Polycarbonate composites for material extrusion-based additive manufacturing of thermally conductive objects
Source abstract
Abstract
Enhanced thermally conductive polymer composites can be used in many engineering applications where either the physicochemical properties of plastics or the processing properties of plastics are required. Rapid prototyping is currently being addressed for a number of applications that require good heat transfer properties. Such applications include various types of heat exchangers containing coolant/heating fluid as well as passive heat sinks for standard heat removal from various types of heat-generating products. The present work is focused on the research of thermally conductive composites for printing such structures using additive manufacturing (AM), namely material extrusion. In this study, a number of parameters of the composites were investigated that affect the final properties of the printed structures; these include the TC (Thermal Conductivity), mechanical properties, and printability of the composites, depending on the composition, but also the printing direction. The composites studied were made up of a matrix of PC (Polycarbonate) and a mixture of different thermally conductive fillers, specifically, h-BN (Hexagonal Boron Nitride), EG (Expanded Graphite), PCFs (Pitch-based Carbon Fibers) and Al (Aluminum Particles). Different types of thermally conductive composites were studied, from binary to ternary combinations of fillers. One of the best-performing composites was achieved for the combination of all four types of filler, where thermal conductivity along the printing direction was achieved for the PC matrix with 30 wt% of the mixture of all fillers. Up to 1.56 W m−1 K−1 was achieved, which is 5-fold higher than for neat PC. Although these composites have approximately half the tensile strength only, the hardness is similar to that of the neat PC. The behavior of fillers was observed by SEM analysis. Al, EG, and PCFs behave predictably. Unusual behavior was observed in the case of PC only with h-BN, where the filler migration from the matrix to the voids between the non-fused printing paths occurred, likely caused by a larger amount of dispersion component of the overall surface energy of h-BN. Such phenomena could be used in the optimized form in the future so that segregated thermally conductive structures could be created using material extrusion-based AM and allow even higher thermal conductivity of final structures.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Thermal properties of materials · Additive Manufacturing Materials and Processes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. P. Roudný, T. Syrový, Thermal conductive composites for FDM 3D printing: A review, opportunities and obstacles, future directions, Journal of manufacturing processes 83 667–677. https://doi.org/10.1016/j.jmapro.2022.09.026.10.1016/j.jmapro.2022.09.026 ↗
2. Progress of polymer-based thermally conductive materials by fused filament fabrication: a comprehensive review10.3390/polym14204297 ↗
3. X. Huang, P. Jiang, T. Tanaka, A review of dielectric polymer composites with high thermal conductivity, IEEE Electrical Insulation Magazine 27(4) 8–16. https://doi.org/10.1109/MEI.2011.5954064.10.1109/MEI.2011.5954064 ↗
4. J. Liu, W. Li, Y. Guo, H. Zhang, Z. Zhang, Improved thermal conductivity of thermoplastic polyurethane via aligned boron nitride platelets assisted by 3D printing, Composites. Part A, Applied science and manufacturing 120 140–146. https://doi.org/10.1016/j.compositesa.2019.02.026.10.1016/j.compositesa.2019.02.026 ↗
5. Improvement of the thermal conductivity and mechanical properties of 3D-printed polyurethane composites by incorporating hydroxylated boron nitride functional fillers10.3390/ma16010356 ↗
6. J. Ji, S.W. Chiang, M. Liu, X. Liang, J. Li, L. Gan, Y. He, B. Li, F. Kang, H. Du, Enhanced thermal conductivity of alumina and carbon fibre filled composites by 3-D printing, Thermochimica acta 690. https://doi.org/10.1016/j.tca.2020.178649.10.1016/j.tca.2020.178649 ↗
7. A.A. Stepashkin, D.I. Chukov, F.S. Senatov, A.I. Salimon, A.M. Korsunsky, S.D. Kaloshkin, 3D-printed PEEK-carbon fiber (CF) composites: Structure and thermal properties, Composites science and technology 164 319–326. https://doi.org/10.1016/j.compscitech.2018.05.032.10.1016/j.compscitech.2018.05.032 ↗
8. Y. Jia, H. He, Y. Geng, B. Huang, X. Peng, High through-plane thermal conductivity of polymer based product with vertical alignment of graphite flakes achieved via 3D printing, Composites science and technology 145 55–61. https://doi.org/10.1016/j.compscitech.2017.03.035.10.1016/j.compscitech.2017.03.035 ↗
9. Thermal properties of 3-D printed polylactic acid-metal composites10.1007/s40964-017-0019-x ↗
