journal article·2026-06-23Open access

A Review of Wind Turbine Reliability and Long-Term Performance: Failure Mechanisms, Monitoring Strategies, and AI-Enabled Predictive Maintenance

Sajid Ali, Muhammad Waleed, Daeyong Lee

Applied Sciences· Volume 16· Issue 13

Abstract

Wind turbines are increasingly deployed at larger scales and in harsher operating environments, leading to greater structural complexity, stronger load variability, and higher maintenance demands across both drivetrain and structural components. Reported field data indicate that gearboxes and bearings account for approximately 30–40% of total turbine downtime, while blade-related failures contribute roughly 20–25% of reported failure events, primarily through fatigue, delamination, leading-edge erosion, and lightning-induced defects. In parallel, large-scale and offshore turbines show increasing susceptibility to tower fatigue cracking, corrosion-assisted degradation, and flange joint bolt-preload loss under cyclic and environmental loading. This review provides a comprehensive applied-engineering synthesis of failure mechanisms, reliability challenges, and monitoring strategies for major wind turbine components, including gearboxes, bearings, blades, towers, and flange joints. A wide range of condition monitoring, structural health monitoring (SHM), and prognostics and health management (PHM) approaches is critically examined, including vibration analysis, acoustic emission, ultrasonic inspection, infrared thermography, impedance-based sensing, electromagnetic methods, machine vision, SCADA-based diagnostics, and artificial-intelligence-assisted fault classification. The review compares these techniques in terms of detectable damage types, spatial coverage, sensitivity, deployment practicality, and limitations under real operating conditions. In addition, statistical reliability methods and data-driven models are discussed to interpret failure trends and uncertainty. Recent AI-based studies have reported fault classification accuracies exceeding 90% under controlled or semi-controlled conditions; however, their field reliability remains constrained by data imbalance, domain shift, limited labeled failure datasets, model interpretability, and insufficient validation under realistic turbine operating environments. The main contribution of this review is an integrated applied synthesis that connects drivetrain and structural failure mechanisms with measurable monitoring indicators, diagnostic technologies, AI-enabled PHM limitations, and predictive-maintenance decision needs. The paper provides practical guidance for monitoring design, early fault detection, predictive maintenance, and long-term reliability improvement in next-generation wind turbine systems.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Machine Fault Diagnosis Techniques · Structural Health Monitoring Techniques · Gear and Bearing Dynamics Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Energy Innovation Research Center for Wind Turbine Support Structures, Kunsan National University, 558 Daehak-ro, Gunsan-si 54150, Jeonbuk-do, Republic of Korea

Department of Wind Energy, The Graduate School of Kunsan National University, 558 Daehak-ro, Gunsan-si 54150, Jeonbuk-do, Republic of Korea

Funding

Korea Institute of Energy Technology Evaluation and Planning · National Research Foundation of Korea

References (100+)

