Thermal and Electrical Performance Analysis of Molded Metal-Filled Polymer Composites in Pouch-Type Battery Modules
Source abstract
Abstract
In this study, the thermal and structural behavior of battery module components produced from polymer-based composites was systematically evaluated using coupled Moldflow 2016 and ANSYS Fluent 2024 simulations. Three thermoplastics—metal-flake-reinforced PC+ABS (Polycarbonate/Acrylonitrile Butadiene Styrene), carbon-fiber-reinforced PEEK (Polyether Ether Ketone), and hybrid mineral-filled PP (Polypropylene)—were investigated as alternatives to conventional aluminum components. Moldflow simulations enabled the assessment of injection molding performance by determining injection pressure, volumetric shrinkage, warpage, residual stress, flow front temperature, and part weight. PEEK exhibited the best dimensional stability, with minimal warpage and shrinkage, while PP showed significant thermomechanical distortion, indicating poor resistance to thermally induced deformation. For thermal management, steady-state simulations were performed on a 1P3S pouch cell battery configuration using the NTGK/DCIR model under a constant heat load of 190 W. Material properties, including temperature-dependent thermal conductivity, density, and specific heat capacity, were defined based on validated databases. The results revealed that temperature distribution and Joule heat generation were strongly influenced by thermal conductivity. While aluminum exhibited the most favorable thermal dissipation, PC+ABS closely matched its electrical performance, with only a 1.3% lower average current magnitude. In contrast, PEEK and PP generated higher cell core temperatures (up to 20 K) due to limited heat conduction, although they had comparable current magnitudes imposed by the energy-conserving model. Overall, the findings indicate that reinforced thermoplastics, particularly PC+ABS, can serve as lightweight and cost-effective alternatives to aluminum in mid-range battery modules, providing similar electrical performance and thermal losses within acceptable limits.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Thermal properties of materials · Advanced Battery Technologies Research · Fiber-reinforced polymer composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Engineering, Balikesir University, 10145 Balikesir, Turkey
References (51)
Show source-provided references
1. Garud, K.S., Tai, L.D., Hwang, S.G., Nguyen, N.H., and Lee, M.Y. (2023). A review of advanced cooling strategies for battery thermal management systems in electric vehicles. Symmetry, 15.10.3390/sym15071322 ↗
2. Tarannum, F., Danayat, S., Nayal, A., Muthaiah, R., Annam, R.S., and Garg, J. (2022). Thermally expanded graphite polyetherimide composite with superior electrical and thermal conductivity. Polym. Adv. Technol., 1–28.10.1016/j.matchemphys.2023.127404 ↗
3. Graphene-enhanced hybrid phase change materials for thermal management of Li-ion batteries10.1016/j.jpowsour.2013.08.135 ↗
4. Azzopardi, B., Habib, A., Kaleg, S., Onggo, D., and Budiman, A.C. (2023). Recent advances in battery pack polymer composites. Energies, 16.10.3390/en16176223 ↗
5. Tan, J., and Zhang, Y. (2024). Thermal conductive polymer composites: Recent progress and applications. Molecules, 29.10.3390/molecules29153572 ↗
6. Simulation of injection-compression molding for thin and large battery housing10.1016/j.cap.2018.08.017 ↗
7. Baum, M., Anders, D., and Reinicke, T. (2023). Approaches for numerical modeling and simulation of the filling phase in injection molding: A review. Polymers, 15.10.3390/polym15214220 ↗
8. Towards an ultimate battery thermal management system: A review10.3390/batteries3010009 ↗
9. A comprehensive review of thermal management methods and ideal system design for improved electric vehicle battery pack performance and safety10.1002/ese3.2081 ↗
10. Reghunath, U., Gudi, A., and Bonala, S. (2023). Numerical modeling and simulation to predict thermal runaway propagation in an EV battery pack. SAE Tech. Pap., 1–759.10.4271/2023-01-0759 ↗
11. Pejman, R., Gorman, J., and Najafi, A.R. (2022). Multi-physics design of a new battery packaging for electric vehicles utilizing multifunctional composites. Compos. B Eng., 237.10.1016/j.compositesb.2022.109810 ↗
12. He, J., Wang, C., and Huang, Y. (2025). Thermal management and performance optimization in high-power-density lithium-ion battery modules. Energies, 18.10.3390/en18092294 ↗
13. Analysis of shrinkage and warpage in an injection-molded part with a thin shell feature using the response surface methodology10.1007/s00170-006-0739-4 ↗
14. A 3D study on the effect of gate location on the cooling of polymer by injection molding10.1016/j.ijheatfluidflow.2009.06.005 ↗
15. Piccirillo, F., Scognamiglio, F., Lasiello, M., and Chiu, W.K.S. (2025). Electro-thermal model of a pouch cell battery considering thermal runaway. J. Phys. Conf. Ser., 2940.10.1088/1742-6596/2940/1/012005 ↗
16. Study on experimental analysis and simulation model of thermal runaway phenomenon in pouch-type batteries for electric vehicles10.1007/s42791-025-00105-4 ↗
