journal article·2025-11-09Open access

Development of Two-Wrinkled Tubes Using an Electrostatic Structural Analysis

Samara C. R. Soares, Gilmar C. Silva, Elza M. M. Fonseca

Applied Sciences· Volume 15· Issue 22

Abstract

The primary aim of this study is to develop an axisymmetric numerical model, employing the finite element approach, to simulate a two-wrinkling tube in T6 aluminum. The method uses an electric potential applied to the tube mesh, which passes through a solid die to induce the wrinkling process, facilitated by contact elements between the tube and the die. A lateral incremental voltage electric potential (0–50 kV), due to an electric coil, and applied axial and compressive displacement (0–12 mm) was considered. The materials’ properties were established as nonlinear, with elastoplastic behavior. The results were analyzed, which allowed the tube deformation with two wrinkles, comparable with previous results.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Materials and Mechanics · Metal Forming Simulation Techniques · Electromagnetic Effects on Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Mechanical Engineering Department, Pontifícia Universidade Católica de Minas Gerais—PUC MINAS, Rua Dom José Gaspar, 500, Belo Horizonte 30535-901, MG, Brazil

Mechanical Engineering Department, School of Engineering, Polytechnic Institute of Porto, Rua Dr. António Bernardino de Almeida, 431, 4200-072 Porto, Portugal

Funding

Coordination for the Improvement of Higher Education Personnel-Brazil

References (37)