Show source-provided references
1. Verbruggen, T. (2003). Wind Turbine Operation & Maintenance Based on Condition Monitoring WT-Ω, Energy Research Centre of the Netherlands (ECN). Final Report.
2. Failure rate, repair time and unscheduled O&M cost analysis of offshore wind turbines10.1002/we.1887 ↗
3. Wind energy systems10.1109/JPROC.2017.2695485 ↗
4. Franko, J., Du, S., Kallweit, S., Duelberg, E., and Engemann, H. (2020). Design of a multi-robot system for wind turbine maintenance. Energies, 13.10.3390/en13102552 ↗
5. Offshore wind power generation technologies10.1109/JPROC.2012.2225591 ↗
6. A review on development of offshore wind energy conversion system10.1002/er.5751 ↗
7. Wind turbine reliability analysis10.1016/j.rser.2013.03.018 ↗
8. Wind turbine reliability data review and impacts on levelised cost of energy10.1002/we.2404 ↗
9. Hahn, B., Durstewitz, M., and Rohrig, K. (2007). Reliability of wind turbines. Wind Energy: Proceedings of the Euromech Colloquium, Springer.10.1007/978-3-540-33866-6_62 ↗
10. International Renewable Energy Agency (IRENA) (2012). Renewable Energy Technologies: Cost Analysis Series, Wind Power, International Renewable Energy Agency (IRENA).
11. Advanced logistics planning for offshore wind farm operation and maintenance activities10.1016/j.oceaneng.2015.04.040 ↗
12. Technical Aspects of Different Grid Connected Wind Energy Conversion System Configurations in Wind Farm10.35940/ijeat.A9888.109119 ↗
13. Wind turbine downtime and its importance for offshore deployment10.1002/we.421 ↗
14. Reliability of Wind Turbine Subassemblies10.1049/iet-rpg.2008.0060 ↗
15. Sheng, S. (2014). Gearbox Typical Failure Modes, Detection and Mitigation Methods.
16. Jin, X., Cheng, F., Peng, Y., Qiao, W., and Qu, L. (2016). A comparative study on vibration-and current-based approaches for drivetrain gearbox fault diagnosis. 2016 IEEE Industry Applications Society Annual Meeting, IEEE.10.1109/IAS.2016.7731964 ↗
17. Wind turbines lubricant gearbox degradation detection by means of a lossy mode resonance based optical fiber refractometer10.1007/s00542-015-2791-1 ↗
18. Future research directions for the wind turbine generator system10.1016/j.rser.2015.04.126 ↗
19. A survey on wind turbine condition monitoring and fault diagnosis-Part I: Components and subsystems10.1109/TIE.2015.2422112 ↗
20. Research and Markets (2014). Wind Turbine Gearbox and Direct-Drive Systems, 2014 Update—Global Market Size, Gearbox Refurbishments, Competitive Landscape and Key Country Analysis to 2020, Research and Markets. Technical Report 2974385.
21. Performance assessment of wind turbine gearboxes using in-service data: Current approaches and future trends10.1016/j.rser.2015.04.139 ↗
22. On the use of a single piezoelectric strain sensor for wind turbine planetary gearbox fault diagnosis10.1109/TIE.2015.2442216 ↗
23. An interval NLPV parity equations approach for fault detection and isolation of a wind farm
24. Sheng, S. (2013). Report on Wind Turbine Subsystem Reliability—A Survey of Various Databases (Presentation), No. NREL/PR-5000-59111.
25. A review of wind turbine bearing condition monitoring: State of the art and challenges10.1016/j.rser.2015.11.032 ↗
26. Fierro, T. (2025, December 28). Extending Bearing Life in Wind Turbine Mainshafts. Power Engineering, 23 August 2016. Available online: https://www.power-eng.com/coal/extending-bearing-life-in-wind-turbine-mainshafts/#gref.
27. The PRISMA 2020 statement: An updated guideline for reporting systematic reviews10.1136/bmj.n71 ↗
28. Energy efficiency tests in a full scale wind turbine gearbox10.1016/j.triboint.2016.05.001 ↗
29. A novel order tracking method for wind turbine planetary gearbox vibration analysis based on discrete spectrum correction technique10.1016/j.renene.2015.10.036 ↗
30. Monitoring wind turbine gearboxes10.1002/we.1521 ↗
31. A review on approaches for condition based maintenance in applications with induction machines located offshore10.4173/mic.2012.2.4 ↗
32. A review on wind turbines gearbox fault diagnosis methods10.21595/jve.2020.20178 ↗
33. Mathematical models used in gear dynamics-a review10.1016/S0022-460X(88)80365-1 ↗
34. Spur gear dynamic models including defects: A review10.1177/05831024030356002 ↗
35. Survey of nonlinear vibration of gear transmission systems10.1115/1.1555660 ↗
36. A review of planetary and epicyclic gear dynamics and vibrations research10.1115/1.4027812 ↗
37. Influences of planetary gear parameters on the dynamic characteristics-a review
38. Review on dynamics of cracked gear systems10.1016/j.engfailanal.2015.06.004 ↗
39. Dynamic modeling of gearbox faults: A review10.1016/j.ymssp.2017.05.024 ↗
40. Condition monitoring and fault diagnosis of planetary gearboxes: A review10.1016/j.measurement.2013.11.012 ↗
