Strength and Deformation Analyses of Selected Filaments for Large-Format Additive Manufacturing Applicable to the Production of Firefighting Water Tanks
Source abstract
Abstract
Large-format additive manufacturing is a candidate for tremendous savings in terms of time and cost while simultaneously enabling higher flexibility, quality, and variability. Most of the design constraints of small-scale polymer 3D printers still apply to large-format additive manufacturing. The paper details both the strengths and deformation-related design considerations for additive manufacturing to gain a better understanding of the material capabilities and limitations, mechanical characteristics, and how to use them for large-format additive manufacturing (LFAM). The results show that the tested materials for additive manufacturing meet the requirements from the stress and deformation points of view. Compared to the steel and composite material, the strength limits are lower, but high enough for the given load. The materials HI TEMP, HI TEMP CF, PA12CF, PA6/66, and PLA seem to be the most promising for LFAM to create a firefighting water tank. The results may be considered as an introduction to further research that should lead to real solutions for the production of atypical tanks.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Manufacturing Process and Optimization · Innovations in Concrete and Construction Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanics, Mechanical Engineering and Design, Faculty of Technology, Technical University in Zvolen, 960 01 Zvolen, Slovakia
Department of Manufacturing Technology and Quality Management, Faculty of Technology, Technical University in Zvolen, 960 01 Zvolen, Slovakia
Funding
ERDF
References (61)
Show source-provided references
1. Hnilicová, M., and Hnilica, R. (2017). Use of composite materials to reduce the weight of superstructures for base machines/Využitie kompozitných materiálov za účelom zníženia hmotnosti nadstavieb pre bázové stroje. Kvalita, Technológie, Diagnostika v Technických Systémoch, SPU Nitra.
2. Chawla, K. (2016). Fibrous Materials, Cambridge University Press. [2nd ed.].10.1017/CBO9781139342520 ↗
3. Mechanical, thermal and interfacial properties of green composites from basalt and hybrid woven fabrics10.1007/s12221-016-6563-z ↗
4. Chawla, K.K. (2019). Composite Materials. Science and Engineering, Springer Nature. [2nd ed.].10.1007/978-3-030-28983-6 ↗
5. An application and market oriented review on large format additive manufacturing, focusing on polymer pellet-based 3D printing10.1007/s40964-022-00309-3 ↗
6. Influences of zirconium tungstate additives on characteristics of polyvinylidene fluoride (PVDF) components fabricated via material extrusion additive manufacturing process10.1007/s00170-019-03978-7 ↗
7. Current status and future roles of additives in 3D printing—A perspective10.1002/vnl.21887 ↗
8. Recent progress in beam-based metal additive manufacturing from a materials perspective: A review of patents10.1007/s11665-021-06273-3 ↗
9. Recent advances in development of additively manufactured thermosets and fiber reinforced thermosetting composites: Technologies, materials, and mechanical properties10.1016/j.compositesa.2023.107584 ↗
10. Processing and mechanical characterization of short carbon fiber-reinforced epoxy composites for material extrusion additive manufacturing10.1016/j.compositesb.2021.109122 ↗
11. Additive manufacturing of carbon fiber-reinforced plastic composites using fused deposition modeling: Effects of process parameters on tensile properties10.1177/0021998316646169 ↗
12. A review of additive manufacturing technologies and markets for thermosetting resins and their potential for carbon fiber integration
13. Material design factors in the additive manufacturing of Carbon Fiber Reinforced Plastic Composites: A state-of-the-art review
14. Fiber–matrix impregnation behavior during additive manufacturing of continuous carbon fiber reinforced polylactic acid composites
15. Effects of carbon fibre reinforcement on the geometric properties of PETG-based filament using FFF additive manufacturing10.1016/j.compositesb.2022.109766 ↗
16. A review on additive manufacturing of carbon fiber-reinforced polymers: Current methods, materials, mechanical properties, applications and challenges10.1002/app.53476 ↗
17. Additive manufacturing and mechanical performance of carbon fiber reinforced Polyamide-6 composites10.1016/j.matpr.2022.03.339 ↗
18. Kipping, J., and Schüppstuhl, T. (2023). Load-oriented nonplanar additive manufacturing method for optimized continuous carbon fiber parts. Materials, 16.10.3390/ma16030998 ↗
19. Varma, M.M.M.K., Baghel, P.K., and Raju, R. (2022). Additive manufacturing of thermosetting resins in-situ carbon fibers: A review. Recent. Adv. Mater. Mod. Manuf., 97–105.10.1007/978-981-19-0244-4_11 ↗
20. Semi-crystalline feedstock for filament-based 3D printing of polymers10.1016/j.progpolymsci.2021.101411 ↗
21. Current understanding and challenges in high temperature additive manufacturing of engineering thermoplastic polymers
22. Fused deposition modeling of thermoplastic elastomeric materials: Challenges and opportunities
23. Skočkovský, P., Bokůvka, O., Konečná, R., and Tillová, E. (2015). Náuka o Materiáli/Material Science, University of Žilina.
24. Love, L.J., Duty, C.E., Post, B.K., Lind, R.F., Lloyd, P.D., Kunc, V., Peter, W.H., and Blue, C.A. (2024, May 24). Breaking Barriers in Polymer Additive Manufacturing, Available online: https://www.osti.gov/servlets/purl/1185467.
25. Gibson, I., Rosen, D., and Stucker, B. (2015). Additive Manufacturing Technologies: 3D Printing, Rapid Prototyping, and Direct Digital Manufacturing, Springer. [2nd ed.].10.1007/978-1-4939-2113-3 ↗
26. Scott, J.A., Gupta, N., Weber, C., Newsome, S., Terry Wohlers, T., and Caffrey, T. (2012). Additive Manufacturing: Status and Opportunities Additive Manufacturing: Status and Opportunities, IDA, Science and Technology Policy Institute.
