journal article·2024-01

Effect of sintering aid combined vacuum infiltration on the properties of Al2O3-based ceramics via binder jetting

Zhiyuan Yang, Li Yang, Panlong Wang, Ziwei Peng, Yanqing Niu, Wenming Jiang, Zitian Fan

Publisher page

Abstract

Binder Jetting (BJ) technology enables cost-effective and efficient fabrication of complex Al2O3-based ceramic components. However, in the process of manufacturing Al2O3-based ceramics using BJ, issues such as high sintering temperatures and relatively low sintered strength and relative density are encountered. In this study, we investigated the MnO2 sintering aid in combination with TiO2 sol-gel vacuum infiltration to introduce a MnO-TiO2-Al2O3 ternary sintering system, which could reduce the sintering temperature and enhance the strength and relative density of Al2O3-based ceramics. Through single-factor and response surface experiments, the effects of MnO2 addition, green body sintering temperature, infiltration time, and infiltration vacuum level on the properties and reinforcement mechanism of BJ Al2O3-based ceramics were studied. The research results revealed that with 10% MnO2 addition, a sintering temperature of 1450 °C, infiltration time of 60 s, and infiltration vacuum level of 24 KPa, the bending strength and sintered relative density of Al2O3-based ceramics reached 113.79 MPa and 78.13%, respectively. The bending strength was 48 times higher than that of the Al2O3 ceramic samples without sintering aid composite infiltration treatment, and the sintered relative density was improved by 41.85%.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Innovations in Concrete and Construction Materials · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. A review on laser deposition-additive manufacturing of ceramics and ceramic reinforced metal matrix composites10.1016/j.ceramint.2018.08.083 ↗
2. 3D printing of fine alumina powders by binder jetting10.1016/j.jeurceramsoc.2021.04.006 ↗
3. Postprocessing study for the controllable structures of ceramic green parts realized by a flexible binder jetting printing (BJP) solution10.1155/2020/3865752 ↗
4. Progress in additive manufacturing on new materials: a review10.1016/j.jmst.2018.09.002 ↗
5. Additive manufacturing (3D printing): a review of materials, methods, applications and challenges10.1016/j.compositesb.2018.02.012 ↗
6. Application of stereolithography based 3D printing technology in investment casting10.3390/mi11100946 ↗
7. High-performance ceramic parts with complex shape prepared by selective laser sintering: a review10.1080/17436753.2017.1379586 ↗
8. Performance characteristics of collapsible CaO-SiO 2 based ceramic core material via layered extrusion forming10.1016/j.ceramint.2019.01.068 ↗
9. Effect of silica sol on performance and surface precision of alumina ceramic shell prepared by binder jetting10.1016/j.ceramint.2022.05.021 ↗
10. Additive manufacturing of ceramic-based materials10.1002/adem.201400097 ↗
11. Preparation of high-porosity Al2O3 ceramic foams via selective laser sintering of Al2O3 poly-hollow microspheres10.1016/j.ceramint.2019.10.144 ↗
12. 3D printing of highly-loaded slurries via layered extrusion forming: parameters optimization and control
13. Reaction-bonding of aluminum oxide processed by binder jetting10.1016/j.jmapro.2019.04.008 ↗
14. Ceramic binder jetting additive manufacturing: a literature review on density10.1115/1.4046248 ↗
15. Tailoring α-alumina powder morphology through spray drying for cold consolidation by binder jetting
16. W. Du, X. Ren, Y. Chen, C. Ma, M. Radovic, Z. Pei, Model guided mixing of ceramic powders with graded particle sizes in binder jetting additive manufacturing, ASME 2018 13th International Manufacturing Science and Engineering Conference, MSEC 2018. 1 (2018) 1–9. https://doi.org/10.1115/MSEC2018–6651.10.1115/MSEC2018-6651 ↗
17. Characterization of ceramic components fabricated using binder jetting additive manufacturing technology10.1016/j.ceramint.2016.03.079 ↗
18. 3D printing high density ceramics using binder jetting with nanoparticle densifiers10.1016/j.matdes.2018.06.009 ↗
19. Additive manufacturing of thin alumina ceramic cores using binder-jetting
20. 3D printing of CaO-based ceramic core using nanozirconia suspension as a binder10.1016/j.jeurceramsoc.2017.06.050 ↗
21. Fabrication of ceramic bone scaffolds by solvent jetting 3D printing and sintering: towards load-bearing applications
22. Improved green and sintered density of alumina parts fabricated by binder jetting and subsequent slurry infiltration10.1007/s40964-021-00222-1 ↗
23. Post-infiltration to improve the density of binder jetting ceramic parts10.1016/j.jeurceramsoc.2022.08.005 ↗
24. Ceramic binder jetting additive manufacturing: effects of granulation on properties of feedstock powder and printed and sintered parts
25. Binder jetting yttria stabilised zirconia ceramic with inorganic colloid as a binder10.1080/17436753.2019.1666593 ↗
26. Sintering of alumina at temperatures of 1400℃ and below10.1111/j.1151-2916.1957.tb12589.x ↗
27. Densification of alumina at 1250 °C with MnO2 and TiO2 additives10.1016/0272-8842(95)96207-6 ↗
28. Dopant diffusion at the interface of TiO2-MnO-doped alumina/alumina layers in sintered laminates10.1002/ces2.10090 ↗
29. Manganese dioxide structural effects on its thermal decomposition10.1016/j.mseb.2011.06.007 ↗
30. Phase equilibrium relationships in the system Al2O3-TiO2-MnO, relevant to the low-temperature sintering of alumina10.1016/0955-2219(96)00024-6 ↗
31. Multi-objective optimization of iron ore induration process using optimal neural networks10.1080/10426914.2019.1643476 ↗
32. Process optimization of porous Al2O3 filter via layered extrusion forming10.1080/10426914.2022.2032143 ↗
33. Preparation and interface investigation of Fe/Al2O3P composite activated by Ni and Ti10.1002/adem.201600302 ↗