A Methodology to Model Caving Initiation Using DEM
Source abstract
Abstract
The initiation of the caving process in block/panel caving is critical to the success of mines. However, there is no widely adopted methodology for modeling the onset of caving. This study proposes a methodology to model the initial stages of caving using the Discrete Element Method, in which the rock mass is represented using the Bonded Particle Model, and the undercut material is modeled with non-cohesive discrete particles. The collapse of the rock mass was replicated following a parameter calibration process, and the results were compared with actual mining data of the observed initial fragmentation. Key parameters were identified, such as allowable normal and shear stresses, which are essential to accurately represent the collapse of the rock mass and the evolution of the early stage of rock fragmentation. Low allowable stress values led to premature collapse and finer fragmentation, whereas higher values delayed cave back failure and resulted in coarser initial fragmentation. The results showed the formation of large rock fragments between 14 and 15 m during the initial cave back failures. Subsequently, larger fragments ranging from 2 to 9 m were observed detaching from the cave back as draw progressed, with sizes comparable to those reported in some block/panel caving operations. The main contribution of this work is a methodology that demonstrates the feasibility of modeling caving initiation, which is crucial in a context where increasing rock mass strength and deposit depth require design changes at the production level and pose significant uncertainty in the rock mass response.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Rock Mechanics and Modeling · Tailings Management and Properties · Karst Systems and Hydrogeology
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Faculty of Engineering, Universidad de Concepción, Concepción 4030000, Chile
Laboratory of Block Caving, Advanced Mining Technology Center, University of Chile, Santiago 4070371, Chile
Funding
Agencia Nacional de Investigación y Desarrollo · CONICYT
References (86)
Show source-provided references
1. Brown, E.T. (2007). Cave initation by undercutting. Block Caving Geomechanics, Julius Kruttschnitt Mineral Research Centre.
2. Design and evaluation of single-phase drawbell excavation at the Chuquicamata underground mine
3. Castro, R., Baez, F., and Suzuki, K. (2020). Undercutless caving at Newcrest: Towards the next generation of cave mining. Proceedings of the Eighth International Conference & Exhibition on Mass Mining, Massmin 2020, ACG.
4. Morales, D., Henriquez, J.P., and Castro, R. (2024). Impact of undercut geometry on caving propagation. Proceedings of the Massmin 2024: International Conference & Exhibition on Mass Mining, ACG.10.36487/ACG_repo/2435_D-15 ↗
5. Pierce, M.E., Cundall, P.A., Van Hout, G., and Lorig, L. (2017). PFC 3D modeling of caved rock under draw. Numerical Modeling in Micromechanics via Particle Methods, Taylor & Francis.10.1201/9780203745335-28 ↗
6. Numerical investigation of effect of particle shape on isolated extracted zone (IEZ) in block caving10.1007/s12517-018-3669-1 ↗
7. Potvin, Y., Carter, J., Dyskin, A., and Jeffrey, R. (2008). 3D simulations of block caving flow using ESyS-Particle. Proceedings of the SHIRMS 2008: First Southern Hemisphere International Rock Mechanics Symposium, Australian Centre for Geomechanics.
8. Hancock, W. (2013). Gravity Flow of Rock in Caving Mines: Numerical Modelling of Isolated, Interactive and Non-Ideal Draw. [Ph.D. Thesis, University of Queensland].
9. A Study of Gravity Flow Based on the Upside-Down Drop Shape Theory and Considering Rock Shape and Breakage10.1007/s00603-018-1514-1 ↗
10. Simulation of fines migration using a non-Newtonian lattice Boltzmann-discrete element model: Part II: 3D extension and applications10.1108/02644401211227635 ↗
11. McNamara, G.G., and Zanetti, G. (2019). Use of the Boltzmann equation to simulate lattice-gas automata. Lattice Gas Methods For Partial Differential Equations, CRC Press.
12. The influence of drawbell geometry on hang-ups during ore extraction
13. Castro, R., Valdés, C., Gómez, R., Skrzypkowski, K., and Zagórski, K. (2024). Design Parameters Affecting Rill Swell Events for Block Caving Applications. Appl. Sci., 14.10.3390/app14188545 ↗
14. Y-Geo: New Combined Finite-Discrete Element Numerical Code for Geomechanical Applications10.1061/(ASCE)GM.1943-5622.0000216 ↗
15. Lisjak, A., Tatone, B.S.A., Mahabadi, O.K., and Grasselli, G. (2012). Block caving modelling using the Y-Geo hybrid finite-discrete element code. Proceedings of the 6th International Conference & Exhibition on Mass Mining, Massmin 2012, Canadian Institute of Mining, Metallurgy and Petroleum.
