Characterizing surface finish and fatigue behavior in binder-jet 3D-printed nickel-based superalloy 625
Source abstract
Abstract
Abstract In this study, the fatigue properties of binder-jet 3D-printed nickel-base superalloy 625 were evaluated. Standard fatigue specimens were printed and sintered, then half of the samples were mechanically ground, while the other half were left in their as-sintered state. They were then characterized using micro-computed x-ray tomography, metallographic sample examination, and optical and stylus profilometry for surface topography. The micro-computed tomography observations showed that density of the as-printed sample was ∼50%, while the sintered sample neared full densification (98.9 ± 0.3%) upon sintering at 1285 °C for 4 h in a vacuum atmosphere. The metallographic examination showed equiaxed grains. The roughness of the as-sintered samples was significant with an RMS roughness of Rq = 1.39 ± 0.20 μm as measured over a line-scan of 5 mm, but this was reduced to Rq = 0.47 ± 0.02 μm after mechanical grinding. All samples were tested to failure in fatigue, under fully-reversed tension-compression conditions. While the as-sintered samples showed poor fatigue properties compared to prior reports on cast and milled parts, the ground samples showed superior performance. Scanning electron microscopy observation was conducted on the fractured surfaces and showed that the samples underwent transgranular crack initiation, followed by intergranular crack growth and final failure. In the mechanically ground sample, hardness increased nearly two-fold up to 75 μm beneath the sample’s surface, and X-ray diffraction indicated an in-plane compressive stress, grain refinement, and micro-strain on the mechanically ground sample. The reduced roughness, surface hardening, and compressive stress resulted in increased fatigue life of the binder-jetted alloy 625.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (55)
Show source-provided references
1. Effect of solutionizing and aging on the microstructure and mechanical properties of powder bed binder jet printed nickel-based superalloy 62510.1016/j.matdes.2016.08.083 ↗
2. Microstructural evolution and magnetic properties of binder jet additive manufactured Ni-Mn-Ga magnetic shape memory alloy foam10.1016/j.actamat.2017.04.010 ↗
3. Microstructure characteristics of inconel 625 superalloy manufactured by selective laser melting10.1016/j.jmst.2014.09.020 ↗
4. Fatigue and fracture toughness characteristics of laser rapid manufactured inconel 625 structures10.1016/j.msea.2010.08.034 ↗
5. Comparison of microstructures and properties for a Ni-Base superalloy (alloy 625) fabricated by electron beam melting
6. Properties of inconel 625 mesh structures grown by electron beam additive manufacturing10.1016/j.msea.2014.07.051 ↗
7. Binder-jet printing of fine stainless steel powder with varied final density10.1007/s11837-016-2177-6 ↗
8. Fatigue behavior of laser consolidated IN-625 at room and elevated temperatures10.1016/j.msea.2009.03.056 ↗
9. Powder bed binder jet printed alloy 625: densification, microstructure and mechanical properties10.1016/j.matdes.2016.06.067 ↗
10. Data on the densification during sintering of binder jet printed samples made from water- and gas-atomized alloy 625 powders10.1016/j.dib.2016.11.078 ↗
11. Powder bed binder jet 3D printing of inconel 718: densification, microstructural evolution and challenges
12. Binder jetting: a novel NdFeB bonded magnet fabrication process10.1007/s11837-016-1883-4 ↗
13. Microstructural evolution and mechanical properties of differently heat-treated binder jet printed samples from gas- and water-atomized alloy 625 powders10.1016/j.actamat.2016.11.021 ↗
14. A comparative study of oxide scales grown on stainless steel and nickel-based superalloys in ultra-high temperature supercritical water at 800 °C10.1016/j.corsci.2016.02.004 ↗
15. Laser aided direct metal deposition of inconel 625 superalloy: microstructural evolution and thermal stability10.1016/j.msea.2009.01.009 ↗
16. Seawater corrosion behavior of laser surface modified inconel 625 alloy10.1016/0921-5093(95)10013-X ↗
17. Study of the pitting corrosion at welding joints of inconel 625 alloy under high temperature and high H2S2 partial pressure10.20964/2017.10.46 ↗
18. The effect of explosive welding parameters on metallurgical and mechanical interfacial features of inconel 625/plain carbon steel bimetal plate10.1016/j.msea.2012.07.012 ↗
