Probing the Effects of Density on Combustion Performance of Cement-bonded Particleboard Produced from Wood Processing Residues
Source abstract
Abstract
The purpose of this study was to provide insights into deeper understanding of the combustion performance of cement-bonded particleboards. Cement-bonded particleboard produced from Chinese fir processing residues is fabricated and its combustion performance is further evaluated by cone calorimeter analysis. Obtained results revealed that combustion performance of cement-bonded particleboard positively depends on the density of which, and higher density imparts corresponding particleboards reduction in heat release rate, total heat release, and mass loss rate, along with elevated time to ignition. With the density of particleboard increasing from 0.7 to 1.0 g/cm3, peak and average heat release rate, total heat release and average mass loss rate of specimens were decreased by 55.9, 73.4, 77.8 and 60.3%, respectively. Furthermore, time to ignition of particleboard increased by more than 20 times as the density increasing. Residual mass of specimens was also remarkably elevated along with higher yields of CO and CO2 as the density of particleboard increasing. We believe that proposed investigation is beneficial for the value-added utilization of wood processing residues and further developing products fabricated by wood processing residues.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Natural Fiber Reinforced Composites · Fire dynamics and safety research · Lignin and Wood Chemistry
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
School of Engineering, Zhejiang Agriculture & Forestry University, Lin’an 311300, China.
References (40)
Show source-provided references
1. 1) Atoyebi, O. D., Awolusi, T. F. and Davies, I. E. E., (2018). “Artificial neural network evaluation of cement-bonded particle board produced from red iron wood (Lophira alata) sawdust and palm kernel shell wastes.” Case Studies in Construction Materials, 9, Article ID e00185.10.1016/j.cscm.2018.e00185 ↗
2. 2) Babaauskas, V. and Parker, W. J., (1978). “Ignitability measurements with the cone calorimeter.” Fire and Materials, 11(1), 31-43.10.1002/fam.810110103 ↗
3. 3) Dong, Z. Q., Yu, Y. M. and Song, P. A., (2016). “Effects of two types of waste wood species on the hydration characteristics of Portland cement.” Journal of Advanced Concrete Technology, 14(1), 13-20.10.3151/jact.14.13 ↗
4. 4) Esmeralda, Y. A. O., Mário, R. S. and Marcos, A. E. S., (2005). “Physico-mechanical properties and decay resistance of Cupressus spp. cement bonded particleboard.” Cement and Concrete Composites, 27(3), 333-338.10.1016/j.cemconcomp.2004.02.046 ↗
5. 5) Fan, M. Z., Bonfield, P. W. and Dinwooddie, J. M., (2000). “Dimensional instability of cement bonded particleboard: SEM and image analysis.” Journal of Materials Science, 35, 6213- 6220.10.1023/A:1026733313070 ↗
6. 6) Frybort, S., Mauritz, R. and Teischinger, A., (2008). “Cement bonded composites - A mechanical review.” BioResources, 3(2), 602-626.10.15376/biores.3.2.602-626 ↗
7. 7) Gong, A. and Harichandran, R. S., (2012). “Wood-cement particleboard: Impact behavior and potential application in crash barriers.” Journal of Materials in Civil Engineering, 42(1), 134-140.10.1061/(ASCE)MT.1943-5533.0000363 ↗
8. 8) Harada, T., (2001). “Time to ignition, heat release rate and fire endurance time of wood in cone calorimeter test.” Fire and Materials, 25(4), 161-167.10.1002/fam.766 ↗
9. 9) Hossain, M. D., Wang, L. and Yu, I. K. M., (2018). “Environmental and technical feasibility study of upcycling wood waste into cement-bonded particleboard.” Construction and Building Materials, 173, 474-480.10.1016/j.conbuildmat.2018.04.066 ↗
10. 10) Hou, J. F., Lu, K. Y. and Cai, Z. Y., (2017). “Cone calorimeter evaluation of reinforced hybrid wood-aluminum composites.” Journal of Fire Sciences, 35(2), 118-131.10.1177/0734904116683717 ↗
11. 11) ISO, (2015). “Reaction to fire tests-heat release, smoke production and mass loss rate - Part 1: Heat release rate (Cone calorimeter method) and smoke production rate (dynamic measurement) (ISO Standard 5660-1-2015).” Geneva: International Organization for Standardization.