16. A study of gravity flow principles of sublevel caving method in dipping narrow veins10.1007/s10035-017-0748-z ↗
17. Wang, L., Jing, H., Yu, J., and Liu, X. (2022). Impact of particle shape, size, and size distribution on gravity flow behaviour of broken ore in sublevel caving. Minerals, 12.10.3390/min12101183 ↗
18. A discrete element modelling of gravity flow in sublevel caving considering the shape and size distribution of particles10.1080/17480930.2023.2168870 ↗
19. Lapčević, V., and Torbica, S. (2017). Numerical investigation of caved rock mass friction and fragmentation change influence on gravity flow formation in sublevel caving. Minerals, 7.10.3390/min7040056 ↗
20. Chen, Q.Q., Qin, S., and Chen, Q.Q. (2019). Numerical Simulation of Ore Particle Flow Behaviour through a Single Drawpoint under the Influence of a Flexible Barrier. Geofluids, 2019.10.1155/2019/6127174 ↗
21. A review on the geotechnical design and optimisation of ultra-long ore passes for deep mass mining10.1007/s12665-024-11616-z ↗
22. Nazeri, H., and Mustoe, G.G. (2002). Application of DEM to simulate gravity flow of bulk solid materials in mines. Proceedings of the Discrete Element Methods: Numerical Modeling of Discontinua, ASCE.10.1061/40647(259)70 ↗
23. Numerical investigations of ore pass hang-up phenomena10.1016/j.ijrmms.2006.12.006 ↗
24. Analysis of Ore Pass Hang-Ups in Long Vertical Ore Passes by 3-D DEM
25. Influence of ore-drawing port position on ore-rock flow characteristics in ore pass and lateral pressure on ore pass wall10.1038/s41598-024-72032-8 ↗
26. Application of DFN–DEM modelling in addressing ground control issues at an underground mine10.1179/1743286315Y.0000000013 ↗
27. Experimental study of the fracturing process in brittle rock10.1029/JB073i004p01447 ↗
28. Fracture initiation and propagation in intact rock—A review10.1016/j.jrmge.2014.06.001 ↗
29. A microcrack model for the deformation and failure of brittle rock10.1029/JB088iB11p09485 ↗
30. Nucleation and growth of faults in brittle rocks10.1029/94JB00115 ↗
31. Microcracking in tensile fracture of a brittle rock10.1016/j.engfracmech.2021.107789 ↗
32. Microcracking during triaxial deformation of porous rocks monitored by changes in rock physical properties, I. Elastic-wave propagation measurements on dry rocks10.1016/0040-1951(94)00235-2 ↗
33. A discrete element model to describe failure of strong rock in uniaxial compression10.1007/s10035-010-0230-7 ↗
34. Evaluation of damage level for rock slopes using acoustic emission technique with waveguides10.1016/j.enggeo.2011.04.015 ↗
35. Quantitative damage, fracture mechanism and velocity structure tomography of sandstone under uniaxial load based on acoustic emission monitoring technology10.1016/j.conbuildmat.2020.121911 ↗
36. Analysis of mafic rocks microstructure damage and failure process under compression test using quantitative scanning electron microscopy and digital images processing10.1016/j.engfracmech.2020.107019 ↗
37. The bonded-particle model as a tool for rock mechanics research and application: Current trends and future directions10.1080/12269328.2014.998346 ↗
38. Zhou, C., Qiu, J., Karakus, M., Wang, C., Feng, F., Wang, F., and Zhou, T. (2026). Unraveling rate-strengthening and fracture-weakening effects in fractured rock masses: A hybrid bonded particle model-discrete fracture network and physics-inspired machine learning framework. J. Rock Mech. Geotech. Eng.10.1016/j.jrmge.2025.08.055 ↗
39. Numerical and experimental assessment of the sandstone fracture mechanism by non-uniform bonded particle modeling10.1007/s00603-021-02620-x ↗
40. Sainsbury, B.-A. (2012). A Model for Cave Propagation and Subsidence Assessment in Jointed Rock Masses. [Ph.D. Thesis, The University of New South Wales].
