Experimental Analysis and Design of 3D-Printed Polymer Elliptical Tubes in Compression
Source abstract
Abstract
Local failure modes occurring in 3D-printed polymer elliptical section tubes in compression are investigated in the present study via a series of experiments, with the results compared to existing design proposals for slender steel analogues. Polylactic acid (PLA) and acrylonitrile butadiene styrene material specimens (ABS) have been printed in three orthogonal layering orientations, and tested in tension and compression to determine orthotropic material properties including strength, elastic modulus, failure strains and Poisson’s ratio. Next, twenty-four 3D-printed elliptical cross-section tubes are tested in compression, with the polymer material, cross-sectional aspect ratio and tube wall thickness varied across the set. Results including the load-deflection behaviour, longitudinal strains, failure modes and ultimate loads are discussed. A design method formulated previously for slender steel elliptical hollow sections in compression is adapted for use with the 3D-printed polymer specimens. Upon appropriate rescaling of the design parameters, safe-sided and accurate predictions are provided by the design method for the compressive resistance of the PLA and ABS elliptical specimens, thus validating its application to cross-sections in materials other than carbon steel.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Innovations in Concrete and Construction Materials · biodegradable polymer synthesis and properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
School of Architecture, Building and Civil Engineering, Loughborough University, Loughborough LE11 3TU, UK
School of the Built Environment and Architecture, London South Bank University, London SE1 0AA, UK
Funding
UK Manufacturing Symbiosis Network Plus (UKMSN+) · Digital Architecture and Robotics Laboratory and the Division of Civil and Building Services Engineering within the School of the Built Environment and Architecture at London South Bank University · Loughborough University
References (48)
Show source-provided references
1. Rodríguez-Panes, A., Claver, J., and Camacho, A.M. (2018). The Influence of Manufacturing Parameters on the Mechanical Behaviour of PLA and ABS Pieces Manufactured by FDM: A Comparative Analysis. Materials, 11.10.3390/ma11081333 ↗
2. Physical and mechanical properties of PLA, and their functions in widespread applications—A comprehensive review10.1016/j.addr.2016.06.012 ↗
3. Buckling developed in 3D printed PLA cuboidal samples under compression: Analytical, numerical and experimental investigations
4. Tribological studies of 3D printed ABS and PLA plastic parts10.1016/j.matpr.2020.09.235 ↗
5. Hsueh, M.H., Lai, C.J., Wang, S.H., Zeng, Y.S., Hsieh, C.H., Pan, C.Y., and Huang, W.C. (2021). Effect of printing parameters on the thermal and mechanical properties of 3D-Printed PLA and PETG using Fused Deposition Modeling. Polymers, 3.10.3390/polym13111758 ↗
6. (2018). UM180821 TDS PLA RB V11 Technical Data Sheet PLA, Ultimaker.
7. (2018). Technical Data Sheet—ABSX, MCPP.
8. Gauss, Landen, Ramanujan, the Arithmetic-geometric Mean, Ellipses, π, and the Ladies Diary
9. Investigation of heat transfer characteristics of deflected elliptical-tube heat exchanger in closed-circuit cooling towers10.1016/j.applthermaleng.2023.121860 ↗
10. A comparative study of latent heat thermal energy storage (LTES) system using cylindrical and elliptical tubes in a staggered tube arrangement10.1016/j.est.2024.111333 ↗
11. On numerical stability analysis of fluid flows in compliant pipes of elliptic cross-section10.1016/j.jfluidstructs.2021.103414 ↗
12. Flow three-dimensionality of wavy elliptic cylinder: Vortex shedding bifurcation10.1016/j.oceaneng.2024.117527 ↗
13. Elastic buckling of elliptical tubes10.1016/j.tws.2008.01.036 ↗
14. Kempner, J., and Chen, Y.N. (September, January 30). Large deflections of an axially compressed oval cylindrical shell. Proceedings of the 11th International Congress of Applied Mechanics, Munich, Germany.
