Predicting flow localization in semi-solid deformation
Source abstract
Abstract
A new analytical instability criterion based on a finite deformation continuum analysis was developed to identify the condition associated with the unstable flow during the semi-solid deformation. The proposed criterion can be used to calculate the onset of strain localization. Strain localization causes the formation of liquid channels, which is the characteristic of an inhomogeneous deformation. The results indicate that strain localization increases with decreasing rate sensitivity and increases with increasing solid fraction. Considering the formability of alloys in the semi-solid state, the critical value of the solid fraction was determined according to the critical value of the localization parameter. The results obtained are in favorable agreement with the results from the experimental data for AA7075 and AA2014 aluminum alloy.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Metallurgy and Material Forming · Metallurgical Processes and Thermodynamics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. Atkinson HV, Burke K, Vaneetveld G (2008) Recrystallisation in the semi-solid state in 7075 aluminium alloy. Int J Mater Form 1:973–976. doi: 10.1007/s12289-008-0220-z10.1007/s12289-008-0220-z ↗
2. Bayoumi MA, Negm MI, El-Gohry AM (2009) Microstructure and mechanical properties of extruded Al–Si alloy (A356) in the semi-solid state. Mater Des 30:4469–4477. doi: 10.1016/j.matdes.2008.11.02510.1016/j.matdes.2008.11.025 ↗
3. Baadjou R, Knauf F, Hirt G (2009) Semi-solid forging and joining of steel components and their properties. Int J Mater Form 2:741–744. doi: 10.1007/s12289-009-0510-010.1007/s12289-009-0510-0 ↗
4. Rogal Ł, Dutkiewicz J, Atkinson HV et al (2013) Characterization of semi-solid processing of aluminium alloy 7075 with Sc and Zr additions. Mater Sci Eng A 580:362–373. doi: 10.1016/j.msea.2013.04.07810.1016/j.msea.2013.04.078 ↗
5. Chen Y, Zhang L, Liu W et al (2016) Preparation of Mg–Nd–Zn–(Zr) alloys semisolid slurry by electromagnetic stirring. Mater Des 95:398–409. doi: 10.1016/j.matdes.2016.01.13110.1016/j.matdes.2016.01.131 ↗
6. Chen G, Lin F, Yao S et al (2016) Constitutive behavior of aluminum alloy in a wide temperature range from warm to semi-solid regions. J Alloys Compd 674:26–36. doi: 10.1016/j.jallcom.2016.02.25410.1016/j.jallcom.2016.02.254 ↗
7. Koeune R, Ponthot J-P (2008) A one-phase thermomechanical constitutive model for the numerical simulation of semi-solid thixoforming. Int J Mater Form 1:1007–1010. doi: 10.1007/s12289-008-0228-410.1007/s12289-008-0228-4 ↗
8. Koeune R, Ponthot JP (2014) A one phase thermomechanical model for the numerical simulation of semi-solid material behavior. Application to thixoforming. Int J Plast 58:120–153. doi: 10.1016/j.ijplas.2014.01.00410.1016/j.ijplas.2014.01.004 ↗
9. Spencer DB, Mehrabian R, Flemings MC (1972) Rheological behavior of Sn-15 pct Pb in the crystallization range. Metall Trans 3:1925–1932. doi: 10.1007/BF0264258010.1007/BF02642580 ↗
10. Tzimas E, Zavaliangos A (2000) Evolution of near-equiaxed microstructure in the semisolid state. Mater Sci Eng A 289:228–240. doi: 10.1016/S0921-5093(00)00908-410.1016/S0921-5093(00)00908-4 ↗
11. Atkinson HV (2005) Modelling the semisolid processing of metallic alloys. Prog Mater Sci 50:341–412. doi: 10.1016/j.pmatsci.2004.04.00310.1016/j.pmatsci.2004.04.003 ↗
12. Liu TY, Atkinson HV, Kapranos P et al (2003) Rapid compression of aluminum alloys and its relationship to thixoformability. Metall Mater Trans A 34:1545–1554. doi: 10.1007/s11661-003-0266-y10.1007/s11661-003-0266-y ↗
13. Rudnicki JW, Rice JR (1975) Conditions for the localization of deformation in pressure-sensitive dilatant materials. J Mech Phys Solids 23:371–394. doi: 10.1016/0022-5096(75)90001-010.1016/0022-5096(75)90001-0 ↗