12. 12) Jorge, F. C., Pereira, C. and Ferreira, J. M. F., (2004). “Wood-cement composites: A review.” European Journal of Wood and Wood Products, 62, 370-377.10.1007/s00107-004-0501-2 ↗
13. 13) Kong, L. J., Xiong, Y. and Liu, T., (2016). “Effect of fiber natures on the formation of solid bridge for preparing wood sawdust derived biomass pellet fuel.” Fuel Processing Technology, 144, 79-84.10.1016/j.fuproc.2015.12.001 ↗
14. 14) Kuka, E., Cirule, D. and Kajaks, J., (2016). “Fungal degradation of wood plastic composites made with thermally modified wood residues.” Key Engineering Materials, 72, 8-12.10.4028/www.scientific.net/KEM.721.8 ↗
15. 15) Lee, B. H., Kim, H. S. and Kim, S., (2011). “Evaluating the flammability of wood-based panels and gypsum particleboard using a cone calorimeter.” Construction and Building Materials, 25(5), 3044-3050.10.1016/j.conbuildmat.2011.01.004 ↗
16. 16) Liu, Y. T., (2011). “Cone calorimeter analysis on the fire-resistant properties of FRW fire-retardant particleboard.” Advanced Materials Research, 311-313, 2142-2145.10.4028/www.scientific.net/AMR.311-313.2142 ↗
17. 17) López, F. A., Centeno, T. A. and García-Díaz, I., (2013). “Textural and fuel characteristics of the chars produced by the pyrolysis of waste wood, and the properties of activated carbons prepared from them.” Journal of Analytical and Applied Pyrolysis, 104, 551-558.10.1016/j.jaap.2013.05.014 ↗
18. 18) Mouritz, A. P., Mathys, Z. and Gibson, A. G., (2006). “Heat release of polymer composites in fire.” Composites Part A: Applied Science and Manufacturing, 37(7), 1040-54.10.1016/j.compositesa.2005.01.030 ↗
19. 19) Nasser, R. A., Al-Mefarrej, H. A. and Abdel-Aal, M. A., (2014). “Effects of tree species and wood particle size on the properties of cement-bonded particleboard manufacturing from tree pruning.” Journal of Environmental Biology, 35(5), 961-971.
20. 20) Nazerian, M., Ghalehno, M. D. and Gozali, E., (2011). “Effects of wood species, particle sizes and dimensions of waste obtained from trimming of wood-cement composites on physical and mechanical properties of cement-bonded particleboard.” Wood Material Science and Engineering, 6(5), 196-206.10.1080/17480272.2011.601816 ↗
21. 21) Nazerian, M. and Eghbal, S. H., (2013). “The influence of additive content and particle size of bagasse on some properties of cement-bonded particleboard.” Journal of Indian Academy of Wood Science, 10(2), 86-94.10.1007/s13196-013-0099-2 ↗
22. 22) Nta, S. A. and Olorunnisola, A. O., (2016). “Experimental production and evaluation of cement-bonded composite pipes for water conveyance.” International Journal of Composite Materials, 6(1), 9-14.
23. 23) Odeyemi, S. O., Abdulwahab, R., Adeniyi, A. G. and Atoyebi, O. D., (2020). “Physical and mechanical properties of cement-bonded particle board produced from African balsam tree (Populous Balsamifera) and periwinkle shell residues.” Results in Engineering, 6, Article ID 00126.10.1016/j.rineng.2020.100126 ↗
24. 24) Okino, E. Y. A., Souza, M. R. and Santana, M. A. E., (2005). “Physico-mechanical properties and decay resistance of Cupressus spp. cement-bonded particleboards.” Cement and Concrete Composites, 27(3), 333-338.10.1016/j.cemconcomp.2004.02.046 ↗
25. 25) Olorunnisola, A. O. and Adejisan, O. O., (2002). “Trial production and testing of CBPB from rattan furniture waste.” Wood and Fiber Science, 34(1), 116-124.
