Study of the Dependence of the Properties of the Ti EBPVD Layer Deposited on the Inner Surface of the Tube on the Position of the Evaporated Target Using the Statistical Methods
Source abstract
Abstract
This article presents the properties of a Ti coating (angle of grain growth, thickness of the deposited layer, adhesion, and roughness of the deposited layer) deposited on the inner surface of a steel tube. The Ti coating was deposited using the EB PVD (electron beam physical vapor deposition) method. The areas in which the measurements were carried out are defined by the height of the measured area under the target (from 305 to 425 mm) and the radius of the tube (from 100 to 140 mm). The measurements showed that the angle of grain growth is in an interval from 40 to 61°. The results of the statistical analysis demonstrate that the height of the measured area and the tube radius significantly impact the angle of grain growth and adhesion. On the other hand, the impact of the height of the measured area and the tube radius on the roughness of the applied coating was not confirmed.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Advanced materials and composites · High-Temperature Coating Behaviors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Faculty of Mechanical Engineering, Technical University of Kosice, Letna 9, 042 00 Kosice, Slovakia
Faculty of Special Technology, Alexander Dubcek University of Trencin, Ku kyselke 469, 911 06 Trencin, Slovakia
Faculty of Electrical Engineering and Informatics, Technical University of Kosice, Letna 9, 042 00 Kosice, Slovakia
References (24)
Show source-provided references
1. Bhushan, B., and Gupta, B.K. (1991). Handbook of Tribolohy, McGraw-Hill Inc.
2. High Rate Thick Film Growth10.1146/annurev.ms.07.080177.001323 ↗
3. Low energy ion assist during deposition—An effective tool for controlling thin film microstructure10.1016/S0168-583X(97)00010-4 ↗
4. Incident flux angle induced crystal texture transformation in nanostructured molybdenum films10.1063/1.4737403 ↗
5. The study of selected properties of Ti EB PVD coating deposited onto inner tube surface at low temperature10.1515/amm-2016-0016 ↗
6. Improvement of plasma uniformity and mechanical properties of Cr films deposited on inner surface of tube by auxiliary anode near tube tail10.1088/2058-6272/ac57fd ↗
7. Michau, A., Maury, F., Schuster, F., Nuta, I., Gazal, Y., Boichot, R., and Pons, M. (2018). Chromium Carbide Growth by Direct Liquid Injection Chemical Vapor Deposition in Long and Narrow Tubes, Experiments, Modeling and Simulation. Coatings, 8.10.3390/coatings8060220 ↗
8. DLC deposition inside of a long tube by using the pulsed-DC PECVD process10.1016/j.surfcoat.2018.12.011 ↗
9. Observation of uniformity of diamond-like carbon coatings utilizing hollow cathode discharges inside metal tubes10.1016/j.surfcoat.2019.07.024 ↗
10. Plasma immersion ion implantation into cylindrical bore using internal inductively coupled radio-frequency discharge10.1016/j.surfcoat.2012.05.118 ↗
11. TiN films deposition inside stainless-steel tubes using magnetic field-enhanced arc ion plating10.1016/j.vacuum.2014.11.014 ↗
12. Ion current on the inner surface of a pipe by plasma-based ion implantation and deposition10.1016/S0168-583X(03)00855-3 ↗
13. Coating and ion implantation to the inner surface of a pipe by metal plasma-based ion implantation and deposition10.1016/S0257-8972(03)00140-3 ↗
14. Modeling of plasma spray coating process using statistical regression analysis10.1007/s00170-012-4232-y ↗
15. Regression analysis of bonding strength of sprayed coatings based on acoustic emission signal10.3139/146.111169 ↗
16. Adhesion evaluation of plasma sprayed coatings using piecewise linear regression analysis10.1361/105996399770350214 ↗
17. Analysis of coating weight and iron content for iron-zinc alloy coatings by using X-ray fluorescence with multiple regression
18. Chen, J., and Xu, L.M. (2008, January 5–8). Experimental Analysis of a Protective Wafer Coating Process for the Die Preparation. Proceedings of the IEEE International Conference on Mechatronics and Automation: (ICMA), Takamatsu, Japan.10.1109/ICMA.2008.4798796 ↗
19. Investigation and modeling of the SMAW coating flux thermal properties using neural network and regression analysis10.1016/j.ceramint.2023.02.141 ↗
20. Wettability studies of formulated SMAW electrode coating fluxes with regression analysis and neural network approach10.1016/j.ceramint.2022.11.201 ↗
21. Analysis of Regression and Grey Relational Degree of Uniform Design on Composition of RuIrSnLa/Ti Metallic-oxide Anode Coatings
22. Zhang, H., Pan, Y.J., Zhang, Y., Lian, G.F., Cao, Q., and Yang, J.H. (2022). Sensitivity Analysis for Process Parameters in Mo2FeB2 Ternary Boride Coating by Laser Cladding. Coatings, 12.10.3390/coatings12101420 ↗
23. Experimental investigation on SMAW electrode coatings developed using CaO-SiO2-CaF2-SrO based coating system10.1016/j.ceramint.2022.06.187 ↗
24. Policastro, S.A., Anderson, R.M., Hangarter, C.M., Arcari, A., and Iezzi, E.B. (2023). Incorporating Physics-Based Models into Equivalent Circuit Analysis of EIS Data from Organic Coatings. Coatings, 13.10.3390/coatings13071285 ↗