41. Application of the wavelet transform in machine condition monitoring and fault diagnostics: A review with bibliography10.1016/S0888-3270(03)00075-X ↗
42. Prognostics and health management: A review of vibration based bearing and gear health indicators10.1109/ACCESS.2017.2774261 ↗
43. A diagnostic signal selection scheme for planetary gearbox vibration monitoring under non-stationary operational conditions10.1088/1361-6501/aa543e ↗
44. Case study on the effectiveness of gear fault diagnosis technique for gear tooth defects under fluctuating speed10.1049/iet-rpg.2016.0639 ↗
45. A survey on wind turbine condition monitoring and fault diagnosis-Part II: Signals and signal processing methods10.1109/TIE.2015.2422394 ↗
46. A survey of health monitoring systems for wind turbines10.1016/j.rser.2015.07.110 ↗
47. A new wind turbine health condition monitoring method based on VMD-MPE and feature-based transfer learning10.1016/j.measurement.2019.106906 ↗
48. Elasha, F., Shanbr, S., Li, X., and Mba, D. (2019). Prognosis of a wind turbine gearbox bearing using supervised machine learning. Sensors, 19.10.3390/s19143092 ↗
49. A condition monitoring and fault isolation system for wind turbine based on SCADA data10.1109/TII.2021.3075239 ↗
50. Han, H., Yang, D., and Ni, X. (2021). Application of Sparse Representation in SCADA: Wind Turbine Fault Diagnosis Based on K-SVD. 2021 CAA Symposium on Fault Detection, Supervision, and Safety for Technical Processes (SAFEPROCESS), IEEE.10.1109/SAFEPROCESS52771.2021.9693662 ↗
51. Jiang, Z., Cao, Y., Hong, H., and Yang, Q. (2021). Fault detection and diagnosis of wind turbine gearbox based on acoustic analysis. 2021 International Conference on Power System Technology (POWERCON), IEEE.10.1109/POWERCON53785.2021.9697513 ↗
52. Application of acoustic emission technique to detection of rolling bearing failure
53. A comparison of some condition monitoring techniques for the detection of defect in induction motor ball bearings10.1016/j.ymssp.2005.08.005 ↗
54. A comparative study of the effectiveness of vibration and acoustic emission in diagnosing a defective bearing in a planetry gearbox10.1016/j.apacoust.2016.07.026 ↗
55. Data-driven wear monitoring for sliding bearings using acoustic emission signals and long short-term memory neural networks10.1016/j.wear.2021.203616 ↗
56. A comparative experimental study on the diagnostic and prognostic capabilities of acoustics emission, vibration and spectrometric oil analysis for spur gears10.1016/j.ymssp.2005.09.015 ↗
57. Condition monitoring of wind turbines: Techniques and methods10.1016/j.renene.2012.03.003 ↗
58. Machine fault signature analysis10.1155/2008/583982 ↗
59. Wind turbine planetary gearbox condition monitoring method based on wireless sensor and deep learning approach
60. Stator Electrical Fault Detection in DFIGs Using Wide-Band Analysis of the Embedded Signals from the Controllers10.1109/TEC.2020.3017443 ↗
61. Gong, X. (2012). Online Nonintrusive Condition Monitoring and Fault Detection for Wind Turbines. [Ph.D. Thesis, The University of Nebraska-Lincoln].
62. Critical wind turbine components prognostics: A comprehensive review10.1109/TIM.2020.3030165 ↗
63. Yang, T., Teng, J., Li, C., and Feng, Y. (2020). Wind turbine fault detection and diagnosis using LSTM neural network. 2020 39th Chinese Control Conference (CCC), IEEE.10.23919/CCC50068.2020.9188709 ↗
64. One-class classifier based fault detection in distribution systems with varying penetration levels of distributed energy resources10.1109/ACCESS.2020.3009385 ↗
65. An artificial neural network-based condition monitoring method for wind turbines, with application to the monitoring of the gearbox10.1002/we.2102 ↗
66. Condition monitoring of helical gears using automated selection of features and sensors10.1016/j.measurement.2016.07.011 ↗
67. Total process of fault diagnosis for wind turbine gearbox, from the perspective of combination with feature extraction and machine learning: A review10.1016/j.egyai.2023.100318 ↗
68. Application of the intrinsic time-scale decomposition method to fault diagnosis of wind turbine bearing10.1177/1077546311403185 ↗
69. Xin, W., Liu, Y., He, Y., and Su, B. (2012). Amplitude envelope analysis for feature extraction of direct-driven wind turbine bearing failure. Proceedings of the 10th World Congress on Intelligent Control and Automation, IEEE.10.1109/WCICA.2012.6358418 ↗
70. Pan, Z., Liang, S., Liu, Y., and Liang, P. (2015). Spectral correlation feature analysis for rolling bearing fault of wind turbine generator. International Conference on Renewable Power Generation (RPG 2015), IET.
