High temperature fracture toughness of TZM alloys with different kinds of grain boundary particles
Source abstract
Abstract
Abstract The elastic-plastic fracture toughness JIC of two titanium-zirconium-molybdenum (TZM) alloys with different kinds of grain boundary particles was estimated at elevated temperatures using the convenient JIC test method with a suitable depth of side-groove for determining the JIC at the maximum load point. It was found that the convenient JIC test method can be successfully applied to evaluate high temperature fracture toughness at least up to 1200 °C. The JIC values at temperatures ranged from 800 °C to 1200 °C were almost constant regardless of temperature, while the JIC values of the TZM with carbide particles were higher than those of the TZM with oxide particles. The TZM with different forging rates showed similar JIC values, which suggested the effect of forging rate would be not significant at high temperatures.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (16)
Show source-provided references
1. Walser · 2007 · July
2. The 700°C tensile behavior of Mo-0.5 Ti-0.08 Zr-0.025 C (TZM) extruded bar measured transverse and parallel to the billet extrusion axis10.1016/S0263-4368(98)00012-2 ↗
3. Improvement in recrystallization temperature and mechanical properties of a commercial TZM alloy through microstructure control by multi-step internal nitriding10.2320/matertrans.46.2129 ↗
4. Tensile properties and fracture mode of a wrought ODS molybdenum sheet following fast neutron irradiation at temperatures ranging from 300°C to 1000°C10.1016/j.jnucmat.2005.06.020 ↗
5. Hardening mechanisms and recrystallization behaviour of several molybdenum alloys10.1016/j.ijrmhm.2005.10.003 ↗
6. Evolution of microstructure during hot deformation of the PM molybdenum alloy TZM
7. Change of mechanical property and fracture mode of molybdenum by carbon addition10.2320/matertrans.M2009377 ↗
8. La2O3 effects on TZM alloy recovery, recrystallization and mechanical properties10.1016/j.msea.2015.03.114 ↗
9. Effect of rhenium addition on fracture-toughness of tungsten at elevated temperatures10.1007/BF00356341 ↗
10. The mechanical properties and fracture mechanisms of wrought low carbon arc cast (LCAC), molybdenum–0.5pct titanium–0.1pct zirconium (TZM), and oxide dispersion strengthened (ODS) molybdenum flat products10.1016/j.msea.2005.11.030 ↗
11. A simple JIC test method using a side-grooved Charpy-size specimen
12. Microstructure, high temperature strength and CO-gas emission of liquid-phase sintered and forged low oxygen TiC-ZrC-Mo alloy10.2472/jsms.55.558 ↗
13. Development of Mo alloys with improved resistance to embrittlement by recrystallization and irradiation10.1016/S0022-3115(96)00333-9 ↗
14. Fracture toughness evaluation of hardmetals: influence of testing procedure10.1016/S0263-4368(00)00044-5 ↗
15. A comparison of the microstructure and high temperature tensile properties of a novel P/M Mo-Hf-Zr-Ta-C alloy and TZM
16. Measuring the fracture toughness of molybdenum-0.5 pct titanium-0.1 pct zirconium and oxide dispersion—strengthened molybdenum alloys using standard and subsized bend specimens10.1007/s11661-002-0242-y ↗