Design of Non-Intrusive Online Monitoring System for Traction Elevators
Source abstract
Abstract
With the increase in elevator usage, more and more elevator real-time monitoring equipment is being applied to the operation of elevators. Traditional elevator monitoring equipment adopts a multi-sensor decentralized installation and layout, and the monitoring accuracy is low, which directly affects the effective alarm of the monitoring system; however, existing online monitoring systems cannot quickly alarm for faults. Aiming to solve the above problems, an elevator online monitoring system based on narrow-band Internet of Things (NB-IoT) is designed. The system is highly integrated with an STM32 main control chip, a six-axis acceleration gyroscope sensor, and an air pressure sensor to realize the edge calculation of the monitoring system. At the same time, this paper eliminates the temperature drift of the pressure sensor by using a temperature compensation algorithm and inputs the extracted characteristic parameters into the BP neural network for training to eliminate the zero drift so as to obtain the real-time height data of the elevator. The six-axis acceleration gyroscope sensor is used to calculate the posture so as to avoid the problem that a three-axis acceleration sensor or a three-axis gyroscope sensor alone cannot obtain accurate posture data. In order to further improve the monitoring accuracy, the peak-to-peak value of the signal is calculated by using a 95% confidence interval algorithm to reduce the suppression of the high-frequency components of the signal by noise and ensure that the signal has a large signal-to-noise ratio so that the obtained elevator car posture and vibration operation data are more accurate. Finally, the effectiveness of the proposed method is verified by experiments.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Elevator Systems and Control · IoT-based Smart Home Systems · Smart Parking Systems Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
School of Mechanical-Electronic and Vehicle Engineering, Beijing University of Civil Engineering and Architecture, Beijing 100044, China
References (29)
Show source-provided references
1. State Administration for Market Regulation (2022). Circular of the General Administration of Market Supervision on the Safety Condition of National Special Equipment in 2021. China Spec. Equip. Saf., 38, 1–4.
2. Design of wireless monitoring system for pump group based on internet of things
3. (2002). Measurement and Evaluation of Mechanical Vibration of Machines on Non-Rotating Parts Part 5: Hydroelectric Power Plants and Pumping Station Units (Standard No. GB/T 6075.5-2002).
4. (2008). Measurement and Evaluation of Radial Vibration of Rotating Machinery Rotor Shafts Part 5: Hydroelectric Power Plants and Pumping Station Units (Standard No. GB/T 11348.5-2008).
5. (2002). Mechanical Vibration-Evaluation of Machine Vibration by Measurements on Non-Rotating Parts: Part 5. Machine Sets in Hydraulic Power Machine Sets in Hydraulic Power Generating and Pumping Plants (Standard No. ISO 10816-2000).
6. (2016). Mechanical Vibration—Measurement and Evaluation of Machine Vibration—Part 5: Machine Sets in Hydraulic Power Generating and Pump-Storage Plants (Standard No. ISO 20816-5-2018).
7. Research on the calculation method of peak and peak values of main shaft oscillation of hydroelectric units under steady state working condition
8. EMD-based load shedding spindle oscillation of hydropower units
9. (2017). Field Test Protocol for Vibration and Pulsation of Hydraulic Machinery (Hydraulic Turbines, Storage Pumps and Pump Turbines) (Standard No. GB/T 17189-2017).
10. (2017). Guide for Field Measurement of Vibrations and Pulsations in Hydraulic Machines (Turbines, Storage Pumps and Pumpturbines) (Standard No. IEC 60994-2017).
11. (2018). Part 2: Land-based Gas Turbines, Steam Turbines and Generators in Excess of 40 MW, with Fluid-Film Bearings and Rated Speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min (Standard No. ISO 20816-2017).
12. Research on elevator operation state monitoring and fault remote alarm system
13. Design of custom communication protocol elevator monitoring system based on STM32F103ZET6
14. Research on elevator fault diagnosis and prediction based on big data
15. A non-intrusive intelligent monitoring method for elevator operation status
16. Design of real-time monitoring system for elevator based on internet of things
17. Design of elevator acceleration monitoring system based on cloud platform
18. Research on elevator condition monitoring technology based on vibration analysis
19. Research on fault diagnosis of elevator drum brake based on VMD and SVM
20. Research on thermal response characteristics of elevator inverter based on infrared thermal imaging
21. Nakanishi, H., Kanata, S., and Sawaragi, T. (2012, January 5–8). GPS-INS-BARO hybrid navigation system taking into account ground effect for autonomous unmanned helicopter. Proceedings of the 2012 IEEE International Symposium on Safety, Security, and Rescue Robotics (SSRR), College Station, TX, USA.10.1109/SSRR.2012.6523885 ↗
22. Automatic correction of barometric altimeters using additional air temperature and humidity measurements10.1007/s10291-023-01582-7 ↗
23. Fast Elevator Vibration Signal Cloud Collection System Using Data Compression and Encryption Algorithms
24. Early fault detection of elevators using remote condition monitoring through IoT technology
25. Design and realization of smart gas meter system based on narrowband IoT
26. Design of elevator monitoring system based on LoRa and STM32
27. Research on embedded elevator operation state monitoring system
28. Dangana, M., Ansari, S., Abbasi, Q.H., Hussain, S., and Imran, M.A. (2021). Suitability of NB-IoT for indoor industrial environment: A survey and insights. Sensors, 21.10.3390/s21165284 ↗
29. (2009). Specification for Electric Lifts (Standard No. GB/T 10058-2009).