14. Kareh KM, Lee PD, Atwood RC et al (2014) Revealing the micromechanisms behind semi-solid metal deformation with time-resolved X-ray tomography. Nat Commun 5:1–710.1038/ncomms5464 ↗
15. Cai B, Karagadde S, Yuan L et al (2014) In situ synchrotron tomographic quantification of granular and intragranular deformation during semi-solid compression of an equiaxed dendritic Al–Cu alloy. Acta Mater 76:371–380. doi: 10.1016/j.actamat.2014.05.03510.1016/j.actamat.2014.05.035 ↗
16. Cai B, Lee PD, Karagadde S et al (2016) Time-resolved synchrotron tomographic quantification of deformation during indentation of an equiaxed semi-solid granular alloy. Acta Mater 105:338–346. doi: 10.1016/j.actamat.2015.11.02810.1016/j.actamat.2015.11.028 ↗
17. Gourlay CM, Meylan B, Dahle AK (2008) Shear mechanisms at 0–50% solid during equiaxed dendritic solidification of an AZ91 magnesium alloy. Acta Mater 56:3403–3413. doi: 10.1016/j.actamat.2008.03.02010.1016/j.actamat.2008.03.020 ↗
18. Meylan B, Terzi S, Gourlay CM et al (2010) Development of shear bands during deformation of partially solid alloys. Scr Mater 63:1185–1188. doi: 10.1016/j.scriptamat.2010.08.03210.1016/j.scriptamat.2010.08.032 ↗
19. DE Freitas ER, Ferrante M (2001) Rheological behaviour and deformation characteristics of a commercial and a laboratory-cast Al-4%Cu alloy in the semi-solid state. Acta Mater 49:3839–3847. doi: 10.1016/S1359-6454(01)00239-710.1016/S1359-6454(01)00239-7 ↗
20. Tzimas E, Zavaliangos A (1999) Mechanical behavior of alloys with equiaxed microstructure in the semisolid state at high solid content. Acta Mater 47:517–528. doi: 10.1016/S1359-6454(98)00356-510.1016/S1359-6454(98)00356-5 ↗
21. Gourlay CM, Dahle AK (2007) Dilatant shear bands in solidifying metals. Nature 445:70–7310.1038/nature05426 ↗
22. Suery M, Flemings MC (1982) Effect of strain rate on deformation behavior of semi-solid dendritic alloys. Metall Trans A 13:1809–1819. doi: 10.1007/BF0264783710.1007/BF02647837 ↗
23. Zavaliangos A (1998) Modeling of the mechanical behavior of semisolid metallic alloys at high volume fractions of solid. Int J Mech Sci 40:1029–1041. doi: 10.1016/S0020-7403(98)00011-310.1016/S0020-7403(98)00011-3 ↗
24. Ziegler H (1963) Some extremum principles in irreversible thermodynamics with application to continuum mechanics. Prog Solids Mech 4:93–193
25. Rajagopal K, Srinivasa AR (1998) Mechanics of the inelastic behavior of materials—part 1, theoretical underpinnings. Int J Plast 14:945–967. doi: 10.1016/S0749-6419(98)00037-010.1016/S0749-6419(98)00037-0 ↗
26. Rajagopal K, Srinivasa AR (1998) Mechanics of the inelastic behavior of materials. Part II: inelastic response. Int J Plast 14:969–995. doi: 10.1016/S0749-6419(98)00041-210.1016/S0749-6419(98)00041-2 ↗
27. Srinivasa AR (2010) Application of the maximum rate of dissipation criterion to dilatant, pressure dependent plasticity models. Int J Eng Sci 48:1590–1603. doi: 10.1016/j.ijengsci.2010.09.01010.1016/j.ijengsci.2010.09.010 ↗
28. Semiatin SL, Lahoti GD (1981) Deformation and unstable flow in hot forging of Ti-6Ai-2Sn-4Zr-2Mo-0.1Si. Metall Trans A 12:1705–1717. doi: 10.1007/BF0264375310.1007/BF02643753 ↗
29. Jonas JJ, Holt RA, Coleman CE (1976) Plastic stability in tension and compression. Acta Metall 24:911–918. doi: 10.1016/0001-6160(76)90039-010.1016/0001-6160(76)90039-0 ↗
30. Pan J, Saje M, Needleman A (1983) Localization of deformation in rate sensitive porous plastic solids. Int J Fract 21:261–278. doi: 10.1007/BF0094234510.1007/BF00942345 ↗
31. Xu X-P, Needleman A (1992) The influence of nucleation criterion on shear localization in rate-sensitive porous plastic solids. Int J Plast 8:315–330. doi: 10.1016/0749-6419(92)90052-E10.1016/0749-6419(92)90052-E ↗
32. Binesh B, Aghaie-Khafri M (2015) Microstructure and texture characterization of 7075 Al alloy during the SIMA process. Mater Charact 106:390–403. doi: 10.1016/j.matchar.2015.06.01310.1016/j.matchar.2015.06.013 ↗