Robust Design of 3D-Printed 6–18 GHz Double-Ridged TEM Horn Antenna
Source abstract
Abstract
A robust design of a 3D-printed 6–18 GHz double-ridged TEM horn antenna is proposed in this paper. The designed TEM horn antenna has two parts: an adaptor and a horn aperture. The adaptor is realized using a double-ridged waveguide to extend the operating bandwidth of the dominant mode (TE10 mode). Meanwhile, the horn aperture section is implemented in an exponentially tapered configuration to match the impedance of the double-ridged waveguide with the intrinsic impedance. The performance of the initially designed antenna shows that the reflection coefficient and gain levels are less than −13 dB and greater than 5.5 dBi within the 6–18 GHz band, respectively. The initial design was well done, but the noise factors that may occur during the manufacturing process were not taken into account. To design an antenna considering these noise factors, the parameters of the initial design are optimized by a novel robust design method also proposed in this paper. The robustness of the antenna optimized by the proposed method is approximately 12.4% higher than that of the initial antenna. The validity of the proposed method was tested by fabricating the antenna. A prototype of the optimized antenna with the proposed robust design method is fabricated using a 3D printer with a stereolithographic apparatus attached, and the surface of the frame is covered by a nano-silver plating. The measured results of the fabricated antenna are in good agreement with the simulation results over the operating band. The measured −10 dB reflection coefficient bandwidth of the antenna can cover 6–18 GHz. In addition, the measured gain ranges from 4.42 to 10.75 dBi within the 6–18 GHz band.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Antenna Design and Analysis · Microwave Engineering and Waveguides · Advanced Antenna and Metasurface Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Electrical and Computer Engineering, Sungkyunkwan University, Suwon 440-746, Korea
Department of Electronics and Computer Engineering, Hanyang University, Seoul 133-971, Korea
Funding
National Research Foundation of Korea
References (20)
Show source-provided references
1. Analysis and simulation of a 1–18-GHz broadband double-ridged horn antenna10.1109/TEMC.2002.808022 ↗
2. A lightweight waveguide horn antenna made via 3D printing and conductive spray coating10.1002/mop.30374 ↗
3. Creating a gain enhancement technique for a conical horn antenna by adding a wire medium structure at the aperture10.5515/JKIEES.2016.16.2.134 ↗
4. Investigation of 3D printed electrically small folded spherical meander wire antenna10.26866/jees.2017.17.4.228 ↗
5. Realistic head phantom for evaluation of brain stroke localization methods using 3D printer10.5515/JKIEES.2016.16.4.254 ↗
6. 3D printed dielectric reflectarrays: Low-cost high-gain antennas at sub-millimeter waves10.1109/TAP.2014.2303195 ↗
7. Wideband and UWB antennas for wireless applications: A comprehensive review10.1155/2017/2390808 ↗
8. Wu, Y., Isakov, D., and Grant, P.S. (2017). Fabrication of composite filaments with high dielectric permittivity for fused deposition 3D printing. Materials, 10.10.3390/ma10101218 ↗
9. 3-D printed metal-pipe rectangular waveguides10.1109/TCPMT.2015.2462130 ↗
10. Linear antenna array synthesis using Taguchi’s method: A novel optimization technique in electromagnetics10.1109/TAP.2007.891548 ↗
11. Küçük, Ö., Elfarah, T.T.K., Islak, S., and Özorak, C. (2017). Optimization by using Taguchi method of the production of magnesium-matrix carbide reinforced composites by powder metallurgy method. Metals, 7.10.3390/met7090352 ↗
12. Chen, H.-J., Chang, S.-N., and Tang, C.-W. (2017). Application of the Taguchi method for optimizing the process parameters of producing lightweight aggregates by incorporating tile grinding sludge with reservoir sediments. Materials, 10.10.3390/ma10111294 ↗
13. Schneider, C.F., Lisboa, C.P., Silva, R.A., and Lermen, R.T. (2017). Optimizing the parameters of TIG-MIG/MAG hybrid welding on the geometry of bead welding using the Taguchi method. J. Manuf. Mater. Process., 1.10.3390/jmmp1020014 ↗
14. Robust design of dual band/polarization patch antenna using sensitivity analysis and Taguchi’s method10.1109/TMAG.2010.2081663 ↗
15. A practical approach to robust design of a RFID triple-band PIFA structure10.1109/TMAG.2010.2045748 ↗
16. Genetical swarm optimization: An evolutionary algorithm for antenna design
17. Calculation of the parameters of ridge waveguides10.1109/TMTT.1957.1125084 ↗
18. The design of ridged waveguides10.1109/TMTT.1955.1124972 ↗
19. Pozar, D.M. (1998). Microwave Engineering, Wiley. [2nd ed.].
20. Effects of extreme surface roughness on 3D printed horn antenna10.1049/el.2013.1528 ↗