Show source-provided references
1. Li, H., Zhu, Y., Chen, W., Yuan, C., and Wang, L. (2025). Advanced Bending and Forming Technologies for Bimetallic Composite Pipes. Materials, 18.10.3390/ma18010111 ↗
2. Finite Element Analysis of Tube End Forming and Process Design10.4028/www.scientific.net/KEM.830.69 ↗
3. Nikhare, C.P. (2020). Fundamentals in Sheet and Tube Forming: Material Characterization, Conventional and Novel Processes and Involved Mechanics, Springer.10.1007/978-3-030-18854-2_1 ↗
4. Approach Based on Response-Surface Method to Optimize Lining of Dies Used in 3D Free-Bending Forming Technology10.1186/s10033-024-01096-4 ↗
5. Finite Electroelastic Deformation of Dielectric Semilinear Hyperelastic Tubes10.21741/9781644902592-35 ↗
6. Finite Deformations of an Electroelastic Circular Cylindrical Tube10.1007/s00033-016-0733-0 ↗
7. Simulation Analysis of Shell Aluminum Alloy Tube for Neck-In Spinning Process
8. Waves and Vibrations in a Finitely Deformed Electroelastic Circular Cylindrical Tube10.1098/rspa.2019.0701 ↗
9. Soares, S.C.R., Silva, G.C., and Fonseca, E.M.M. (2024). Computational Methodology for the Development of Wrinkled Tubes by Plastic Deformation. Appl. Sci., 14.10.3390/app142311126 ↗
10. A State-of-the-Art Review of Hydroforming Technology10.1007/s12289-019-01507-1 ↗
11. An Improved Two-Arcs Deformational Theoretical Model of the Expansion Tubes10.1016/j.ijmecsci.2017.08.036 ↗
12. Pipe Joining by Mechanical Conformation in Thin Sheets with Rotary Locking via a Notch10.1016/j.engstruct.2021.113151 ↗
13. Formability Assessment of Plastic Joining by Compression Instability for Thin-Walled Tubes10.1007/s00170-018-2128-1 ↗
14. Digital Twin of Tube Hydroforming Press and Process
15. Bhujangrao, T., Veiga, F., Penalva, M., Costas, A., and Ruiz, C. (2022). Three-Dimensional Finite Element Modelling of Sheet Metal Forming for the Manufacture of Pipe Components: Symmetry Considerations. Symmetry, 14.10.3390/sym14020228 ↗
16. Simonetto, E., Wang, Q., Ghiotti, A., and Bruschi, S. (2023). Forming Quality Indices for Tube Roll Forming: Definition and Modelling. Proceedings of the International Conference on Manufacturing, Springer.10.1007/978-3-031-41023-9_57 ↗
17. Research Overview on Rectangular Tube Cross-Section Deformation in Rotary-Draw Bending Process10.1088/1742-6596/2706/1/012069 ↗
18. Volgin, V.M., Kukhar, V.D., and Kireeva, A.E. (2018). Multiphysics Simulation of Electromagnetic Forming of Aluminum Alloy Tubes. Lecture Notes in Mechanical Engineering, Springer.10.1007/978-3-319-95630-5_199 ↗
19. Numerical Simulation and Experimental Study on Axial Compression Electromagnetic Bulging of Aluminum Alloy Tube10.1007/s00170-024-13997-8 ↗
20. Analytical and Experimental Study of Wrinkling in Electromagnetic Tube Compression10.1007/s00170-017-0571-z ↗
21. Electromagnetic Metal Forming10.1243/PIME_PROC_1965_180_013_02 ↗
22. Hosseini, S.V., Hatami, S., Darvizeh, A., and Chizari, M. (2021). Analytical Modelling of Electromagnetic Bulging of Thin Metallic Tubes. Recent Trends in Manufacturing and Materials Towards Industry 4.0, Springer.10.1007/978-981-15-9505-9_70 ↗
23. Pawar, S., Kore, S.D., and Nandy, A. (2021). Recent Advancement in Electromagnetic Forming Processes. Recent Advances in Manufacturing Processes, Springer.10.1007/978-981-15-7711-6_16 ↗
24. Pawar, S., Kore, S.D., and Nandy, A. (2019). Magnetic Pulse Forming and Punching of Al Tubes—A Novel Technique for Forming and Perforation of Tubes. Advances in Material Forming and Joining, Springer.10.1007/978-981-32-9417-2_5 ↗
25. A Flexible and Economical Method for Electromagnetic Flanging of Tubes with Field Shapers10.1007/s00170-021-07478-5 ↗
26. Flaring Forming of Small Tube Based on Electromagnetic Attraction10.1109/ACCESS.2020.2999125 ↗
27. Form-Fit Joining Behavior Between an Aluminium Tube and Sheet Using Electromagnetic Forming10.1088/1757-899X/418/1/012115 ↗
28. Study on Material Deformation Performance and Electromagnetic Force Loading in Electromagnetic Tube Expansion Process
29. Boutana, I., Mekideche, M.R., and Bali, H. (2023, January 20–23). Analysis Model and Numerical Investigation of Electromagnetic Tube Expansion with Field Concentrator. Proceedings of the 2023 International Conference on Systems, Signals and Devices, Mahdia, Tunisia.10.1109/SSD58187.2023.10411205 ↗
30. A Research Based on Advance Dual-Coil Electromagnetic Forming Method on Flanging of Small-Size Tubes10.1007/s00170-019-03498-4 ↗
31. Experimental Analysis of Interference-Fit Joining of Aluminum Tubes by Electromagnetic Forming10.1109/TASC.2020.2972499 ↗
32. ASM International (1990). Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, ASM International. ASM Handbook.
33. Davis, J.R. (1993). Aluminum and Aluminum Alloys, ASM International. ASM Specialty Handbook.
34. Marciniak, Z., Duncan, J.L., and Hu, J. (2002). Mechanics of Sheet Metal Forming, Butterworth-Heinemann. [2nd ed.].
35. Altan, T., and Tekkaya, A.E. (1983). Metal Forming: Fundamentals and Applications, ASM International.
36. Groover, M.P. (2015). Fundamentals of Modern Manufacturing: Materials, Processes, and Systems, Wiley. [6th ed.].
37. Finite Element Analysis to Predict Temperature Rise Tests in High-Capacity Substation Connectors10.1049/iet-gtd.2016.1717 ↗