Identification of the Wear Margin of a Pipeline–Machine Subsystem
Source abstract
Abstract
The quality of company asset management is significantly dependent on the quality of a system for asset wear margin identification. A pipeline–machine subsystem may be an essential part of assets in many production companies. It is necessary to build models of pipeline–machine subsystems and models of a system for the identification of subsystem wear margin. The method used consists of a decomposition of desired characteristics of an enterprise into desired characteristics of a pipeline–machine subsystem. Methods for the identification of real characteristics of a subsystem depend on the character of subsystem operation. In this study, hydrodynamic and thermodynamic models of the subsystem are built. Tests are conducted on industrial and laboratory objects. The boundaries of the subsystem are defined and changes in pressure, temperature and mass flow rate in the pipeline are presented. Causes of changes in the mentioned quantities are described. Desired characteristics of the subsystem resulting from decomposition are described. The presented methods of determining efficiency for steady working conditions and open flow use hydrodynamic and thermodynamic models. Energy efficiency of the subsystem is decomposed into efficiencies of main elements of the subsystem. A method is proposed for determining the subsystem’s energy efficiency in the case of the flow into a closed vessel. It is possible to determine the hydraulic efficiency of the subsystem components: the suction pipe, the discharge pipe and the machine. The efficiency of the machine determined by the hydrodynamic method is complementary to the efficiency obtained by the thermodynamic method. The machine set efficiency is composed of hydraulic efficiency of the machine; mechanical efficiency of the machine, the gearbox and motor; and electric efficiency of the motor. Hydraulic efficiency of the pipeline is related to substitute measure of wear margin—the coefficient of resistance. Pressure drop is a diagnostic symptom. Thermal efficiency of the heat exchanger is related to a substitute measure of wear margin—the coefficient of heat penetration. Temperatures and mass flow rate in the heat exchanger are diagnostic symptoms. It is possible to determine the capacity and efficiency of subsystems with one side closed—such as those filling hydrophore and gas vessels.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Engineering Diagnostics and Reliability · Material Properties and Failure Mechanisms · Oil and Gas Production Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Faculty of Marine Engineering, Maritime University of Szczecin, 70-500 Szczecin, Poland
References (46)
Show source-provided references
1. (2014). ISO 55000:2014. Asset management—Overview, Principles and Terminology, International Organization for Standardization.
2. (2018). ISO 17359:2018. Condition Monitoring and Diagnostics of Machines—General Guidelines, International Organization for Standardization.
3. (2016). ABS Guidance Notes on Equipment Condition Monitoring Techniques, American Bureau of Shipping.
4. (2010). BS EN 13306:2010. English Version EN 13306:2010 Maintenance—Maintenance Terminology, British Standards Institution.
5. The Functional quality signatures of man-machine system
6. (1982). PN-82/N-04001. Exploitation of Technical Objects—Terminology, Polish Committee for Standardization.
7. (2012). DIN 31051:2012-09. Fundamentals of Maintenance, German Institute for Standardization.
8. Measures and limits of machine wear margin of production systems
9. Korbicz, J., Kościelny, J.M., Kowalczuk, Z., and Cholewa, W. (2004). Fault Diagnosis. Models, Artificial Intelligence, Application, Springer.10.1007/978-3-642-18615-8 ↗
10. Ruan, D. (1997). Nonliner system identification with neuro-fuzzy methods. Intelligent Hybrid Systems, Springer.10.1007/978-1-4615-6191-0 ↗
11. Method of Multiple Fault Isolation in Large Scale Systems10.1109/TCST.2011.2162587 ↗
12. Stępniewski, M. (1985). Pumps, WNT. [2nd ed.]. (in Polish).
13. Mieszkowski, M. (1985). Thermal and Energy Measurements, WNT. (in Polish).
14. Clifford, T. (2016). Severn Trend Water Melbourne Real Time Pump and Turbine Network Optimisation, Pump Centre Conference. Available online: https://riventa.com/wp-content/uploads/2016/05/Riventa-Pump-Centre-Conference-Keynote-2016.pdf.
15. Probable shape of pipeline characteristic curves
16. Jędral, W. (2001). Rotodynamic Pumps, Wydawnictwo Naukowe PWN. (in Polish).
17. (2012). ISO 9906:2012. Rotodynamic Pumps—Hydraulic Performance Acceptance tests—Grades 1, 2 and 3, International Organization for Standardization.