10. H. Zhou, M. Ran, Y. Li, Z. Yin, Y. Tang, W. Zhang, W. Zheng, J. Liu, Improvement of thermal conductivity of diamond/Al composites by optimization of liquid-solid separation process, Journal of materials processing technology 297. https://doi.org/10.1016/j.jmatprotec.2021.117267.10.1016/j.jmatprotec.2021.117267 ↗
11. Incropera · 2007
12. Y.-M. Chen, J.-M. Ting, Ultra high thermal conductivity polymer composites, Carbon (New York) 40(3) 359–362. https://doi.org/10.1016/S0008–6223(01)00112–9.10.1016/S0008-6223(01)00112-9 ↗
13. S.Y. Pak, H.M. Kim, S.Y. Kim, J.R. Youn, Synergistic improvement of thermal conductivity of thermoplastic composites with mixed boron nitride and multi-walled carbon nanotube fillers, Carbon (New York) 50(13) 4830–4838. https://doi.org/10.1016/j.carbon.2012.06.009.10.1016/j.carbon.2012.06.009 ↗
14. H.S. Kim, J.H. Kim, Ch-M. Yang, S.Y. Kim, Synergistic enhancement of thermal conductivity in composites filled with expanded graphite and multi-walled carbon nanotube fillers via melt-compounding based on polymerizable low-viscosity oligomer matrix, Journal of alloys and compounds 690 274–280. https://doi.org/10.1016/j.jallcom.2016.08.141.10.1016/j.jallcom.2016.08.141 ↗
15. Y.J. Noh, S.Y. Kim, Synergistic improvement of thermal conductivity in polymer composites filled with pitch based carbon fiber and graphene nanoplatelets, Polymer testing 45 132–138. https://doi.org/10.1016/j.polymertesting.2015.06.003.10.1016/j.polymertesting.2015.06.003 ↗
16. Effect of filler shape on the thermal conductivity of thermal functional composites
17. N. Mehra, L. Mu, T. Ji, X. Yang, J. Kong, J. Gu, J. Zhu, Thermal transport in polymeric materials and across composite interfaces, Applied materials today 12 92–130. https://doi.org/10.1016/j.apmt.2018.04.004.10.1016/j.apmt.2018.04.004 ↗
18. Synergistic effect of aligned graphene nanosheets in graphene foam for high‐performance thermally conductive composites10.1002/adma.201900199 ↗
19. Design and preparation of a unique segregated double network with excellent thermal conductive property10.1021/acsami.6b16586 ↗
20. Thermally conductive graphene-polymer composites: size, percolation, and synergy effects10.1021/cm504550e ↗
21. Stress controllability in thermal and electrical conductivity of 3D elastic graphene‐crosslinked carbon nanotube sponge/polyimide nanocomposite
22. Enhanced thermal conductivity and isotropy of polymer composites by fabricating 3D network structure from carbon‐based materials10.1002/app.49781 ↗
23. Enhancing thermal conductivity and balancing mechanical properties of 3D-printed iPP/HDPE-based dielectric composites via the introduction of hybrid fillers and tailored crystalline structure10.1080/17452759.2023.2230215 ↗
24. D.D.L. Chung, Materials for thermal conduction, Applied thermal engineering 21(16) 1593–1605. https://doi.org/10.1016/S1359–4311(01)00042–4.10.1016/S1359-4311(01)00042-4 ↗
25. Highly oriented carbon fiber–polymer composites via additive manufacturing10.1016/j.compscitech.2014.10.009 ↗
26. J.J. Fallon, S. Mcknight, M. Bortner, Highly loaded fiber filled polymers for material extrusion: A review of current understanding, Additive manufacturing 30. https://doi.org/10.1016/j.addma.2019.100810.10.1016/j.addma.2019.100810 ↗
27. H. Pang, L. Xu, D.-X. Yan, Z.-M. Li, Conductive polymer composites with segregated structures, Progress in polymer science 39(11) 1908–1933. https://doi.org/10.1016/j.progpolymsci.2014.07.007.10.1016/j.progpolymsci.2014.07.007 ↗
28. Heat transfer, thermophysical and rheological behavior of highly stable few-layers of h-BN nanosheets/EG-based nanofluid
29. Y. Kimura, T. Wakabayashi, K. Okada, T. Wada, H. Nishikawa, Boron nitride as a lubricant additive, Wear 232(2) 199–206. https://doi.org/10.1016/S0043–1648(99)00146–5.10.1016/S0043-1648(99)00146-5 ↗
30. V. Nienhaus, K. Smith, D. Spiehl, E. Dörsam, Investigations on nozzle geometry in fused filament fabrication, Additive manufacturing 28 711–718. https://doi.org/10.1016/j.addma.2019.06.019.10.1016/j.addma.2019.06.019 ↗
31. S. Min, J. Blumm, A. Lindemann, A new laser flash system for measurement of the thermophysical properties, Thermochimica acta 455(1–2) 46–49. https://doi.org/10.1016/j.tca.2006.11.026.10.1016/j.tca.2006.11.026 ↗
32. Computing the bond strength of 3D printed polylactic acid scaffolds in mode I and II using experimental tests, finite element method and cohesive zone modeling10.1007/s00170-021-08124-w ↗
33. The effect of surface energy of boron nitride on polymer processability10.1002/pen.20151 ↗
34. Studies on modification of surface properties in polycarbonate (PC) film induced by DC glow discharge plasma10.1155/2011/426057 ↗
35. Surface modification of polycarbonate (bisphenol A) by low pressure rf plasma
36. Variations in aluminum particle surface energy and reactivity induced by annealing and quenching10.1016/j.apsusc.2021.152185 ↗
37. Evaluation of the surface energy of dispersed aluminium oxide using owens-wendt theory10.15587/2312-8372.2020.200756 ↗