Investigation of the effect of temper rolling on the texture evolution and mechanical behavior of IF steels using multiscale simulation
Source abstract
Abstract
The main objective of this study is to simulate texture and deformation during the temper-rolling process. To this end, a rate-independent crystal plasticity model, based on the self-consistent scale-transition scheme, is adopted to predict texture evolution and deformation heterogeneity during temper-rolling process. For computational efficiency, a decoupled analysis is considered between the polycrystalline plasticity model and the finite element analysis for the temper rolling. The elasto-plastic finite element analysis is first carried out to determine the history of velocity gradient during the numerical simulation of temper rolling. The thus calculated velocity gradient history is subsequently applied to the polycrystalline plasticity model. By following some appropriately selected strain paths (i.e., streamlines) along the rolling process, one can predict the texture evolution of the material at the half thickness of the sheet metal as well as other parameters related to its microstructure. The numerical results obtained by the proposed strategy are compared with experimental data in the case of IF steels.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Metallurgy and Material Forming · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (62)
Show source-provided references
1. Poortmans S, Duchêne L, Habraken AM, Verlinden B (2009) Modelling compression tests on aluminium produced by equal channel angular extrusion. Acta Mater 57:1821–183010.1016/j.actamat.2008.12.023 ↗
2. Gawad J, Van Bael A, Eyckens P, Samaey G, Van Houtte P, Roose D (2013) Hierarchical multi-scale modeling of texture induced plastic anisotropy in sheet forming. Comput Mater Sci 66:65–8310.1016/j.commatsci.2012.05.056 ↗
3. Van Houtte P, Gawad J, Eyckens P, Van Bael P, Samaey G, Roose D (2012) Multi-scale modelling of the development of heterogeneous distributions of stress, strain, deformation texture and anisotropy in sheet metal forming. Procedia IUTAM 3:67–7510.1016/j.piutam.2012.03.005 ↗
4. Van Houtte P, Kanjarla AK, Van Bael A, Seefeldt M, Delannay L (2006) Multiscale modelling of the plastic anisotropy and deformation texture of polycrystalline materials. Eur J Mech - A/Solids 25:634–64810.1016/j.euromechsol.2006.05.003 ↗
5. Tóth LS, Molinari A (1994) Tuning a self consistent viscoplastic model by finite element results—II. Application to torsion textures. Acta Metall Mater 42:2459–246610.1016/0956-7151(94)90325-5 ↗
6. Peirce D, Asaro RJ, Needleman A (1982) An analysis of nonuniform and localized deformation. Acta Metall 30:1087–111910.1016/0001-6160(82)90005-0 ↗
7. Roters F, Eisenlohr P, Hantcherli L, Tjahjanto DD, Bieler TR, Raabe D (2010) Overview of constitutive laws, kinematics, homogenization and multiscale methods in crystal plasticity finite-element modeling : Theory, experiments, applications. Acta Mater 58:1152–121110.1016/j.actamat.2009.10.058 ↗
8. Boudifa M, Saanouni K, Chaboche J (2009) A micromechanical model for inelastic ductile damage prediction in polycrystalline metals for metal forming. Int J Mech Sci 51:453–46410.1016/j.ijmecsci.2009.03.014 ↗
9. Zamiri AR, Pourboghrat F (2010) A novel yield function for single crystals based on combined constraints optimization. Int J Plast 26:731–74610.1016/j.ijplas.2009.10.004 ↗