19. Effect of niobium on marine crevice corrosion resistance of inconel alloy 625
20. Tribocorrosion behaviors of inconel 625 alloy sliding against 316 steel in seawater10.1080/10402004.2011.571362 ↗
21. Laser cladding of aerospace materials10.1016/S0924-0136(01)01121-9 ↗
22. Effect of severe shot peening and ultra-low temperature plasma nitriding on Ti-6Al-4V alloy10.1016/j.vacuum.2018.01.027 ↗
23. Influence of waterjet peening and smoothing on the material surface and properties of stainless steel 30410.1016/j.surfcoat.2014.07.013 ↗
24. Surface severe plastic deformation of AISI 304 via conventional shot peening, severe shot peening and repeening10.1016/j.apsusc.2015.05.093 ↗
25. Uniformity of residual stress distribution on the surface of S30432 austenitic stainless steel by different shot peening processes10.1016/j.matlet.2012.08.147 ↗
26. Microstructure evolution and strengthening mechanisms of pure titanium with nano-structured surface obtained by high energy shot peening10.1016/j.vacuum.2016.01.001 ↗
27. Evaluation of the residual stress and microstructure character in SAF 2507 duplex stainless steel after multiple shot peening process10.1016/j.surfcoat.2018.03.012 ↗
28. Fatigue strength of inconel 625 plate and weldments used in the DIII-D configuration vacuum vessel10.1016/0022-3115(85)90165-5 ↗
29. High temperature low cycle fatigue properties of alloy 62510.1016/j.msea.2015.10.023 ↗
30. Fatigue resistance of alloy 625 sheet
31. Fatigue performance evaluation of selective laser melted Ti-6Al-4V10.1016/j.msea.2014.01.041 ↗
32. Influence of surface pre-treatments on the high-cycle fatigue behavior of Ti – 6Al – 4V – from anodizing to laser-assisted techniques10.1016/j.ijfatigue.2016.06.010 ↗
33. Fatigue life of additively manufactured Ti-6Al-4V in the very high cycle fatigue regime10.1016/j.ijfatigue.2016.05.018 ↗
34. Metal additive manufacturing: a review of mechanical properties10.1146/annurev-matsci-070115-032024 ↗
35. Study of selective laser melting (SLM) inconel 718 part surface improvement by electrochemical polishing10.1016/j.matdes.2016.11.103 ↗
36. An experimental investigation into the dimensional error of powder-binder three-dimensional printing10.1007/s00170-015-7482-7 ↗
37. Effect of layer thickness and orientation on mechanical behavior of binder jet stainless steel 420 + bronze parts10.1016/j.promfg.2015.09.016 ↗
38. Binder-jetting 3D printing and alloy development of new biodegradable Fe-Mn-Ca/Mg alloys10.1016/j.actbio.2016.08.032 ↗
39. Effect of powders and binders on material properties and molding parameters in iron and stainless steel powder injection molding process10.1016/j.powtec.2009.03.010 ↗
40. Comparison of characterization methods for differently atomized nickel-based alloy 625 powders10.1016/j.powtec.2018.04.014 ↗
41. Influence of the WEDM process on the fatigue behavior of inconel 71810.1016/j.ijfatigue.2016.07.011 ↗
42. Avery · JOM · 2018
43. Effect of stress ratio and v notch shape on fatigue life in steel beam
44. Campbell · 2012
45. 2008 · 243
46. Quantitative characterization of surface topography using spectral analysis10.1088/2051-672X/aa51f8 ↗
47. Combining TEM, AFM, and profilometry for quantitative topography characterization across all scales10.1021/acsami.8b09899 ↗
48. Fatigue limit of Ti6Al4V alloy produced by selective laser sintering10.1016/j.prostr.2016.06.394 ↗
49. Critical assessment of the fatigue performance of additively manufactured Ti-6Al-4V and perspective for future research10.1016/j.ijfatigue.2015.12.003 ↗
50. Effect of surface roughness on fatigue performance of additive manufactured Ti–6Al–4V10.1179/1743284715Y.0000000053 ↗
51. On the mechanical behaviour of titanium alloy Ti-6Al-4V manufactured by selective laser melting: fatigue resistance and crack growth performance10.1016/j.ijfatigue.2012.11.011 ↗
52. Bending fatigue life characterisation of direct metal laser sintering nickel alloy 718, fatigue fract10.1111/ffe.12286 ↗
53. Low cycle fatigue behavior of direct metal laser sintered inconel alloy10.1016/j.ijfatigue.2016.08.019 ↗
54. An examination of the effects from surface texture on the strength of fiber reinforced plastics10.1177/002199839903300201 ↗
55. Modelling the influence of machined surface roughness on the fatigue life of aluminium alloy10.1016/j.ijfatigue.2008.06.003 ↗