18. Timashev, S., and Bushinskaya, A. (2016). Diagnostics and Reliability of Pipeline Systems, Springer.10.1007/978-3-319-25307-7 ↗
19. Jędral, W. (2007). Efficiency of Pumps and Pumping Installations, Krajowa Agencja Poszanowania Energii S.A.. (in Polish).
20. Timofiejczuk, A., Łazarz, B.E., Chaari, F., and Burdzik, R. (2018). Failure Analysis of Hydrogen Piston Compressors. Advances in Technical Diagnostics, Springer.10.1007/978-3-319-62042-8 ↗
21. Failure analysis of refinery hydrogen reciprocating compressors10.29354/diag/82961 ↗
22. Experimental study of pumps in a pipe bench10.1088/1742-6596/1257/1/012003 ↗
23. Liu, Y., Ma, X., Li, Y., Tie, Y., Zhang, Y., and Gao, J. (2019). Watwer Pipeline Leakage Detection Based on Machine Learning and Wireless Sensor Networks. Sensors, 19.10.3390/s19235086 ↗
24. Bielawski, P. Identification of the piston machine combustion chamber tightness. J. Qual. Maint. Eng., Submitted.
25. Pump efficiency improvement
26. Jeżowiecka-Kabsch, K., and Szewczyk, H. (2001). Fluid Mechanics, Oficyna Wydawnicza Politechniki Wrocławskiej. (in Polish).
27. Böswirth, L., and Bschorer, S. (2012). Technische Strömungslehre, Teubner Verlag. [9th ed.].10.1007/978-3-8348-8647-7 ↗
28. Mieszkowski, M. (1985). Positive Displacement Compressor Testing. Thermal and Energy Measurements, WNT. (in Polish).
29. Diagnosing of pipelines
30. Mieszkowski, M. (1985). Testing of ventilators. Thermal and Energy Measurements, WNT. (in Polish).
31. Mieszkowski, M. (1985). Testing of centrifugal pumps. Thermal and Energy Measurements, WNT. (in Polish).
32. (2005). PN-EN ISO 5167-1:2005 Measurement of Fluid Flow by Means of Pressure Differential Devices Inserted in Circular Cross-Section Conduits Running Full—Part 1: General Principles and Requirements, Polish Committee for Standardization.
33. (2005). PN-EN ISO 5167-2:2005 Measurement of Fluid Flow by Means of Pressure Differential Devices Inserted in Circular Cross-Section Conduits Running Full—Part 2: Orifice Plates, Polish Committee for Standardization.
34. Measurements of fluid flow lux pulsations (1)
35. Measurements of fluid flux pulsations (2). Constriction flowmeters
36. Manepatil, S.S., and Tiwari, A. (2006, January 17–20). Fault Diagnosis of Reciprocating Compressor Using Pressure Pulsations. Proceedings of the International Compressor Engineering Conference at Purdue, Lafayette, IN, USA. Available online: http://docs.lib.purdue.edu/icec/1819.
37. Diagnosing the wear margin of thermal nodes
38. Sperlich, V. (2007). Grundlagen der Technischen Thermodynamik, Universität Duisburg.
39. Domański, R., Jaworski, M., Rebow, M., and Kołtyś, J. (2000). Some Problems of Thermodynamics: Computer-Based Approach, Wydawnictwo Naukowe PWN. (in Polish).
40. Measures and symptoms of wear margin in functional unit nodes of production system items
41. Moeck, E., and Strickert, H. (1982). Technische Diagnostik an Schiffsmaschinenanlagen, Verlag Technik.
42. Thermodynamic method used for pump performance and efficiency testing program
43. Succar, S., and Williams, R.H. (2020, April 01). Compressed Air Energy Storage: Theory, Resources and Applications for Wind Power, Available online: https://www.nrc.gov/docs/ML1003/ML100361047.pdf,.
44. (2018). EN 13445-5:2018. Unfired Pressure Vessels—Part 5: Inspection and Testing, European Committee for Standardization.
45. Marczuk, M. (1973). Design and Operation of Hydrophore Devices, Arkady. [2nd ed.]. (in Polish).
46. Bańkowski, Z., Bernhardt, M., Chmielewski, H., Dobrzański, T., Gosztowtt, L., Hausman, K., Karaszkiewicz, A., Kosieradzki, P., Krotochwil, Z., and Kuczewski, S. (1984). Mechanic’s Little Manual, WNT. [15th ed.]. (in Polish).