journal article·2004-12

Effect of biaxial loads on elastic-plastic J and crack tip constraint for cracked plates: finite element study

Yun-jae Kim, Ki-hyun Chung, Jin-su Kim, Young-jin Kim

International Journal of Fracture· Volume 130· Issue 4
Publisher page

Abstract

Based on detailed two-dimensional (2-D) and three-dimensional (3-D) finite element (FE) analyses, this paper attempts to quantify in-plane and out-of-plane constraint effects on elastic-plastic J and crack tip stresses for a plate with a through-thickness crack and semi-elliptical surface crack under positive biaxial loading. For the plate with a through-thickness crack, plate thickness and relative crack length are systematically varied, whereas for the plate with a semi-elliptical surface crack, the relative crack depth and aspect ratio of the semi-elliptical crack are systematically varied. It is found that the reference stress based approach for uniaxial loading can be applied to estimate J under biaxial loading, provided that the limit load specific to biaxial loading is used, implying that quantification of the biaxiality effect on the limit load is important. Investigation on the effect of biaxiality on the limit load suggests that for relatively thin plates with small cracks, in particular with semi-elliptical surface cracks, the effect of biaxiality on the limit load can be neglected for positive biaxial loading, and thus elastic-plastic J for a biaxially loaded plate could be estimated, assuming that such plate is subject to uniaxial load. Regarding the effect of biaxiality on crack tip stress triaxiality, it is found that such effect is more pronounced for a thicker plate. For plates with semi-elliptical surface cracks, the crack aspect ratio is found to be more important than the relative crack depth, and the effect of biaxiality on crack tip stress triaxiality is found to be more pronounced near the surface points along the crack front.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fatigue and fracture mechanics · Structural Integrity and Reliability Analysis · Structural Load-Bearing Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. ABAQUS (1999). ABAQUS Version 5.8. User's Manual, Hibbitt, Karlsson & Sorensen, Inc, 1999.
2. Ainsworth, R.A. (1984). The assessment of defects in structures of strain hardening materials. Engineering Fracture Mechanics 19, 633?42.10.1016/0013-7944(84)90096-1 ↗
3. Anderson, T.L. (1995). Fracture Mechanics: Fundamentals and Applications, CRC Press.
4. ASTM (1996). ASTM Standard, E 1820-96.Standard Test Method for Measurement of Fracture Toughness. Annual Book of ASTM Standards, Section 3, vol. 03.01, pp.981?1013.
5. Betegon, C. and Hancock, J.W. (1991). Two parameter characterisation of elastic-plastic crack tip fields. Journal of Applied Mechanics 58, 104?110.10.1115/1.2897135 ↗
6. Brocks, W. and Schmit, W. (1995). The second parameter in J?R curves: constraint or triaxiality. Constraint Effects in Fracture?Theory and Applications, ASTM STP 1244 (Edited by M. Kirk and A. Bakker) American Society for Testing and Materials, Philadelphia, 209?231.
7. Brocks, W., Kunecke, G.and Wobst, K. (1989). Stable crack growth of axial surface flaws in pressure vessels. International Journal of Pressure Vessels and Piping 40, 77?90.10.1016/0308-0161(89)90125-7 ↗
8. Dalle Donne, C. (1999). The crack tip displacement vector approach to mixed mode fracture. Mixed-Mode Crack Behaviour, ASTM 1359 (Edited by K.J. Miller and D.L. McDowell), American Society for Testing and Materials, West Conshohocken, PA, pp.21?40.
9. Dalle Donne, C. and Doker, H. (1994). Biaxial load effects on plane stress J-?a and ?5-?a curves. Structural Integrity, Experiments-Models-Applications, (Edited by C. Berger and K.H. Schwalbe), Proceedings of ECF 10, Vol. II, pp.891?896.
10. Dowling, N.E. (1987). J-integral estimates for cracks in infinite bodies. Engineering Fracture Mechanics 26, 333?348.10.1016/0013-7944(87)90016-6 ↗
11. Hancock, J.W., Reuter, W.G. and Parks, D.M. (1993). Constraint and toughness parameterised by T. Constraint Effect in Fracture, ASTM STP 1171 (Edited by E.M. Hackett, K.H. Schwalbe, and R.H. Dodds), American Society for Testing and Materials, Philadelphia, pp.21?40.
12. Hutchinson, J.W. (1968). Singular behaviour at the end of a tensile crack tip in a hardening material. Journal of the Mechanics and Physics of Solids 16, 13?31.10.1016/0022-5096(68)90014-8 ↗
