The Assessment of the Maximum Heat Production and Cooling Effectiveness of Three Different Drill Types (Conical vs. Cylindrical vs. Horizontal) during Implant Bed Preparation—An In Vitro Study
Source abstract
Abstract
The aim of this experimental study was to verify thermal diffusion differences, by measuring the maximum temperature achieved with different drill shapes. Synthetic bone blocks of type I density made from solid rigid polyurethane (PUR) foam were used to perform the drilling procedures. The experiment was conducted at three different rotation speeds: 800, 3000 and 5000 rpm. Conical drills (with and without an internal cooling hole) were compared with horizontal drills and disc drills. The temperature during drilling for implant bed preparation was estimated with the use of thermocouples and an infrared (IR) camera. The temperature during drilling with disc cutters for lateral basal implants did not exceed 33 ∘C and the temperature decreased in proportion to higher drill speed. The results indicate that the tested design is safe and will not cause bone overheating.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Dental Implant Techniques and Outcomes · Dental materials and restorations · Orthopaedic implants and arthroplasty
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Clinic for Maxillofacial Surgery, University of Belgrade, 11-000 Belgrade, Serbia
Department of Dental Prosthetics, Pomeranian Medical University, 70-111 Szczecin, Poland
Private Dental Practice, 68-200 Żary, Poland
References (36)
Show source-provided references
1. Heat generated by dental implant drills during osteotomy—A review: Heat generated by dental implant drills10.1007/s13191-014-0350-6 ↗
2. In Vitro Assessment with the Infrared Thermometer of Temperature Differences Generated During Implant Site Preparation: The Traditional Technique Versus the Single-Drill Technique10.1111/cid.12246 ↗
3. Novel hybrid drilling protocol: Evaluation for the implant healing--thermal changes, crestal bone loss, and bone-to-implant contact10.1111/clr.12341 ↗
4. The effect of low-speed drilling without irrigation on heat generation: An experimental study10.5125/jkaoms.2016.42.1.9 ↗
5. José, L.F.D.S., Ruggeri, F.M., Rucco, R., Zubizarreta-Macho, A., Pérez-Barquero, J.A., Deglow, E.R., and Montero, S.H. (2020). Influence of Drilling Technique on the Radiographic, Thermographic, and Geomorphometric Effects of Dental Implant Drills and Osteotomy Site Preparations. J. Clin. Med., 9.10.3390/jcm9113631 ↗
6. A novel drilling procedure and subsequent bone autograft preparation: A technical note
7. Influence of bone density, drill diameter, drilling speed, and irrigation on temperature changes during implant osteotomies: An in vitro study
8. Temperature threshold levels for heat-induced bone tissue injury: A vital-microscopic study in the rabbit10.1016/0022-3913(83)90174-9 ↗
9. Osseointegrated titanium implants: Requirements for ensuring a long-lasting, direct bone-to-implant anchorage in man10.3109/17453678108991776 ↗
10. Effect of simplifying drilling technique on heat generation during os-teotomy preparation for dental implant10.1097/ID.0000000000000692 ↗
11. Experimental analysis of temperature differences during implant site preparation: Continuous drilling technique versus intermittent drilling technique10.1563/aaid-joi-D-17-00077 ↗
12. Effect of insertion factors on dental implant insertion torque/energy-experimental results10.1016/j.jmbbm.2020.103995 ↗
13. Effect of implant drill characteristics on heat generation in osteotomy sites: A pilot study10.1111/j.1600-0501.2010.02051.x ↗
14. A novel standardized bone model for thermal evaluation of bone osteotomies with various irrigation methods10.1111/clr.12090 ↗
15. Drilling- and Withdrawing-Related Thermal Changes during Implant Site Osteotomies10.1111/cid.12091 ↗
16. Temperature Changes in Cortical Bone after Implant Site Preparation Using a Single Bur versus Multiple Drilling Steps: An In Vitro Investigation10.1111/cid.12172 ↗
17. Horak, Z., Dvorak, K., Zarybnicka, L., Vojackova, H., Dvorakova, J., and Vilimek, M. (2020). Experimental Measurements of Mechanical Properties of PUR Foam Used for Testing Medical Devices and Instruments Depending on Temperature, Density and Strain Rate. Materials, 13.10.3390/ma13204560 ↗
18. Fahmina Zafar, F. (2012). Use of Polyurethane Foam in Orthopaedic Biomechanical Experimentation and Simulation, Polyurethane, InTech.
19. Horn, T.J., Harrysson, O.L.A., Little, J.P., West, H.A., and Marcellin-Little, D.J. (2010, January 9–11). Design and manufacturing of bone analog models for the mechanical evaluation of custom medical implants. Proceedings of the 21st Annual International Solid Freeform Fabrication Symposium—An Additive Manufacturing Conference, SFF 2010, Austin, TX, USA.
20. Implant-protected occlusion: A biomechanical rationale
21. Effect of Surgical Drill Guide on Heat Generated from Implant Drilling10.1016/j.joms.2009.07.056 ↗
22. Influence of tool geometry on drilling performance of cortical and trabecular bone10.1016/j.medengphy.2012.12.004 ↗
23. Investigation of the effect of movement and irrigation systems on temperature in the conventional drilling of cortical bone10.1016/j.bjoms.2012.10.023 ↗
24. The influence of drilling pulling ways and cooling systems on dental implant surgery
25. Osteotomy at low-speed drilling without irrigation versus high-speed drilling with irrigation: An experimental study
26. Kosior, P., Kuropka, P., Janeczek, M., Mikulewicz, M., Zakrzewski, W., and Dobrzyński, M. (2021). The Influence of Various Preparation Parameters on the Histological Image of Bone Tissue during Implant Bed Preparation—An In Vitro Study. Appl. Sci., 11.10.3390/app11041916 ↗
27. Bite Reconstruction in the Aesthetic Zone Using One-Piece Bicortical Screw Implants
28. Immediately Loaded Bicortical Implants Inserted in Fresh Extraction and Healed Sites in Patients with and Without a History of Periodontal Disease10.4103/ams.ams_147_19 ↗
29. Peri-Implant Bone Behavior after Single Drill versus Multiple Sequence for Osteotomy Drill10.1155/2018/9756043 ↗
30. Heat distribution in bone during preparation of implant sites: Heat analysis by real-time thermography
31. Assessment of Stability of Craniofacial Implants by Resonant Frequency Analysis10.1097/SCS.0000000000002443 ↗
32. Vitomir, K.S., Filip, I., Vojkan, L., Igor, Đ., and Lukasz, P. (2020). Survival rate of disk and screw-type implants used for the retention of extraoral prostheses. J. Prosthet. Dent.
33. Simplified Drilling Technique Does Not Decrease Dental Implant Osseointegration: A Preliminary Report10.1902/jop.2012.120565 ↗
34. Effect of the Drilling Technique on Heat Generation During Osteotomy Preparation for Wide-Diameter Implants10.1097/ID.0000000000000482 ↗
35. Implant site preparation using a single bur versus multiple drilling steps: 4-month post-loading results of a multicenter randomised controlled trial
36. Effect of low speed drilling on os-se-ointegration using simplified drilling procedures10.1016/j.bjoms.2015.03.010 ↗