Solid epoxy for functional 3D printing with isotropic mechanical properties by material extrusion
Source abstract
Abstract
Material extrusion is the most commonly used additive manufacturing process. However, currently it is mainly applied for the production of prototypes or simple jigs and fixtures due to issues with anisotropic material behavior. Diffusion and entanglement of the polymer chains is limited between the layers and among the infill lines within a layer of the usually thermoplastic material as it solidifies immediately after deposition. This results in weak bonding leading to a reduced load-bearing capacity. In this study, a thermosetting polymer is developed and presented. It enables cross-linking over the interfaces between the infill lines and layers during post-curing which resolves this issue. The formulation is based on a solid epoxy resin, allowing it to be processed in filament form and a latent curing agent preventing it from curing within the hotend and ensuring a suitable shelf life. To benchmark the newly developed material it is compared to casted and milled bulk specimens and 3D printed specimens with commercial thermoplastic filaments. Tensile tests and micrographs of the fracture surfaces prove the mechanical isotropy of the solid epoxy formulation. In addition, the material formulation is modified with single-walled carbon nanotubes to add electrical conductivity and allow functional 3D printing. Due to the high aspect ratio of the nanoparticles, a significantly lower filler content is necessary compared to the commercial materials. However, an electrical anisotropy is still observed as the material remains in a solid state during post-curing to retain its shape which limits the mobility of the nanoparticles and suppresses the agglomeration needed for conductive network formation after thorough dispersion. Proof of concept studies show that the functionalized material can be used in temperature and strain sensing applications.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · 3D Printing in Biomedical Research · Nanotechnology research and applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (74)
Show source-provided references
1. Gebhardt · 2013
2. Gibson · 2015
3. Sculpteo · 2018
4. 3D printing of polymer matrix composites: A review and prospective10.1016/j.compositesb.2016.11.034 ↗
5. Mechanical characterization of 3D-printed polymers
6. Modeling of bond formation between polymer filaments in the fused deposition modeling process10.1016/S1526-6125(04)70071-7 ↗
7. Bond and part strength in fused deposition modeling10.1108/RPJ-03-2016-0050 ↗
8. Design for fused filament fabrication additive manufacturing
9. Carbon nanotube reinforced fused deposition modeling using microwave irradiation
10. Increased fracture toughness of additively manufactured amorphous thermoplastics via thermal annealing10.1016/j.polymer.2018.04.024 ↗
11. Increased fracture toughness of additively manufactured semi-crystalline thermoplastics via thermal annealing10.1016/j.polymer.2020.123091 ↗
12. On reducing anisotropy in 3D printed polymers via ionizing radiation10.1016/j.polymer.2014.07.054 ↗
13. Effects of cold plasma treatment on interlayer bonding strength in FFF process
14. An in-process laser localized pre-deposition heating approach to inter-layer bond strengthening in extrusion based polymer additive manufacturing10.1016/j.jmapro.2016.08.007 ↗
15. Interlayer thermal history modification for interface strength in fused filament fabricated parts10.1007/s40964-018-0063-1 ↗
16. Bimodal molecular weight samples improve the isotropy of 3D printed polymeric samples10.1016/j.polymer.2017.06.057 ↗
17. Ultraviolet-assisted direct-write fabrication of carbon nanotube/polymer nanocomposite microcoils10.1002/adma.200902192 ↗
18. Direct-write fabrication of freestanding nanocomposite strain sensors10.1088/0957-4484/23/8/085502 ↗
19. 3D-printing of lightweight cellular composites10.1002/adma.201401804 ↗
20. High-strength epoxy nanocomposites for 3D printing10.1016/j.compscitech.2018.03.008 ↗
21. 3D printing of high performance cyanate ester thermoset polymers10.1039/C7TA09466C ↗
22. Three-dimensional printing of multifunctional nanocomposites: manufacturing techniques and applications10.1002/adma.201506215 ↗
23. Diels–Alder reversible thermoset 3D printing: isotropic thermoset polymers via fused filament fabrication10.1002/adfm.201700318 ↗
24. 3D printing electronic components and circuits with conductive thermoplastic filament
25. 3D and 4D printing of polymer/CNTs-based conductive composites
26. 4D-printing—Fused deposition modeling printing and PolyJet printing with shape memory polymers composite10.1007/s12221-020-9882-z ↗