17. Wakale, A., Ma, S., and Hu, X. (2025). A thermal behaviour of battery cell using different electrochemical models (ECM and NTGK). SAE Tech. Pap.10.4271/2025-01-8140 ↗
18. Thermal expansion of metal-matrix composites10.1016/0266-3538(94)90122-8 ↗
19. Shang, S., and Wang, F. (2021). Role of residual thermal stress on the electrochemical performance of a solid-state half-cell. J. Appl. Phys., 130.10.1063/5.0071024 ↗
20. Amrit, A., Bahl, M., and Ranga, S. (2022). Multi-objective design optimization of EV battery tray. Recent Trends in Product Design and Intelligent Manufacturing Systems, Springer.10.1007/978-981-19-4606-6_75 ↗
21. Xu, L., Wang, S., Xi, L., Li, Y., and Gao, J. (2024). A review of thermal management and heat transfer of lithium-ion batteries. Energies, 17.10.3390/en17163873 ↗
22. dos Anjos, E.G.R., Marini, J., Montagna, L., Montanheiro, T., and Passador, F. (2020). Reactive processing of maleic anhydride-grafted ABS and its compatibilizing effect on PC/ABS blends. Polímeros, 30.10.1590/0104-1428.09220 ↗
23. Recent Advances in Organic Polymer Thermoelectric Composites10.1039/C6TC05488A ↗
24. Study on Electrochemical and Thermal Characteristics of Lithium-Ion Battery Using the Electrochemical–Thermal Coupled Model10.1002/er.4410 ↗
25. Parmar, M., Patel, D., Patel, V., and Patel, R. (2021). Thermal simulation of Li-ion battery pack using ANSYS Fluent. Recent Advances in Mechanical Infrastructure, Springer.10.1007/978-981-33-4176-0_22 ↗
26. Kim, D., Koh, J., Choi, E., and Kim, H.K. (2025). Cooling performance analysis of battery modules considering the viscoelastic behavior of thermal interface materials. Int. J. Automot. Technol.10.1007/s12239-025-00310-z ↗
27. Yu, Z., Sun, Z., Chang, L., Ma, C., Li, C., Li, H., Luan, C., and Al-Saidi, M.Y.M. (2023). Impact of multiple module collectors on the cell current distribution within the battery pack. Batteries, 9.10.3390/batteries9100501 ↗
28. Tan, Y., Li, Y., Gu, Y., Liu, W., Fang, J., and Pan, C. (2023). Numerical study on heat generation characteristics of charge and discharge cycle of the lithium-ion battery. Energies, 17.10.3390/en17010178 ↗
29. Optimization of injection molding process by using different types of conformal cooling channels10.52711/2321-581X.2022.00006 ↗
30. Ling, C., Wang, L., Kan, C.D., and Yang, C. (2024). Thermal-electrical-mechanical coupled finite element models for battery electric vehicle. Machines, 12.10.20944/preprints202407.0697.v1 ↗
31. A study on the battery case injection molding by CAE analysis
32. Optimization of the injection molding process for the PC/ABS parts by integrating Taguchi approach and CAE simulation10.1007/s00170-019-04283-z ↗
33. Influence of mineral filler on the thermal conductivity of polymer composites10.15587/2706-5448.2024.317659 ↗
34. Calculating the thermomechanical behaviour of plastic–metal hybrid components
35. Effect of filler and cooling rate on the glass transition of polymers
36. The effect of cooling rate on resistance-welded CF/PEEK joints10.1016/j.jmrt.2021.02.071 ↗
37. A review on conductive polymer composites focusing on advancements in electrical conductivity, and electromagnetic shielding capabilities
38. Investigation of the efficiency of conformal cooling channels of composite molds
39. Gámez, J.L., Vilaplana, A.J., Peydro, M.A., Selles, M.A., and Caballero, S.S. (2025). Predictive ANN modeling and optimization of injection molding parameters to minimize warpage in polypropylene rectangular parts. J. Manuf. Mater. Process., 9.10.3390/jmmp9070236 ↗
40. Composites in battery casing and energy storage
41. Develop a hybrid thermal simulation method for EV motor performance analysis, optim. and select cooling technology10.47392/IRJAEH.2024.0364 ↗
42. Comparative material selection of battery pack casing for an electric vehicle
43. The influence of graphite filler on the viscoelastic and mechanical characteristics of PC/ABS hybrid composite for automotive applications10.24191/jmeche.v21i1.25364 ↗
44. Injection molding of metal and carbon composites10.2497/jjspm.15D-SIS5-01 ↗
45. Molding of polyether ether ketone (PEEK) and its composites: A review
46. Influence of filler type and content on thermal conductivity and mechanical properties of thermoplastic compounds10.1002/pen.26266 ↗
47. Guerreiro, M., Rompante, J., Leite, A.C., Fernandes, L.P., Santos, R.M., Paiva, M.C., and Covas, J.A. (2021). Development of electrically conductive polymer nanocomposites for the automotive cable industry. Polímeros, 31.10.1590/0104-1428.20210017 ↗
48. Thermal performance enhancement of a passive battery thermal management system based on phase change material using cold air passageways for lithium batteries10.1016/j.est.2023.107744 ↗
49. Li, Y., Zhou, Z., and Wu, W.T. (2020). Three-dimensional thermal modeling of internal shorting process in a 20 Ah lithium-ion polymer battery. Energies, 13.10.3390/en13041013 ↗
50. Yu, Y., Zhang, J., Zhu, M., and Luyao, Z. (2023). Experimental Investigation on the Thermal Management for Lithium-Ion Batteries Based on the Novel Flame Retardant Composite Phase Change Materials. Batteries, 9.10.3390/batteries9070378 ↗
51. A Hybrid Thermal Management System for Lithium-Ion Batteries Combining Phase Change Materials with Forced-Air Cooling10.1016/j.apenergy.2015.03.080 ↗