26. 26) Papadopoulos, A. N., (2008). “Mechanical properties and decay resistance of Hornbeam cement bonded particleboards.” Research Letters in Materials Science, 2008, Article ID 379749.10.1155/2008/379749 ↗
27. 27) Pedieu, R., Koubaa, A. and Riedl, B., (2012). “Fire-retardant properties of wood particleboards treated with boric acid.” European Journal of Wood and Wood Products, 70, 191-197.10.1007/s00107-011-0538-y ↗
28. 28) PRC, (2008). “Requirements and mark on burning behavior of fire retarding products and subassemblies in public place (National Standard GB/T 20286-220 of the Peoples Republic of China).” Beijing: Standardization Administration of China. (in Chinese)
29. 29) Raúl, E. H. and Cloutier, A., (2011). “Physical and mechanical properties of gypsum particleboard reinforced with Portland cement.” European Journal of Wood and Wood Products, 69, 247-254.10.1007/s00107-010-0434-x ↗
30. 30) Sarkar, M., Asaduzzaman, M. and Das, A. K., (2012). “Mechanical properties and dimensional stability of cement bonded particleboard from rice husk and sawdust.” Bangladesh Journal of Scientific and Industrial Research, 47(3), 273-278.10.3329/bjsir.v47i3.13060 ↗
31. 31) Souza, A. M., Nascimento, M. F. and Almeida, D. H., (2018). “Wood-based composite made of wood waste and epoxy-based ink-waste as adhesive: A cleaner production alternative.” Journal of Cleaner Production, 193, 549-562.10.1016/j.jclepro.2018.05.087 ↗
32. 32) Tabarsa, T. and Ashori, A., (2011). “Dimensional stability and water uptake properties of cement-bonded wood composites.” Journal of Polymers and the Environment, 19, 518-521.10.1007/s10924-011-0295-3 ↗
33. 33) Wang, L., Chen, S. S. and Tsang, D. C. W., (2016). “Value-added recycling of construction waste wood into noise and thermal insulating cement-bonded particleboards.” Construction and Building Materials, 125, 316-325.10.1016/j.conbuildmat.2016.08.053 ↗
34. 34) Wang, S. Y., Yang, T. H. and Lin, L. T., (2008). “Fire-retardant-treated low-formaldehyde-emission particleboard made from recycled wood-waste.” Bioresource Technology, 99, 2072-2077.10.1016/j.biortech.2007.03.047 ↗
35. 35) Wang, X. and Yu, Y. M., (2012). “The compatibility of two common fast-growing species with Portland cement.” Journal of the Indian Academy of Wood Science, 9(2), 154-159.10.1007/s13196-012-0081-4 ↗
36. 36) Winandy, J. E., Wang, Q. W. and White, R. H., (2008). “Fire-retardant-treated strandboard: Properties and fire performance.” Wood and Fiber Science, 40(1), 62-71.
37. 37) Xu, Y., Du, X. Z., Qi, Y. J., Ma, L. and Zheng, G., (2015). “Utilization of wood processing wastes.” China Forest Products Industry, 42(5), 40-44. (in Chinese)
38. 38) Yel, H., Cavdar, A. D. and Totun, S. B., (2020). “Effect of press temperature on some properties of cement-bonded particleboard.” Maderas: Ciemcia y Technología, 22(1), 83-92.10.4067/S0718-221X2020005000108 ↗
39. 39) Yilmaz, M., Yaman, I. O. and Tokyay, M., (2016). “Cement production by cement-bonded particleboard wastes.” Advances in Cement Research, 28(4), 233-240.10.1680/jadcr.15.00023 ↗
40. 40) Yu, Y. M., Hou, J. F., Dong, Z. Q., Wang, C., Lu, F. Z. and Song, P. A., (2016). “Evaluating the flammability performance of Portland cement-bonded particleboards with different cement-wood ratios using a cone calorimeter.” Journal of Fire Sciences, 34(3), 199-211.10.1177/0734904116630758 ↗