41. Application of Finite Element Method for Simulation of Rock Mass Caving Processes in Block Caving Method
42. Vidal, R., Vallejos, J.A., Cuello, D., and Cifuentes, C. (2024). Back analysis of caving propagation using numerical models in Esmeralda Sur mine. Proceedings of the Massmin 2024: International Conference & Exhibition on Mass Mining, ACG.10.36487/ACG_repo/2435_D-11 ↗
43. Itasca Consulting Group, Inc. (2017). FLAC3D 6.0 Theory and Background, Itasca Consulting Group, Inc.. Available online: https://itasca-software.s3.amazonaws.com/resources/flac3d_600_theory.pdf.
44. Potvin, Y., Carter, J., Dyskin, A., and Jeffrey, R. (2008). Analysis of Caving Behaviour Using a Synthetic Rock Mass—Ubiquitous Joint Rock Mass Modelling Technique. Proceedings of the SHIRMS 2008, Australian Centre for Geomechanics.
45. Sainsbury, B.L.L., Sainsbury, D.P.P., and Pierce, M.E. (2011). A historical review of the development of numerical cave propagation simulations. Proceedings of the 2nd International FLAC/DEM Symposium, Itasca International Inc.
46. Sainsbury, D.P., Sainsbury, B.L., Board, M.P., and Loring, D.M. (2011). Numerical Back-Analysis of Structurally Controlled Cave Initiation And Propagation At the Henderson Mine. Proceedings of the ARMA, OnePetro.
47. Sainsbury, B.-A., Sainsbury, D., and Carroll, D. (2018). Back-analysis of PC1 cave propagation and subsidence behaviour at the Cadia East mine. Proceedings of the Caving 2018: Proceedings of the Fourth International Symposium on Block and Sublevel Caving, Australian Centre for Geomechanics.10.36487/ACG_rep/1815_10_Sainsbury ↗
48. Potvin, Y. (2022). A coupled modelling approach for discontinuous subsidence at the Cadia East mine. Proceedings of the Caving 2022: Fifth International Conference on Block and Sublevel Caving, Australian Centre for Geomechanics.
49. Beck, D.A., and Putzar, G. (2011). Coupled flow-deformation simulation for mine scale analysis of cave initiation and propagation. Proceedings of the International Society of Rock Mechanics Congress, ISRM.10.1201/b11646-60 ↗
50. Beck, D.A., Sharrock, G., and Capes, G. (2011, January 26–29). A coupled DFE-Newtonian Cellular Automata scheme for simulation of cave initiation, propagation and induced seismicity. Proceedings of the 45th US Rock Mechanics/Geomechanics Symposium2, San Francisco, CA, USA.
51. Potvin, Y., and Jakubec, J. (2018). Three-dimensional simulation of cave initiation, propagation and surface subsidence using a coupled finite difference–cellular automata solution. Proceedings of the Fourth International Symposium on Block and Sublevel Caving, Caving 2018, ACG.
52. Arndt, S., Bui, T., Diering, T., Austen, I., and Hocking, R. (2018). Integrated simulation and optimisation tools for production scheduling using finite element analysis caving geomechanics simulation coupled with 3D cellular automata. Proceedings of the Caving 2018, ACG.10.36487/ACG_rep/1815_16_Arndt ↗
53. Fracture banding in caving mines10.17159/2411-9717/2016/v116n8a7 ↗
54. Jacobsz, S.W., Kearsley, E.P., Cumming-Potvin, D., and Wesseloo, J. (2018). Modelling cave mining in the geotechnical centrifuge. Physical Modelling in Geotechnics, Volume 2, CRC Press.10.1201/9780429438646-6 ↗
55. Potvin, Y., and Jakubec, J. (2018). A re-evaluation of the conceptual model of caving mechanics. Proceedings of the Caving 2018, Australian Centre for Geomechanics.
56. The effect of overburden and confined stress state on cave mining propagation
57. Ansys, Inc. (2022). ESSS Rocky DEM 2022, Ansys, Inc.
58. André, F.P., Potapov, A., Maliska, C., and Tavares, L.M. (2019). Simulation of single particle breakage using non-Round particles in Rocky DEM. Proceedings of the IMCET 2019-Proceedings of the 26th International Mining Congress and Exhibition of Turkey, Baski.
