The Process Optimization Analysis of CBN Abrasive Cu-Sn-Ti Coating Fabrication via the Ultrasonic-Vibration-Assisted Laser Cladding Method
Source abstract
Abstract
Ultra-precision machining has higher requirements for the performance of abrasive tools, but the traditional grinding wheel has some problems such as irregular grain arrangement, limited chip space, and high grinding temperature. Therefore, a structured grinding wheel suitable for ultra-precision machining is proposed. In this study, the laser cladding method and ultrasonic vibration technology were combined to study the preparation process of a structured grinding wheel. Firstly, the quality evaluation system of the printing layer was established, and the shape coefficient and dilution rate were used to evaluate the laser cladding quality. The effects of laser power, sweep speed, powder feeding speed, and ultrasonic power on the shape coefficient and dilution rate of the printing layer were analyzed by single-factor experiments. The level range of each factor in the orthogonal experiment was established to optimize the process parameters. The surface morphology was observed, and the influence of ultrasonic vibration on the morphology was analyzed. The structured grinding wheel was prepared according to the optimized parameters.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced machining processes and optimization · Tribology and Lubrication Engineering · Additive Manufacturing Materials and Processes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
School of Mechanical Engineering and Automation, Northeastern University, Shenyang 110819, China
Liaoning Provincial Key Laboratory of High-End Equipment Intelligent Design and Manufacturing Technology, Shenyang 110819, China
Funding
National Natural Science Foundation of China · Fundamental Research Funds for the Central Universities · Natural Science Foundation of Hebei Province · Science and Technology Project of Hebei Education Department
References (27)
Show source-provided references
1. Molecular dynamics simulation and experimental study of the material machinability characteristics and crack propagation mechanisms for fused silica double nanoscratches10.1016/j.triboint.2024.109982 ↗
2. Simulation and experimental investigation of material removal profile based on ultrasonic vibration polishing of K9 optical glass10.1016/j.triboint.2024.109730 ↗
3. Enhanced machinability of aluminium-based silicon carbide by non-resonant vibration-assisted magnetorheological finishing10.1016/j.jmatprotec.2023.118223 ↗
4. Material removal modes and processing mechanism in microultrasonic machining of ball ceramic tool10.1016/j.ceramint.2024.05.196 ↗
5. Mechanism of grinding wheel surface reproduction in regular surface texture generation10.1179/174329408X282596 ↗
6. Manufacturing of structured surfaces via grinding10.1016/j.jmatprotec.2016.12.009 ↗
7. Grinding process for profiled texturing10.1016/j.cirp.2016.04.116 ↗
8. Wear behaviors of electroplated CBN grinding wheel with orderly-micro-grooves in grinding narrow-deep slot10.1007/s00170-023-12509-4 ↗
9. Theoretical modeling and experimental study on grinding force of straight groove structured grinding wheel10.1007/s00170-022-10747-6 ↗
10. Study on flow field and convective heat transfer characteristics in grinding zone of large spiral angle flow disturbance grooved wheel10.1007/s00170-023-12226-y ↗
11. Improved grinding performance of SiC using an innovative bionic vein-like structured grinding wheel optimized by hydrodynamics10.1016/j.jmapro.2023.06.010 ↗
12. Research on the mapping grinding of dimple surface with ordered pattern based on topological theory10.1007/s00170-022-09711-1 ↗
13. The effects of structured grinding wheel designed parameters on the geometries of ground structured surfaces10.1007/s00170-022-09048-9 ↗
14. Study on bottom surface quality of sapphire micro-groove grinding with structured grinding wheel
15. The effect of force on the surface of rib grinding with ordered grinding wheel
16. Theoretical model and mechanism of mirror effect of spiral grooved grinding wheel
17. Study on the trailing wave surface of topological grinding array with structured grinding wheel
18. Study on the grinding surface of grain grain with end grinding wheel with grain blade sequence arrangement
19. Experimental study on grinding SIC ceramics with bird feather structure self-lubricating diamond wheel
20. Hou, Z., and Yao, Z. (2022, January 27–29). Grooving and Grinding Performance of Structured Wheels Fabricated with Diamond Cutting Blades. Proceedings of the 2022 International Conference on Mechanical Engineering and Power Engineering (MEPE), Wuhan, China.10.1109/MEPE56451.2022.10146706 ↗
21. Research on laser preparation and grinding performance of hydrophilic structured grinding wheels10.1016/j.ceramint.2022.10.240 ↗
22. Grooving profile control for structured grinding wheels with picosecond pulsed laser10.1007/s00170-022-08655-w ↗
23. Ma, M. (2022). Research on Ultrasonic-Assisted Laser 3D Printing Technology of Structured Grinding Wheel. [Master’ Thesis, Northeastern University].
24. Pts, 1–4, Kim, Y.J., Bae, H.D., and Kim, Y.J. (2005). The strength and hardness of metal matrix composites by binder additives. Advances in Fracture and Strength, Trans Tech Publications.
25. Investigation of the track width-dependent melt pool characteristics during laser-sintering of polyamide 12 in correlation to various focus diameters10.1007/s40964-020-00126-6 ↗
26. Teaching consideration of wetting Angle theory for evaluating heterogeneous nucleation effectiveness
27. Study on two kinds of cracking behavior and mechanism of cladding layer in laser rapid forming process