Potential Evaluation of Twin-Screw Air Expanders with Dual-Lead Rotors Used in PEMFC Systems
Source abstract
Abstract
The reduction in the power cost of air supply systems has emerged as a critical challenge in the development of polymer electrolyte membrane fuel cells. This study proposes the use of dual-lead rotors to improve the performance of twin-screw expanders for the purpose of boosting expanders’ recovery power and consequently lowering the power cost of the air supply subsystem, which is hardly investigated in previous publications. For this purpose, a mathematical model is built to assess the potential of improving the expander performance by means of the dual-lead rotors. And the influence of lead and length of the high-pressure rotor segment and overall rotor length are analyzed. The results demonstrate that the smaller lead and larger length of the high-pressure rotor segment result in better geometric characteristics and thus thermodynamic performance. For example, case #4 with dual-lead rotors exhibits a larger rotating angle at the suction end and a larger suction area than those of constant-lead rotors by 43° and 100%, respectively, which further lower the suction pressure loss. Compared with constant-lead rotors, the maximum increments in the mass flowrate and indicated power are observed as 45% and 25.4%, respectively. However, the dual-lead rotors could not effectively contribute to an increase in the isentropic indicated efficiency of twin-screw expanders due to the severe leakage, and hence, it becomes crucial to address the leakage issues in twin-screw expanders.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Fuel Cells and Related Materials · Advancements in Solid Oxide Fuel Cells · Electrocatalysts for Energy Conversion
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
School of Energy and Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China
Funding
National Natural Science Foundation of China · The China Postdoctoral Science Foundation · Open Foundation of State Key Laboratory of Compressor Technology
References (41)
Show source-provided references
1. Experimental analysis of optimal performance for a 5 kW PEMFC system10.1016/j.ijhydene.2018.08.157 ↗
2. Akpolat, A.N., Dursun, E., and Yang, Y. (2023). Performance Analysis of a PEMFC-Based Grid-Connected Distributed Generation System. Appl. Sci., 13.10.3390/app13063521 ↗
3. Materials, technological status, and fundamentals of PEM fuel cells—A review10.1016/j.mattod.2019.06.005 ↗
4. Air supply regulation for PEMFC systems based on uncertainty and disturbance estimation10.1016/j.ijhydene.2018.01.189 ↗
5. Kerviel, A., Pesyridis, A., Mohammed, A., and Chalet, D. (2018). An evaluation of turbocharging and supercharging options for high-efficiency fuel cell electric vehicles. Appl. Sci., 8.10.3390/app8122474 ↗
6. Coordination control strategy for the air management of heavy vehicle fuel cell engine10.1016/j.ijhydene.2019.10.134 ↗
7. Gas purging effect on the degradation characteristic of a proton exchange membrane fuel cell with dead-ended mode operation I. With different electrolytes10.1016/j.energy.2017.09.067 ↗
8. Efficiency improvement of a PEMFC power source by optimization of the air management10.1016/j.ijhydene.2012.02.029 ↗
9. Analysis of air compression, progress of compressor and control for optimal energy efficiency in proton exchange membrane fuel cell10.1016/j.rser.2020.110304 ↗
10. Air mass flow and pressure optimisation of a PEM fuel cell range extender system10.1016/j.ijhydene.2020.07.176 ↗
11. Exergoeconomic analysis of vehicular PEM (proton exchange membrane) fuel cell systems with and without expander10.1016/j.energy.2014.09.054 ↗
12. Efficiency improvement and Thermo-economic analysis of proton exchange membrane fuel cell system with energy recovery for both air and hydrogen10.1016/j.applthermaleng.2023.121114 ↗
13. Energy recovery and efficiency improvement method of proton exchange membrane fuel cell system by applying the expander in plateau environment10.1016/j.jpowsour.2024.234903 ↗
14. Bielka, P., and Kuczyński, S. (2022). Energy Recovery from Natural Gas Pressure Reduction Stations with the Use of Turboexpanders: Static and Dynamic Simulations. Energies, 15.10.3390/en15238890 ↗
15. Modeling and simulation of the PEMFC system equipped with a variable geometry turbocharger10.1016/j.ijhydene.2024.06.283 ↗
16. Stretch, D., Eybergen, W., and Wright, B. (2013). Roots Air Management System with Integrated Expander, Eaton Corporation. FY 2013 Annual Progress Report.
17. Stretch, D., Eybergen, W., and Wright, B. (2014). Roots Air Management System with Integrated Expander. Eaton Corporation. FY 2014 Annual Progress Report.
