W. and Deng, X., (2020). “Utilization of carbide slag-granulated blast furnace slag system by wet grinding as low carbon cementitious materials.” Construction and Building Materials, 249, Article ID 118763.10.1016/j.conbuildmat.2020.118763 ↗
52. 52) Zhang, J., Tan, H., He, X., Zhao, R., Yang, J. and Su, Y., (2021). “Nano particles prepared from hardened cement paste by wet grinding and its utilization as an accelerator in Portland cement.” Journal of Cleaner Production, 283, Article ID 124632.10.1016/j.jclepro.2020.124632 ↗
53. 53) Zhang, Z., Zhang, Y., Yan, C. and Liu, Y., (2017). “Influence of crushing index on properties of recycled aggregates pervious concrete.” Construction and Building Materials, 135, 112-118.10.1016/j.conbuildmat.2016.12.203 ↗