10. Zamiri A, Pourboghrat F (2007) An effective computational algorithm for rate-independent crystal plasticity based on a single crystal yield surface with an application to tube hydroforming. Int J Plast 23:1126–114710.1016/j.ijplas.2006.10.012 ↗
11. Zhang H, Dong X, Wang Q, Zeng Z (2012) An effective semi-implicit integration scheme for rate dependent crystal plasticity using explicit finite element codes. Comput Mater Sci 54:208–21810.1016/j.commatsci.2011.10.011 ↗
12. Li HW, Yang H, Sun ZC (2008) A robust integration algorithm for implementing rate dependent crystal plasticity into explicit finite element method. Int J Plast 24:267–28810.1016/j.ijplas.2007.03.014 ↗
13. Li DY, Peng YH, Zhang SR, Liu SR (2009) Numerical simulation of sheet metal stamping by using ODF data. Int J Mech Sci 51:41–5110.1016/j.ijmecsci.2008.11.004 ↗
14. Guan Y, Pourboghrat F (2006) Finite element modeling of tube hydroforming of polycrystalline aluminum alloy extrusions. Int J Plast 22:2366–239310.1016/j.ijplas.2006.04.003 ↗
15. Segurado J, Lebensohn RA, Llorca J, Tomé CN (2012) Multiscale modeling of plasticity based on embedding the viscoplastic self-consistent formulation in implicit finite elements. Int J Plast 28:124–14010.1016/j.ijplas.2011.07.002 ↗
16. Mathur KK, Dawson PR (1989) On modeling the development of crystallographic texture in bulk forming processes. Int J Plast 5:67–9410.1016/0749-6419(89)90020-X ↗
17. Habraken AM, Duchêne L (2004) Anisotropic elasto-plastic finite element analysis using a stress–strain interpolation method based on a polycrystalline model. Int J Plast 20:1525–156010.1016/j.ijplas.2003.11.006 ↗
18. Peirce D, Asaro RJ, Needleman A, Park A (1983) Material rate dependence and localized deformation in crystalline solids. Acta Metall 31:1951–197610.1016/0001-6160(83)90014-7 ↗
19. Asaro RJ, Needleman A (1984) Texture development and strain hardening in rate dependent polycrystals. Acta Metall 33:923–95310.1016/0001-6160(85)90188-9 ↗
20. Kalidindi SR, Anand L (1992) An approximate procedure for predicting the evolution of crystallographic texture in bulk deformation processing of fcc metals. Int J Mech Sci 34:309–32910.1016/0020-7403(92)90038-I ↗
21. Jung K-H, Kim D-K, Im Y-T, Lee Y-S (2013) Prediction of the effects of hardening and texture heterogeneities by finite element analysis based on the Taylor model. Int J Plast 42:120–14010.1016/j.ijplas.2012.10.006 ↗
22. Franciosi P, Zaoui A (1991) Crystal hardening and the issue of uniqueness. Int J Plast 7:295–31110.1016/0749-6419(91)90037-Y ↗
23. Anand L, Kothari M (1996) A computational procedure for rate-independent crystal plasticity. J Mech Phys Solids 44:525–55810.1016/0022-5096(96)00001-4 ↗
24. Busso EP, Cailletaud G (2005) On the selection of active slip systems in crystal plasticity. Int J Plast 21:2212–223110.1016/j.ijplas.2005.03.019 ↗
25. Arul Kumar M, Mahesh S (2012) Banding in single crystals during plastic deformation. Int J Plast 36:15–3310.1016/j.ijplas.2012.03.008 ↗
26. Marin EB, Dawson PR (1998) Elastoplastic finite element analyses of metal deformations using polycrystal constitutive models. Comput Methods Appl Mech Eng 165:23–4110.1016/S0045-7825(98)00033-4 ↗
27. Jafarlou D, Hassan M, Mardi NA, Zalnezhad E (2014) Influence of Temper Rolling on Tensile Property of Low Carbon Steel Sheets by Application of Hill 48 Anisotropic Yield Criterion. Procedia Eng 81:1222–122710.1016/j.proeng.2014.10.101 ↗