18. Stretch, D., Eybergen, W., and Wright, B. (2015). Roots Air Management System with Integrated Expander. Eaton Corporation. FY 2015 Annual Progress Report.10.2172/1325976 ↗
19. Numerical Investigation of the Influence of Different Suction and Discharge Ports on Scroll Expander Performance10.2174/1872212117666221028161158 ↗
20. Performance Analysis of a Combined Scroll Expander-compressor unit for a Fuel Cell System
21. Oscarsson, J. (2003). Power Recovery by a Twin Screw Expander in a Fuel Cell Application, SAE International. SAE Technical Paper; No. 2003-01-0411.10.4271/2003-01-0411 ↗
22. Steady Operating Behaviour of a Screw-Type Supercharger-Expander Module for an Automotive Fuel Cell System
23. Venturi, M., Sang, J., Knoop, A., and Hornburg, G. (2012). Air Supply System for Automotive Fuel Cell Application, SAE International. SAE Technical Paper; No. 2012-01-1225.10.4271/2012-01-1225 ↗
24. Air compressors for fuel cell vehicles: An systematic review10.4271/2015-01-1172 ↗
25. Wiartalla, A., Pischinger, S., Bornscheuer, W., Fieweger, K., and Ogrzewalla, J. (2000). Compressor Expander Units for Fuel Cell Systems, SAE International. SAE Technical Paper; No. 2000-01-0380.10.4271/2000-01-0380 ↗
26. Kulp, G.W., and Nelson, D.J. (2001). A Comparison of Two Fuel Cell Air Compression Systems at Low Load, SAE International. SAE Technical Paper; No. 2001-01-2537.10.4271/2001-01-2547 ↗
27. Jiang, B., and Fitzgerald, B. (2021). Development of an Optimized Rotary Screw Air Compressor for the Electrical Vehicle Air Brake Systems/Suspension Systems on Trucks and Buses, SAE International. SAE Technical Paper; No. 0148-7191.10.4271/2021-01-1281 ↗
28. Stosic, N., Smith, I.K., Kovacevic, A., and Mujic, E. (2010). Development of Water Lubricated Compressor-Expander for Fuel Cell Application. ASME 2010 International Mechanical Engineering Congress and Exposition, ASME.10.1115/IMECE2010-37437 ↗
29. Hütker, J., and Brümmer, A. (2013, January 9–10). Physics of a dry running unsynchronized twin screw expander. Proceedings of the 8th International Conference on Compressors and Their Systems, London, UK.10.1533/9781782421702.8.407 ↗
30. Kovacevic, A., and Rane, S. (2013, January 9–10). 3D CFD analysis of a twin screw expander. Proceedings of the Institution of Mechanical Engineers-8th International Conference on Compressors and Their Systems, London, UK.10.1533/9781782421702.8.417 ↗
31. Experimental study on the performance of oil-free twin-screw expanders for recovering energy in fuel cell systems10.1016/j.applthermaleng.2019.114613 ↗
32. Loss analysis of oil-free twin-screw expanders for recovering energy in fuel cell systems by means of p-θ diagrams10.1016/j.energy.2020.117581 ↗
33. Comparison of thermodynamic efficiency between constant, dual and multiple lead rotors for an industrial air screw compressor10.1088/1757-899X/425/1/012025 ↗
34. Deforming grid generation and CFD analysis of variable geometry screw compressors10.1016/j.compfluid.2014.04.024 ↗
35. Energy potential of dual lead rotors for twin screw compressors10.1088/1757-899X/232/1/012018 ↗
36. Utri, M., and Brümmer, A. (2016, January 11–14). Improvement of the efficiency of twin-screw refrigeration compressors by means of dual lead rotors. Proceedings of the International Compressor Engineering Conference, West Lafayette, IN, USA.
37. Opportunities for variable rotor lead in screw compressors depending on dimensionless numbers10.1177/0954408918802716 ↗
38. Wu, H., Liu, J., Shen, Y., Liang, M., and Zhang, B. (2021). Research on Performance of Variable-Lead Rotor Twin Screw Compressor. Energies, 14.10.3390/en14216970 ↗
39. Denver, G. (2024, October 19). Positive Displacement Blowers & Vacuum Pumps CycloBlower®VHX Series. Available online: https://gdequipment.com/wp-content/uploads/2019/06/CycloBlower-VHX-Brochure.pdf.
40. A general mathematical model for screw-rotor honing using an internal-meshing honing machine10.1016/j.mechmachtheory.2020.104038 ↗
41. Performance improvement of twin-screw air expander used in PEMFC systems by two-phase expansion10.1016/j.energy.2023.127249 ↗