journal article·2023-06-02Open access

Tensile Stress Evolution Outside Deformation Zone of Cold Rolled Strip

Kangwu Zhang, Dongcheng Wang, Yanghuan Xu, Hongmin Liu

Applied Sciences· Volume 13· Issue 11

Abstract

To determine the exact distribution of tensile stress in a cold rolled strip, tensile stress evolution caused by lateral uneven velocity distribution outside the deformation zone of the strip is examined. The finite difference method is employed to solve the problem. Different factors, including the strip width and the form and amplitude of the initial stress distribution on the stress evolution, are analyzed. On the one hand, to improve the calculation speed, a “Gaussian” curve is proposed to fit the results calculated by the finite difference method. Simulation results show that the stress evolution calculated by the fitting equation is in good agreement with that obtained by the finite difference method. On the other hand, to verify the exactness of the model, an experiment is conducted, and the comparison between the calculated results and experimental values is discussed.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal Forming Simulation Techniques · Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

National Engineering Research Center for Equipment and Technology of Cold Rolling Strip, Yanshan University, Qinhuangdao 066004, China

National Key Laboratory of Metal Forming Technology and Heavy Equipment, China National Heavy Machinery Research Institute Co., Ltd., Xi’an 710032, China

State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004, China

Funding

National Natural Science foundation of China · National Key Laboratory of Metal Forming Technology and Heavy Equipment, China National Heavy Machinery Research Institute Co., Ltd., Xi’an

References (27)

Show source-provided references
1. Data-based flatness prediction and optimization in tandem cold rolling10.1007/s42243-020-00505-x ↗
2. Wang, Y.S., Xu, X.D., Ren, B.B., Liu, J., and Zhao, R.G. (2021). Effect of Geometrical Factors on Torsion in Cold Roll Forming of the Lower Side Beam of a Car. Appl. Sci., 11.10.3390/app11177852 ↗
3. Roh, Y.H., Byon, S.M., and Lee, Y. (2021). Numerical Analysis of Edge Cracking in High-Silicon Steel during Cold Rolling with 3D Fracture Locus. Appl. Sci., 11.10.3390/app11188408 ↗
4. Xu, D., Yang, Q., Wang, X.C., He, H., Sun, Y.Z., and Li, W.P. (2020). An Experimental Investigation of Steel Surface Topography Transfer by Cold Rolling. Micromachines, 11.10.3390/mi11100916 ↗
5. Research and Development Trend of Shape Control for Cold Rolling Strip10.1007/s10033-017-0163-8 ↗
6. Yi, G.D., Liang, Y., Wang, C., and Xu, J.H. (2019). Evolution of Residual Stress Based on Curvature Coupling in Multi-Roll Levelling. Appl. Sci., 9.10.3390/app9224975 ↗
7. Roll Bending Methods of Crown Control in Four-High Plate Mills
8. Analysis on solution of residual stress for cold rolling strip
9. Xu, L.J. (2007). Flatness Control in Cold Strip Rolling and Mill Type Selection, Metallurgical Industry Press.
10. 2-Dimensional lateral-material-flow model reduced from 3-Dimensional theory for flat rolling10.2355/isijinternational.31.550 ↗
11. A new model for the prediction of roll force and tension profiles in flat rolling10.2355/isijinternational.50.1644 ↗
12. Bryant, G.F. (1973). Automation of Tandem Mills, The Iron and Steel Institute.
13. Ishikawa, T., Tozawa, Y., Yukawa, N., and Yamanaka, M. (1984). Advanced Technology of Plasticity, Springer.
14. Liu, X.H., Jiang, Z.Y., and Wang, G.D. (1993). Advanced Technology of Plasticity, Springer.
15. A model coupling method for shape prediction10.1016/S1006-706X(12)60055-7 ↗
16. Analysis of profile and shape control in flat rolling
17. Strip layer method for analysis of the three-dimensional stresses and spread of large cylindrical shell rolling10.3901/CJME.2014.1210.177 ↗
18. Study on the transverse distributions of front and back tensions in strip rolled 4-high mill
19. Liu, H.M. (1999). Three Dimensional Rolling Theory and Application, Science Press.
20. Three-dimensional analysis of sheet rolling considering roll deformation
21. An advanced model for flatness and profile prediction in hot rolling
22. Yuen, W.Y., and Cozijnsen, M. (2002, January 8–11). Strip Shape Analysis in Cold Rolling. Proceedings of the 44th Mechanical Working and Steel Processing Conference Proceedings, Orlando, FL, USA.
23. An efficient method for strip flatness analysis in cold rolling
24. Cao, H.D. (1981). Plastic Deformation Mechanics Basis and Rolling Theory, Mechanical Industry Press.
25. The decay of stresses induced by flat rolling of metal strip10.1016/0020-7403(93)90028-S ↗
26. Li, W.T., Huang, B.H., and Bi, Z.B. (2006). Analysis and Application of Thermal Stress Theory, China Electric Power Press.
27. Entry and exit stress variation of cold rolling strip10.1016/S1006-706X(12)60121-6 ↗