28. Yoshida F, Kaneda Y, Yamamoto S (2008) A plasticity model describing yield-point phenomena of steels and its application to FE simulation of temper rolling. Int J Plast 24:1792–181810.1016/j.ijplas.2008.05.004 ↗
29. Roberts WL (1983) Cold Rolling of Steels. Marcel Dekker, New York10.1201/9781482276015 ↗
30. Lipinski P, Berveiller M (1989) Elastoplasticity of micro-inhomogeneous metals at large strains. Int J Plast 5:149–17210.1016/0749-6419(89)90027-2 ↗
31. Franz G, Abed-Meraim F, Lorrain J-P, Ben Zineb T, Lemoine X, Berveiller M (2009) Ellipticity loss analysis for tangent moduli deduced from a large strain elastic–plastic self-consistent model. Int J Plast 25:205–23810.1016/j.ijplas.2008.02.006 ↗
32. Franz G, Abed-meraim F, Berveiller M (2013) Strain localization analysis for single crystals and polycrystals : Towards microstructure-ductility linkage. Int J Plast 48:1–3310.1016/j.ijplas.2013.02.001 ↗
33. Iwakuma T, Nemat-Nasser S (1984) Finite elastic–plastic deformation of polycristalline metals. Proc R Soc L A 394:87–11910.1098/rspa.1984.0071 ↗
34. Lipinski P, Berveiller M, Reubrez E, Morreale J (1995) Transition theories of elastic–plastic deformation of metallic polycrystals. Arch Appl Mech 65:291–31110.1007/BF00789222 ↗
35. Berveiller M, Fassi-Fehri O, Hihi A (1987) The problem of two plastic and heterogeneous inclusions in an anisotropic medium. Int J Eng Sci 25:691–70910.1016/0020-7225(87)90058-9 ↗
36. Eshelby J (1957) The determination of the elastic field of an ellipsoidal inclusion and related problems. Proc R Soc L A 241:376–39610.1098/rspa.1957.0133 ↗
37. Hill R (1965) Continuum micro-mechanics of elastoplastic polycrystals. J Mech Phys Solids 13:89–10110.1016/0022-5096(65)90023-2 ↗
38. Nesterova E, Bacroix B, Teodosiu C (2001) Experimental observation of microstructure evolution under strain-path changes in low-carbon IF steel. Mater Sci Eng A 309–310:495–49910.1016/S0921-5093(00)01639-7 ↗
39. Bunge H (1969) Mathematische Methoden der Texturanalyse. Akademie-Verlag, Berlin
40. Bunge H (1982) Texture Analysis in Materials Science. Butterwort, London
41. François M, Sprauel J, Lebrun J (1991) Construction of a pseudo-material representation of a real textured material from ODF or direct pole figures. Textures Microstruct 14–18:169–17410.1155/TSM.14-18.169 ↗
42. Bachmann F, Hielscher R, Schaeben H (2010) Texture Analysis with MTEX – Free and Open Source Software Toolbox. Solid State Phenom 160:63–6810.4028/www.scientific.net/SSP.160.63 ↗
43. Hacquin A, Montmitonnet P, Guillerault J-P (1996) A steady state thermo-elastoviscoplastic finite element model of rolling with coupled thermo-elastic roll deformation. J Mater Process Technol 60:109–11610.1016/0924-0136(96)02315-1 ↗
44. Abdelkhalek S, Montmitonnet P, Legrand N, Buessler P (2008) Manifested flatness predictions in thin strip cold rolling. Int J Mater Form 1:339–34210.1007/s12289-008-0064-6 ↗
45. Abdelkhalek S, Zahrouni H, Potier-Ferry M, Legrand N, Montmitonnet P, Buessler P (2009) Coupled and uncoupled approaches for thin cold rolled strip buckling prediction. Int J Mater Form 2:833–83610.1007/s12289-009-0547-0 ↗
46. Nakhoul R, Montmitonnet P, Legrand N (2014) Manifested flatness defect prediction in cold rolling of thin strips. Int J Mater Form 8:283–29210.1007/s12289-014-1166-y ↗
47. Kang HG, Kim JK, Huh MY, Engler O (2007) A combined texture and FEM study of strain states during roll-cladding of five-ply stainless steel/aluminum composites. Mater Sci Eng A 452–453:347–35810.1016/j.msea.2006.10.130 ↗