27. Investigation of the effects of multi-wall and single-wall carbon nanotubes concentration on the properties of ABS nanocomposites
28. Development of a colored GFRP with antistatic properties
29. Carbon nanoparticles’ impact on processability and physical properties of epoxy resins—A comprehensive study covering rheological, electrical, thermo-mechanical, and fracture properties (mode I and II)10.3390/polym11020231 ↗
30. Fundamental aspects of nano-reinforced composites10.1016/j.compscitech.2005.01.014 ↗
31. Carbon nanotube-reinforced epoxy-composites: enhanced stiffness and fracture toughness at low nanotube content10.1016/j.compscitech.2004.04.002 ↗
32. 3D printing of CNT- and graphene-based conductive polymer nanocomposites by fused deposition modeling10.1016/j.apmt.2017.04.003 ↗
33. 3D printed highly elastic strain sensors of multiwalled carbon nanotube/thermoplastic polyurethane nanocomposites10.1016/j.matdes.2017.06.011 ↗
34. 3D printing of multiaxial force sensors using carbon nanotube (CNT)/thermoplastic polyurethane (TPU) filaments10.1016/j.sna.2017.07.020 ↗
35. Morphological influence of carbon nanofillers on the piezoresistive response of carbon nanoparticle/epoxy composites under mechanical load10.1016/j.eurpolymj.2016.10.027 ↗
36. Carbon nanotubes and carbon nanotube structures used for temperature measurement10.3390/s19112464 ↗
37. Combined electrical and rheological properties of shear induced multiwall carbon nanotube agglomerates in epoxy suspensions10.1016/j.eurpolymj.2011.07.022 ↗
38. Frequency or amplitude?–Rheo-electrical characterization of carbon nanoparticle filled epoxy systems10.3390/polym10090999 ↗
39. Tailoring the electrical properties of MWCNT/epoxy composites controlling processing conditions10.1016/j.compositesa.2012.04.002 ↗
40. Smart dispersion: Validation of OCT and impedance spectroscopy as solutions for in-situ dispersion analysis of CNP/EP-composites
41. In-line monitoring of carbon nanoparticle epoxy dispersion processes10.1007/s11740-019-00884-5 ↗
42. Curing of dicyandiamide epoxy resins accelerated with substituted ureas10.1002/(SICI)1097-4628(19980919)69:12<2487::AID-APP20>3.0.CO;2-T ↗
43. Curing behavior of dicyandiamide/epoxy resin system using different accelerators10.1007/s13726-013-0158-y ↗
44. KAUTSCHUK-GROUP · 2020
45. 3DXTECH · 2021
46. Protoplant Inc. · 2018
47. 3DXTECH · 2017
48. Schröder · 2018
49. Mezger · 2014
50. German Institut for Standardization · 2012
51. German Institut for Standardization · 2012
52. Piezoresistive response of epoxy composites with carbon nanoparticles under tensile load10.1103/PhysRevB.80.245437 ↗
53. Percolation in carbon black filled epoxy resin10.1002/masy.19961040122 ↗
54. Agglomeration and electrical percolation behavior of carbon black dispersed in epoxy resin10.1002/(SICI)1097-4628(19970328)63:13<1741::AID-APP5>3.0.CO;2-G ↗
55. Ultra-low electrical percolation threshold in carbon-nanotube-epoxy composites10.1016/S0032-3861(03)00539-1 ↗
56. Analyzing the network formation and curing kinetics of epoxy resins by in situ near-infrared measurements with variable heating rates10.1016/j.tca.2015.08.008 ↗
57. Hexion Inc. · 2017
58. OCSiAl Europe S.a.r.l · 2019
59. Ellis · 1993
60. Petrie · 2006
61. Ehrenstein · 2011
62. Fractography of unfilled and particulate-filled epoxy resins10.1007/BF01115700 ↗
63. Hayes · 2015
64. OCSiAl Europe S.a.r.l · 2020
65. Evaluation and identification of electrical and thermal conduction mechanisms in carbon nanotube/epoxy composites10.1016/j.polymer.2006.01.029 ↗
66. A review and analysis of electrical percolation in carbon nanotube polymer composites10.1016/j.compscitech.2008.06.018 ↗
67. Influence of carbon nanoparticle modification on the mechanical and electrical properties of epoxy in small volumes10.1016/j.jcis.2017.07.085 ↗
68. Two percolation thresholds in carbon nanotube epoxy composites10.1016/j.compscitech.2006.02.037 ↗
69. Controlled growth of semiconducting and metallic single-wall carbon nanotubes10.1021/jacs.6b00838 ↗
70. A comparative study of field emission from semiconducting and metallic single-walled carbon nanotube planar emitters10.1002/pssb.201700268 ↗
71. Simple and scalable gel-based separation of metallic and semiconducting carbon nanotubes10.1021/nl8034866 ↗
72. Generalized formula for the electric tunnel effect between similar electrodes separated by a thin insulating film10.1063/1.1702682 ↗
73. Generalized thermal J-V characteristic for the electric tunnel effect10.1063/1.1713820 ↗
74. Determinant role of tunneling resistance in electrical conductivity of polymer composites reinforced by well dispersed carbon nanotubes10.1063/1.3499628 ↗