15. Stability of oval cylindrical shells10.1007/BF02327691 ↗
16. Elastic local postbuckling of elliptical tubes10.1016/j.jcsr.2010.11.004 ↗
17. Analytical modelling of plastic collapse in compressed elliptical hollow sections10.1016/j.jcsr.2010.11.012 ↗
18. Elastic buckling of elliptical tubes subjected to generalised linearly varying stress distributions10.1016/j.tws.2012.04.016 ↗
19. Strength enhancement and stub-column behavior of cold-formed stainless steel elliptical hollow sections10.1016/j.tws.2023.110939 ↗
20. Theoretical prediction and numerical analysis for axial crushing behaviour of elliptical aluminium foam-filled tube10.1016/j.tws.2019.106523 ↗
21. Structural applications of fibre reinforced polymer (FRP)composite tubes: A review of columns members10.1016/j.compstruct.2018.07.109 ↗
22. Local buckling and ultimate strength of slender elliptical hollow sections in compression10.1016/j.engstruct.2015.12.020 ↗
23. Numerical analysis and design of slender elliptical hollow sections in bending10.1016/j.tws.2019.03.011 ↗
24. Characterization of the mechanical response of thermoplastic parts fabricated with 3D printing10.1007/s00170-019-04194-z ↗
25. Tensile, compression, and flexural characteristics of acrylonitrile–butadiene–styrene at low strain rates: Experimental and numerical investigation
26. Effect of print speed and extrusion temperature on properties of 3D printed PLA used fused deposition modeling process10.1016/j.matpr.2021.02.137 ↗
27. The influence of in-plane raster angle on tensile and fracture strengths of 3D-printed PLA specimens10.1016/j.engfracmech.2020.107225 ↗
28. Controlling toughness and strength of FDM 3D-printed PLA components through the raster layup10.1016/j.compositesb.2019.107562 ↗
29. Structural behavior of shallow geodesic lattice domes10.1016/j.ijsolstr.2018.07.022 ↗
30. On the geometric conditions for multiple stable equilibria in clamped arches10.1016/j.ijnonlinmec.2017.03.009 ↗
31. Effect of layer thickness and cross-section geometry on the tensile and compression properties of 3D printed ABS10.1016/j.mtcomm.2019.100626 ↗
32. Anisotropic properties of 3-D printed Poly Lactic Acid (PLA) and Acrylonitrile Butadiene Styrene (ABS) plastics10.1016/j.rinma.2021.100227 ↗
33. (1996). Plastics—Determination of Tensile Properties—Part 2: Test Conditions for Moulding and Extrusion Plastics (Standard No. EN ISO 527-2).
34. Prusa (2021, December 13). PrusaSlicer 2.4.0 Manual. Available online: https://help.prusa3d.com/en/article/general-info_1910.
35. (1993). Plastics—Determination of Tensile Properties—Part 1: General Principles (Standard No. EN ISO 527-1).
36. (2016). Standard Test Method for Compressive Properties of Rigid Plastics (Standard No. ASTM D695).
37. The mechanical properties of cellular solids10.1007/BF02645546 ↗
38. Ramberg, W., and Osgood, W.R. (1943). Description of Stress–Strain Curves by Three Parameters. Technical Note No. 902, National Advisory Committee for Aeronautics.
39. Experimental characterization and micrography of 3D printed PLA and PLA reinforced with short carbon fibers10.1016/j.compositesb.2017.05.013 ↗
40. Isotropic and anisotropic elasticity and yielding of 3D printed material10.1016/j.compositesb.2016.06.009 ↗
41. McCann, F., and Rossi, F. (2021, January 12–14). Investigating local buckling in highly slender elliptical hollow sections through analysis of 3D-printed analogues. Proceedings of the 8th International Conference on Coupled Instabilities in Metal Structures, Łodz, Poland.10.2139/ssrn.3867308 ↗
42. Theory of Non-Newtonian Flow
43. Anisotropic rate-dependent mechanical behavior of Poly (Lactic Acid) processed by Material Extrusion Additive Manufacturing
44. Cross-section classification of elliptical hollow sections10.12989/scs.2007.7.3.185 ↗
45. Compressive resistance of hot-rolled elliptical hollow sections10.1016/j.engstruct.2007.04.019 ↗
46. (2024). Eurocode 3: Design of Steel Structure—Part 1–1: General Rules for Buildings (Standard No. EN 1993-1-1).
47. (2006). Eurocode 3: Design of Steel Structures—Part 1–4: General Rules—Supplementary Rules for Stainless Steels (Standard No. EN 1993-1-4).
48. Tsai, S.W., and Wu, E.M. (1972). A general theory of strength for anisotropic materials. Technical Report AFML-TR-71-12, August 1972, Air Force Materials Laboratory.10.21236/ADA306350 ↗