48. Kim E-Y, Cho J, Kim H-W, Choi S-H (2011) Evolution of deformation texture in Al/Al–Mg/Al composite sheets during cold-roll cladding. Mater Sci Eng A 530:244–25210.1016/j.msea.2011.09.082 ↗
49. Decroos K, Sidor J, Seefeldt M (2013) A New Analytical Approach for the Velocity Field in Rolling Processes and Its Application in Through-Thickness Texture Prediction. Metall Mater Trans A 45:948–96110.1007/s11661-013-2021-3 ↗
50. Engler O, Huh MY, Tome CN (2000) A Study of Through-Thickness Texture Gradients in Rolled. Metall Mater Trans A 31:2299–231510.1007/s11661-000-0146-7 ↗
51. Lee CS, Duggan BJ (1991) A simple theory for the development of inhomogeneous rolling textures. Metall Trans A 22:2637–264310.1007/BF02851357 ↗
52. Nicaise N, Berbenni S, Wagner F, Berveiller M, Lemoine X (2011) Coupled effects of grain size distributions and crystallographic textures on the plastic behaviour of IF steels. Int J Plast 27:232–24910.1016/j.ijplas.2010.05.001 ↗
53. Van Houtte P, Li S, Seefeldt M, Delannay L (2005) Deformation texture prediction: from the Taylor model to the advanced Lamel model. Int J Plast 21:589–62410.1016/j.ijplas.2004.04.011 ↗
54. Bachu V, Kalidindi SR (1988) On the accuracy of the predictions of texture evolution by the finite element technique for fcc polycristals. Mater Sci Eng A 257:108–11710.1016/S0921-5093(98)00828-4 ↗
55. Franz G, Abed-Meraim F, Ben Zineb T, Lemoine X, Berveiller M (2009) Role of intragranular microstructure development in the macroscopic behavior of multiphase steels in the context of changing strain paths. Mater Sci Eng A 517:300–31110.1016/j.msea.2009.03.074 ↗
56. Franz G, Abed-Meraim F, Ben Zineb T, Lemoine X, Berveiller M (2011) Impact of intragranular microstructure development on ductility limits of multiphase steels. Mater Sci Eng A 528:3777–378510.1016/j.msea.2011.01.042 ↗
57. Kanjarla AK, Van Houtte P, Delannay L (2010) Assessment of plastic heterogeneity in grain interaction models using crystal plasticity finite element method. Int J Plast 26:1220–123310.1016/j.ijplas.2009.05.005 ↗
58. Peeters B (2002) Multiscale modelling of the induced plastic anisotropy in IF steel during sheet metal forming. Katholieke Universiteit Leuven
59. Peeters B, Seefeldt M, Teodosiu C, Kalidindi SR, Van Houtte P, Aernoudt E (2001) Work-hardening/softening behaviour of b.c.c. polycrystals during changing strain paths: I. An integrated model based on substructure and texture evolution, and its prediction of the stress–strain behaviour of an IF steel during two-stage strain paths. Acta Mater 49:1607–161910.1016/S1359-6454(01)00066-0 ↗
60. Peeters B, Bacroix B, Teodosiu C, Van Houtte P, Aernoudt E (2001) Work-hardening/softening behaviour of b.c.c. polycrystals during changing strain: II. TEM observations of dislocation sheets in an IF steel during two-stage strain paths and their representation in terms of dislocation densitiesActa Mater 49:1621–1632
61. Teodosiu C, Hu Z (1995) Evolution of the intragranular microstructure at moderate and large strains. In: Shen SF, Dawson PR (eds.) Proc. of Numiform’95, Simulation of Materials Processing: Theory, Methods and Applications, Balkema, Rotterdam, pp 173–182
62. Hiwatashi S, Van Bael A, Van Houtte P, Teodosiu C (1997) Modelling of plastic anisotropy based on texture and dislocation structure. Comput Mater Sci 9:274–28410.1016/S0927-0256(97)00069-4 ↗