Modeling Heat Consumption of an Office Building During COVID-19 Restrictions
Source abstract
Abstract
COVID-19 restricted the number of employees. Operational data showed that traditional methods of modeling heat consumption are not correct anymore. The aim is to model the energy demand of an office building during COVID-19 limitations and showcase improvements after a new controller or suggested alternatives are applied. After an actual heat consumption profile was simulated, energy conservation scenarios were considered: the usage of thermostatic radiator valves (TRVs); accounting impacts of solar radiation and wind; changing mass flow rates based on the indoor temperature; adopting an additional control, changing the temperature setpoint; introducing night and day setbacks. After implementing new design and operational methods, the overheating of indoor spaces was alleviated, and the average indoor temperature was reduced from 23.5 °C to 20.4 °C. The annual specific heat consumption decreased to 174 kWh/m2 (20.2% lower). The methodology ensured thermal comfort and high energy-saving potential. If operating parameters were adjusted, the total saving effect in energy demand was 119.8 MWh, with an energy-saving rate of 19.8%. Employing TRV-related savings and considering thermal inertia provided more stable indoor temperatures and higher energy performance. The minimum saving effect corresponded to the optimal operation and ensuring the indoor environment by considering wind and the maximum one-to-night setbacks. The fluctuations in indoor temperature became smoother.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Building Energy and Comfort Optimization · Wind and Air Flow Studies · Infection Control and Ventilation
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Energy Engineering Department, Omsk State Transport University (OSTU), 35 Marx Avenue, 644046 Omsk, Russia
Funding
VLAIO in Belgium, ICON project OPTIMESH
References (25)
Show source-provided references
1. The COVID-19 pandemic: Workplace safety management practices, job insecurity, and employees’ organizational citizenship behavior10.1016/j.ssci.2021.105527 ↗
2. Determining the optimum low-temperature district heating network design for a secondary network supplying a low-energy-use apartment block in Ireland10.1016/j.energy.2019.116595 ↗
3. Multi-energy systems fast optimization: A new formulation in linear programming for temperatures and magnitudes of thermal power flows in heating systems10.1016/j.enbuild.2025.115618 ↗
4. Construction of linear temperature model using non-dimensional heat exchange ratio: Towards fast prediction of indoor temperature and heating, ventilation and air conditioning systems control10.1016/j.enbuild.2021.111351 ↗
5. Energy flexibility potential of a small district connected to a district heating system10.1016/j.enbuild.2020.110074 ↗
6. A dynamic control strategy of district heating substations based on online prediction and indoor temperature feedback10.1016/j.energy.2021.121228 ↗
7. Impact of thermal masses on the peak load in district heating systems10.1016/j.energy.2020.118849 ↗
8. A simulation-based evaluation of substation models for network flexibility characterisation in district heating networks10.1016/j.energy.2020.117650 ↗
9. Achieving low return temperatures from district heating substations10.1016/j.apenergy.2014.09.022 ↗
10. Control schemes for district heating substations considering user-defined building’s indoor temperature10.1016/j.buildenv.2021.107598 ↗
11. A new feedback predictive model for improving the operation efficiency of heating station based on indoor temperature10.1016/j.energy.2021.119961 ↗
12. Deep reinforcement learning to optimise indoor temperature control and heating energy consumption in buildings10.1016/j.enbuild.2020.110225 ↗
13. Influence of envelope, structural thermal mass and indoor content on the building heating energy flexibility10.1016/j.enbuild.2018.11.012 ↗
14. Buildings and a district heating network as thermal energy storages in the district heating system10.1016/j.enbuild.2018.09.015 ↗
15. A comparative study on convective heat transfer in indoor applications10.1016/j.enbuild.2021.110985 ↗
16. Evaluating innovative collective heating and cooling concepts by incorporating occupants’ preferences for conflicting performance indicators10.1016/j.enbuild.2024.114264 ↗
17. Large-scale monitoring of operationally diverse district heating substations: A reference-group based approach10.1016/j.engappai.2020.103492 ↗
18. Costs and benefits of preparing existing Danish buildings for low-temperature district heating10.1016/j.energy.2019.03.186 ↗
19. Optimizing the renewable and fossil-fired generation capacities: Case study of interconnected district-level systems10.1016/j.egyr.2021.11.095 ↗
20. Heat demand forecasting algorithm for a Warsaw district heating network10.1016/j.energy.2020.119347 ↗
21. Splitting measurements of the total heat demand in a hotel into domestic hot water and space heating heat use10.1016/j.energy.2020.119685 ↗
22. A novel dynamic simulation model for the thermo-economic analysis and optimisation of district heating systems10.1016/j.enconman.2020.113052 ↗
23. Analysis of operational data from a district cooling system and its connected buildings10.1016/j.energy.2020.117844 ↗
24. (2008). Energy Performance of Buildings-Calculation of Energy Use for Space Heating and Cooling (Standard No. EN ISO 13790:2008).
25. Optimizing building heat consumption: Weekday and weekend profiles10.1016/j.egyr.2021.06.029 ↗