27. Ahuja, B., Karg, M., and Schmidt, M. (2015, January 16). Additive manufacturing in production: Challenges and opportunities. Proceedings of the Laser 3D Manufacturing II, San Francisco, CA, USA.10.1117/12.2082521 ↗
28. Status and perspectives for the use of additive technologies in various branches of Russian industry10.1088/1757-899X/483/1/012093 ↗
29. Sisca, F.G., Angioletti, C.M., Taisch, M., and Colwill, J.A. (2016, January 7–9). Additive manufacturing as a strategic tool for industrial competition. Proceedings of the IEEE 2nd International Forum on Research and Technologies for Society and Industry Leveraging a Better Tomorrow (RTSI), Bologna, Italy.10.1109/RTSI.2016.7740609 ↗
30. Additive manufacturing: Current state, future potential, gaps and needs, and recommendations10.1115/1.4028725 ↗
31. Designing for big area additive manufacturing
32. Hnilica, R., Ťavodová, M., Hnilicová, M., Matej, J., and Messingerová, V. (2020). The Innovative design of the fire-fighting adapter for forest machinery. Forests, 11.10.3390/f11080843 ↗
33. (2023, July 31). Owens Corning: OCV Reinforcements M5. Available online: https://romar-voss.nl/archief/Composites/versterking/pdf/Glasvezel%20versterkings%20materialen/Glasmat%20Emulsiegebonden/M5/ChoppedStrandMats_M5_emea_06_2008_Rev3.pdf.
34. (2023, July 31). Ashland: Technical Datasheet AROPOL™ M 105 TB. Available online: http://www.kokko-fiber.fi/tiedostot/AROPOL-M-105-TB.pdf.
35. (2023, July 25). BIGREP: Catalog Sheet. Available online: https://bigrep.com/filaments/.
36. Hnilicová, M., Chromek, I., Hnilica, R., Matej, J., and Messingerová, V. (2022). Fire-Fighting Adapter DATEFF for the Forest Wheeled Skidder. Current Issues in Forests Protection from Fires II, Technical University.
37. (2023, July 26). RAISE3D: 3D Printing Filament. Available online: https://www.raise3d.eu/filaments/.
38. Materials Requirements in Fused Filament Fabrication: A Framework for the Design of Next-Generation 3D Printable Thermoplastics and Composites10.1002/mame.202200197 ↗
39. Mechanical properties of thermoplastic polymers in fused filament fabrication (FFF)
40. A review on the fused deposition modeling (FDM) 3D printing: Filament processing, materials, and printing parameters10.1515/eng-2021-0063 ↗
41. (2023, July 27). FIBERLOGY: Filaments. Available online: https://fiberlogy.com/en/fiberlogy-filaments/.
42. (2023, July 27). Indicate Technologies: Filament. Available online: https://indicatetechnologies.com/collections/bigrep-filament-1.
43. (2023, July 27). ADMASYS: Additive Manufacturing Systems. Available online: https://admasys.sk/produkty/3d-tlaciarne/termoplasty/bigrep/.
44. The status, challenges, and future of additive manufacturing in engineering10.1016/j.cad.2015.04.001 ↗
45. A review of various materials for additive manufacturing: Recent trends and processing issues10.1016/j.jmrt.2022.10.015 ↗
46. Gebhardt, A., Kessler, J., and Thurn, L. (2011). 3D Printing: Understanding Additive Manufacturing, Hanser. [2nd ed.].
47. State-of-the-Art Review and Roadmap10.1007/978-3-030-44522-5_1 ↗
48. 3D printing: A critical review of current development and future prospects10.1108/RPJ-11-2018-0293 ↗
49. State of art review on sustainable additive manufacturing10.1108/RPJ-04-2018-0085 ↗
50. Economic sustainability of additive manufacturing: Contextual factors driving its performance in rapid prototyping10.1108/JMTM-05-2018-0131 ↗
51. Redesign and cost estimation of rapid manufactured plastic parts10.1108/13552541011065704 ↗
52. Towards a sustainable and economic selection of part candidates for additive manufacturing10.1108/RPJ-12-2014-0179 ↗
53. Additive manufacturing: Scientific and technological challenges, market uptake and opportunities10.1016/j.mattod.2017.07.001 ↗
54. Additive manufacturing—A review of 4D printing and future applications
55. Additive manufacturing (3D printing): A review of materials, methods, applications and challenges10.1016/j.compositesb.2018.02.012 ↗
56. Post, B.K., Richardson, B., Lind, R., Love, L.J., Lloyd, P., Kunc, V., Rhyne, B.J., Roschli, A., Hannan, J., and Nolet, S. (2017, January 7–9). Big area additive manufacturing application in wind turbine molds. Proceedings of the 28th Annual International Solid Freeform Fabrication Symposium—An Additive Manufacturing Conference, Austin, TX, USA.
57. Coupled thermo-mechanical numerical model to minimize risk in large-format additive manufacturing of thermoplastic composite designs10.1007/s40964-022-00349-9 ↗
58. Peterson, E. (2021). Technical challenges to adopting large scale additive manufacturing for the production of yacht hulls. Human Systems Engineering and Design III, Springer.10.1007/978-3-030-58282-1_3 ↗
59. Large-format fused deposition additive manufacturing: A review10.1108/RPJ-05-2018-0126 ↗
60. Adaptive platforms and flexible deposition system for big area additive manufacturing (BAAM)10.4028/www.scientific.net/AMM.890.3 ↗
61. Development and demonstration of large scale metal additive manufacturing for military vehicle applications-final report