13. Jansson, S. (1986). Fully plastic plane stress solutions for biaxially loaded centre-cracked plates. Journal of Applied Mechanics 53, 555?560.10.1115/1.3171810 ↗
14. Joyce, J.A., Hackett, E.M. and Roe, C. (1993). Effects of crack depth and mode of loading on the JR curve behaviour of a high-strength steel. Constraint Effect in Fracture, ASTM STP 1171 (Edited by E.M. Hackett, K.H. Schwalbe and R.H. Dodds), American Society for Testing and Materials, Philadelphia, pp.239?263.
15. Kim, Y.J. (2002). Estimation of fully plastic crack tip stresses from equilibrium of least upper bound circular arcs. International Journal of Mechanical Science 44, 881?897.10.1016/S0020-7403(02)00032-2 ↗
16. Kim, Y.J., Kim, J.S., Shim, D.J. and Kim, Y.J. (2004). Applicability of reference stress based J estimates to semi-elliptical surface crack problems. Journal of Strain Analysis 39, 245?260.10.1243/030932404323042678 ↗
17. Kumar, V. (1982). Estimation Technique for the Prediction of Elastic-Plastic Fracture of Structural Components of Nuclear Systems. 5th and 6th Semi-annual Reports to EPRI.
18. Kumar, V. and German, M.D. (1988). Elastic-Plastic Fracture Analysis of Through-Wall and Surface Flaws in Cylinders. EPRI Report NP-5596.
19. Kumar, V., German, M.D. and Shih, C.F. (1981). An Engineering Approach for Elastic-Plastic Fracture Analysis. EPRI Final Report NP-1931.10.2172/6068291 ↗
20. Lee, J.D. and Liebowitz, H. (1977). Fracture criteria for crack growth under biaxial loading. Engineering Fracture Mechanics 9, 765?779.10.1016/0013-7944(77)90002-9 ↗
21. Link, R.E. and Joyce, J.A. (1995). Experimental investigation of fracture toughness scaling models. Constraint Effect in Fracture, ASTM STP 1244 (Edited by M. Kirk and A.D. Bakker), American Society for Testing and Materials, Philadelphia, pp.286?315.
22. Margolin, B.Z. and Kostylev, V.I. (1998). Analysis of biaxial loading effect on fracture toughness of reactor pressure vessel steels. International Journal of Pressure Vessels and Piping 75, 589?601.10.1016/S0308-0161(98)00056-8 ↗
23. McClintock, F.A. (1971). Plasticity aspects of fracture, In Fracture: An Advanced Treatise. vol. 3. Academic Press, New York, pp. 47?225.
24. Miller, A.G. (1988). Review of limit loads of structures containing defects. International Journal of Pressure Vessels and Piping 32, 191?327.10.1016/0308-0161(88)90073-7 ↗
25. O'Dowd, N.P. and Shih, C.F. (1991). Family of crack-tip fields characterised by a triaxiality parameter. Journal of the Mechanics and Physics of Solids 39, 898?1015.10.1016/0022-5096(91)90049-T ↗
26. O'Dowd, N.P., Kolednik, O. and Naumenko, V.P. (1999), Elastic-plastic analysis of biaxially loaded centre-cracked plates, International Journal of Solids and Structures 36, 5639?5661.10.1016/S0020-7683(98)00257-1 ↗
27. Raju, I.S. and Newman Jr., J.C. (1979). Stress intensity factors for a wide range of semi-elliptical surface cracks in finite-thickness plates. Engineering Fracture Mechanics 11, 817?829.10.1016/0013-7944(79)90139-5 ↗
28. Rice, J.R. and Rosengren, G.F. (1968). Plane strain deformation near a crack tip in a power-law hardening material. Journal of the Mechanics and Physics of Solids 16, 1?12.10.1016/0022-5096(68)90013-6 ↗
29. Rice, J.R. and Tracey, D.M. (1969). On the ductile enlargement of voids in triaxial stress fields. Journal of the Mechanics and Physics of Solids 17, 201?217.10.1016/0022-5096(69)90033-7 ↗
30. R6 (2001). R6: Assessment of the Integrity of Structures Containing Defects, Revision 4, Amendment 10. British Energy.
31. Roos, E., Eisele, U. and Silcher, H. (1993). Effect of stress state on the ductile fracture behaviour of large-scale specimens. Constraint Effect in Fracture, ASTM STP 1171 (Edited by E.M. Hackett, K.H. Schwalbe, and R.H. Dodds), American Society for Testing and Materials, Philadelphia, 41?63.
32. Theiss, T.J., Shum, D.K. and Rolfe, S.T. (1992). Experimental and Analytical Investigation of the Shallow-Flaw Effect in Reactor Pressure Vessel. NUREG/CR-5886, USNRC.
33. Yuan, H. and Brocks, W. (1998). Quantification of constraint effects in elastic-plastic crack front fields. Journal of the Mechanics and Physics of Solids 46, 219?241.10.1016/S0022-5096(97)00068-9 ↗
34. Zahoor, A. (1991). Ductile Fracture Handbook. Novetech Corp.