Prediction of Drying Shrinkage Cracking of Eco-efficient Steel Chip Reinforced Cementitious Composite Considering Tensile Creep
Source abstract
Abstract
This paper reports on the characteristics of drying shrinkage and creep of steel chip reinforced cementitious composite (SCRCC). In this study, first, four restrained wall specimens made of normal mortar and SCRCC with various numbers of steel reinforcing bars (4 or 10) were prepared to compare drying shrinkage characteristics. The specimens were re-strained on the rigid laboratory floor so that shrinkage cracks were induced. The drying shrinkage strains were measured by the contact gauge method and compared with unrestrained small specimens. The number of cracks was simultane-ously observed. Second, bond tests were prepared to evaluate the bond characteristics between the SCRCC and the steel bar. Third, creep tests were performed to improve the accuracy of the analysis of the drying shrinkage behavior. Twelve block specimens were made and a constant flexural load was applied for 7, 14, and 28 days. The observed shrinkage strains and creep strains of SCRCC were modeled according to CEB-FIP Model Code 1990. These models were incor-porated with bond computation between the SCRCC and the steel bar to predict the number of drying shrinkage cracks. The computed equivalent number of cracks based on the shrinkage strain model, the creep model, and the bond model derived from a pull-out test generally agreed with the test results.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Innovative concrete reinforcement materials · Structural Behavior of Reinforced Concrete · Concrete and Cement Materials Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Architecture and Architectural Engineering, Kyoto University, Kyoto, Japan.
Nexco-West, Osaka, Japan.
References (17)
Show source-provided references
1. 1) Architectural Institute of Japan, (2008). “Recommendations for environmentally conscious practice of reinforced concrete buildings.” (in Japanese)
2. 2) Alwaeli, M. and Nadziakiewicz, J., (2012). “Recycling of scale and steel chips waste as a partial replacement of sand in concrete.” Construction and Building Materials, 28(1), 157-163.10.1016/j.conbuildmat.2011.08.047 ↗
3. 3) CEB-FIP, (1990). “Model code for concrete structures.” fib, (2010). “fib Model Code 2010,” 233-239.
4. 4) Hong, S., Kimura, S., Tanaka, D., Sato, Y. and Kaneko, Y., (2014). “Drying shrinkage and creep characteristics of steel chip reinforced cementitious composite.” Proceedings of Annual Research Meeting, Materials and Construction, Kinki Branch, Architectural Institute of Japan, 54, 9-20. (in Japanese)
5. 5) Kanada, M., Sato, Y. and Kaneko, Y., (2011). “Seismic retrofit of exposed column basement using steel chip reinforced cementitious composite.” Proceedings of Constructional Steel, 19, 155-162. (in Japanese)
6. 6) Keoleian, G. A., Kendall, A., Dettling, J. E., Smith, V. M., Chandler, R., Lepech, M. D. and Li, V. C, (2005). “Life cycle modeling of concrete bridge design: Comparison of engineered cementitious composite link slabs and conventional steel expansion joints.” Journal of Infrastructure Systems, 11(1), 51-60.10.1061/(ASCE)1076-0342(2005)11:1(51) ↗
7. 7) Kheder, G. F., (1997). “A new look at the control of volume change cracking of base-restrained concrete walls.” ACI Structural Journal, 94(3), 262-270.
8. 8) Kojima, K. and Nakamura, N., (2008). “Experiment of tensile creep and tensile relaxation for high strength mortar in early age.” Proceedings of the Japan Concrete Institute, 30(1), 441-446. (in Japanese)
9. 9) Koyanagi, M., Masuda, Y. and Nakane, S., (1990). “A study on shrinkage cracks in reinforced concrete walls (Part 4) -Prediction analysis of cracking widths due to restrained volume change in one-way concrete members-.” Report of Obayashi Corporation Technical Research Institute, 41, 73-79. (in Japanese)
10. 10) Kumano, T., Nishibayashi, S., Inoue, S. and Yoshino, A., (1999). “A study on the prediction model of tensile creep strain of concrete based on micro pore behavior.” Journal of Japan Society of Civil Engineers, 42(613), 121-135.10.2208/jscej.1999.613_121 ↗
11. 11) Ranaivomanana, N., Multon, S. and Turatsinze, A., (2013). “Tensile, compressive and flexural basic creep of concrete at different stress levels.” Cement and Concrete Research, 52, 1-10.10.1016/j.cemconres.2013.05.001 ↗
12. 12) Rehm, G., (1961). “Über die Grundlagen des Verbundes zwischen Stahl und Beton,” Deutscher Ausshcuss für Stahlbeton, Nr. 138.
13. 13) Sahmaran, M., Li, V. C. and Andrade, C., (2008). “Corrosion resistance performance of steel reinforced engineered cementitious composite beams.” ACI Materials Journal, 105(3), 243-250.
14. 14) Swamy, R. N. and Stavrides, H., (1979). “Influence of fiber reinforcement on restrained shrinkage and cracking.” ACI Journal, 94(3), 262-270.
15. 15) Watanabe, Y., Wakatsuki, T., Sato, H. and Maruyama, T., (2005). “Development of Fe-Mn-Si-Cr shape memory alloy fiber reinforced plaster-based smart composites.” Materials Science Forum, 475, 2063-2066.
16. 16) Yannapouos, P. J. and Tassios, T. P., (1991). “Reinforced concrete axial elements analyzed under monotonic and cyclic actions.” ACI Structural Journal, 8(1), 3-11.
17. 17) Zainab, Z. I. and Enas, A. A., (2008). “Reuse of waste iron as a partial replacement of sand in Cconcrete.” Waste Management, 28(11), 2048-2053.10.1016/j.wasman.2007.07.009 ↗