71. Generalized transmissibility damage indicator with application to wind turbine component condition monitoring10.1109/TIE.2016.2580519 ↗
72. Bodla, M.K., Malik, S.M., Rasheed, M.T., Numan, M., Ali, M.Z., and Brima, J.B. (2016). Logistic regression and feature extraction based fault diagnosis of main bearing of wind turbines. 2016 IEEE 11th Conference on Industrial Electronics and Applications (ICIEA), IEEE.10.1109/ICIEA.2016.7603846 ↗
73. Wavelet-based multifractal analysis of large scale wind turbine main bearing10.1063/1.4773826 ↗
74. Purarjomandlangrudi, A., Nourbakhsh, G., Ghaemmaghami, H., and Tan, A. (2014). Application of anomaly technique in wind turbine bearing fault detection. IECON 2014-40th Annual Conference of the IEEE Industrial Electronics Society, IEEE.10.1109/IECON.2014.7048774 ↗
75. Wavelet energy transmissibility function and its application to wind turbine bearing condition monitoring10.1109/TSTE.2018.2816738 ↗
76. Fault feature extraction of low speed roller bearing based on Teager energy operator and CEEMD10.1016/j.measurement.2019.02.053 ↗
77. Gong, X., Qiao, W., and Zhou, W. (2010). Incipient bearing fault detection via wind generator stator current and wavelet filter. IECON 2010-36th Annual Conference on IEEE Industrial Electronics Society, IEEE.10.1109/IECON.2010.5675135 ↗
78. Gong, X., and Qiao, W. (2011). Bearing fault detection for direct-drive wind turbines via stator current spectrum analysis. 2011 IEEE Energy Conversion Congress and Exposition, IEEE.10.1109/ECCE.2011.6063785 ↗
79. Gong, X., and Qiao, W. (2012). Current-based online bearing fault diagnosis for direct-drive wind turbines via spectrum analysis and impulse detection. 2012 IEEE Power Electronics and Machines in Wind Applications, IEEE.10.1109/PEMWA.2012.6316398 ↗
80. Bearing fault diagnosis for direct-drive wind turbines via current-demodulated signals10.1109/TIE.2013.2238871 ↗
81. Bearing fault diagnosis of direct-drive wind turbines using multiscale filtering spectrum10.1109/TIA.2017.2650142 ↗
82. Current-aided order tracking of vibration signals for bearing fault diagnosis of direct-drive wind turbines10.1109/TIE.2016.2571258 ↗
83. A comprehensive review on signal-based and model-based condition monitoring of wind turbines: Fault diagnosis and lifetime prognosis10.1109/JPROC.2022.3171691 ↗
84. Isermann, R. (2006). Fault-Diagnosis Systems: An Introduction from Fault Detection to Fault Tolerance, Springer Science & Business Media.10.1007/3-540-30368-5 ↗
85. Fault-tolerant individual pitch control for load mitigation in wind turbines with actuator faults10.1109/TIE.2020.2965479 ↗
86. Results of a wind turbine FDI competition10.3182/20120829-3-MX-2028.00015 ↗
87. Chen, J., and Patton, R.J. (2012). Robust Model-Based Fault Diagnosis for Dynamic Systems, Springer Science & Business Media.
88. Kalman filtering with real time applications
89. Fault diagnosis of rotating machinery based on multisensor information fusion using SVM and time-domain features
90. Rotor-current-based fault diagnosis for DFIG wind turbine drivetrain gearboxes using frequency analysis and a deep classifier10.1109/TIA.2017.2773426 ↗
91. A fault diagnosis scheme for planetary gearboxes using adaptive multi-scale morphology filter and modified hierarchical permutation entropy10.1016/j.ymssp.2017.12.008 ↗
92. An improved hyper-sphere support vector machine10.1109/ICNC.2007.213 ↗
93. A fault diagnosis scheme for planetary gearboxes using modified multi-scale symbolic dynamic entropy and mRMR feature selection10.1016/j.ymssp.2016.12.040 ↗
94. Xiao, Y., Wang, Y., Mu, H., and Kang, N. (2017). Research on misalignment fault isolation of wind turbines based on the mixed-domain features. Algorithms, 10.10.3390/a10020067 ↗
95. An SVM-ANN hybrid classifier for diagnosis of gear fault10.1080/08839514.2017.1413066 ↗
96. Gear fault diagnosis under variable conditions with intrinsic time-scale decomposition-singular value decomposition and support vector machine10.1007/s12206-017-0107-3 ↗
97. Application of wavelet energy and Shannon entropy for feature extraction in gearbox fault detection under varying speed conditions10.1016/j.neucom.2013.12.018 ↗
98. Gear fault detection and diagnosis under speed-up condition based on order cepstrum and radial basis function neural network10.1007/s12206-009-0730-8 ↗
99. Chen, J., Li, Y., and Ye, F. (2016). Uncertain information fusion for gearbox fault diagnosis based on BP neural network and DS evidence theory. 2016 12th World Congress on Intelligent Control and Automation (WCICA), IEEE.10.1109/WCICA.2016.7578248 ↗
100. Jing, L., Wang, T., Zhao, M., and Wang, P. (2017). An adaptive multi-sensor data fusion method based on deep convolutional neural networks for fault diagnosis of planetary gearbox. Sensors, 17.10.3390/s17020414 ↗