59. Moncada, M., Toledo, P., Betancourt, F., and Rodríguez, C. (2021). Torque Analysis of a Gyratory Crusher with the Discrete Element Method. Minerals, 11.10.3390/min11080878 ↗
60. Gómez, R., Skrzypkowski, K., Moncada, M., Castro, R., and Lazo, R. (2022). Segregation Modeling in Stockpile Using Discrete Element Method. Appl. Sci., 12.10.3390/app122312449 ↗
61. Potvin, Y., and Jakubec, J. (2018). Experiments and simulation of gravity flow in block caving through FlowSim. Proceedings of the Fourth International Symposium on Block and Sublevel Caving, Caving 2018, ACG.
62. Brown, E. (2007). Fragmentation Assessment. Block Caving Geomechanics, JKMRC.
63. Andreotti, B., Forterre, Y., and Pouliquen, O. (2013). Granular Media: Between Fluid and Solid, Cambridge University Press.10.1017/CBO9781139541008 ↗
64. Block Caving y LHD: Reflexiones sobre mallas de extracción
65. Johnson, K.L. (1987). Contact Mechanics, Cambridge University Press.
66. An automatic procedure for train speed evaluation by the dominant frequency method10.1016/j.compgeo.2011.02.003 ↗
67. CPFD simulation on wear mechanisms in disk–donut FCC strippers10.1016/j.powtec.2015.04.012 ↗
68. A bond model for DEM simulation of cementitious materials and deformable structures10.1007/s10035-014-0494-4 ↗
69. Characterization of clastic rock using a biconcave bond model of DEM10.1002/nag.2568 ↗
70. Rolling friction as a technique for modelling particle shape in DEM10.1016/j.powtec.2011.10.057 ↗
71. Investigation of modeling non-spherical particles by using spherical discrete element model with rolling friction10.1016/j.enganabound.2019.04.013 ↗
72. Development of a standard calibration procedure for the DEM parameters of cohesionless bulk materials–part I: Solving the problem of ambiguous parameter combinations10.1016/j.powtec.2018.11.034 ↗
73. Determination of drawpoint spacing in panel caving: A case study at the el teniente mine
74. A bonded-particle model for rock10.1016/j.ijrmms.2004.09.011 ↗
75. Karzulovic, A., and Alfaro, M. (2004). Visual estimation of fragment size distributions in the DOZ block cave. Proceedings of the Massmin 2004, Instituto de Ingenieros de Chile.
76. Hurtado, J., Pereira, J., and Campos, R. (2007). Informe Final Backanalysis De Fragmentación, Minas: Diablo Regimiento, Reno Y Teniente 4 Sur Tonalita. Nnm-Ico-Geo-Inf No 003, Codelco.
77. Brunton, I., Lett, J.L., and Thornhill, T. (2016). Fragmentation prediction and assessment at the Ridgeway Deeps and Cadia East cave operation. Proceedings of the Seventh International Conference & Exhibition on Mass Mining, Massmin 2016, AusIMM.
78. Volumetric fracture intensity measurement for improved rock mass characterization and fragmentation assessment in block caving operations10.1007/s00603-014-0592-y ↗
79. Schunnesson, H., and Nordlung, E. (2008). Impact of rock type variability on production rates and scheduling at the DOZ-ESZ block cave mine. Proceedings of the 5th Conference and Exhibition on Mass Mining, Lulea University of Technology.
80. A Comminution Model for Secondary Fragmentation Assessment for Block Caving10.1007/s00603-017-1267-2 ↗
81. Potvin, Y., and Jakubec, J. (2018). Influence of the undercut height on the behaviour of pillars at the extraction level in block and panel caving operations. Proceedings of the Caving 2018, Australian Centre for Geomechanics.
82. Batkhuu, B., van As, A., and Lett, J. (2024). Evolution of undercutting in panel and block caves. Proceedings of the Massmin 2024: International Conference & Exhibition on Mass Mining, ACG.10.36487/ACG_repo/2435_R-07 ↗
83. Physical modelling of ore flow in ore passes for haulage decarbonisation in deep mining10.1016/j.ijrmms.2025.106302 ↗
84. Laubscher, D. (2000). Block Cave Manual, Julius Kruttschnitt Mineral Research Centre.
85. Hoek, E., Wyllie, D.C., and Stewart, S. (1980). Prediction of Stable Excavation Spans for Mining Below 1000 Meters in Hard Rock, Golder Associates.
86. A wet muck entry model: A case study for long-term planning at El Teniente mine10.1080/17480930.2023.2265646 ↗