Development and Characteristics of Ultra-Lightweight Concrete Mixed with Polyvinyl Alcohol Solution and Perlite
Source abstract
Abstract
Polyvinyl alcohol (PVA) is a nontoxic, biodegradable, water-soluble polymer used in various fields. The use of PVA in concrete has been limited due to problems such as initial setting delay, early age strength reduction, and decreased mechanical and durability performance caused by the generation of microbubbles. This study aims to verify the performance and effectiveness of PVA as a foaming agent by reversely utilizing the microbubble generation phenomenon of PVA, which has been recognized as a problem. In addition, the production and characteristics of ultra-light foamed concrete were evaluated using perlite (PL). PVA solutions with concentrations of 2.5% and 5.0% were considered. PL ratios of 10% (P1), 20% (P2), 30% (P3), and 40% (P4) were applied to the mass of the PVA solution. The mass of PVA solution (s), OPC (c), and PL considered in the experiment were classified into s/c, s/PL, PL/c, and s/(c + PL), respectively, and the optimal mixing ratio was presented based on the experimental results. In addition, a new high-temperature-curing method was applied that combines high-temperature wet curing (60 °C, relative humidity 90% or higher) and high-temperature dry curing (105 ± 5 °C) to improve the strength reduction problem at the early age and to increase the pore expansion effect. In addition, thermal analysis (TG/DTA), X-ray diffeaction (XRD), and Fourier transform infrared spectroscopy (FT-IR) were applied to analyze the hydration reaction products. The formed pores were imaged from the cross-section of each sample using an optical microscope, and the pore size was measured using image-processing software. The experimental results proved that PVA is a sufficiently effective material as a foaming agent for manufacturing foamed concrete in a high-temperature-curing environment. PVA showed a synergistic effect in expanding pores and increasing porosity, and PL improved insulation and lightweight. The manufactured ultralight foam concrete had a density of less than 1.0 g/cm 3 , a strength of 1–6 MPa, and a thermal conductivity of 0.13–0.19 W/m∙K. The appropriate mixing ratios within the range considered in this study were s/PL ratio of 5–3.33, PL/c ratio of 0.2–0.45, and s/(c + PL) ratio of 0.77–1.25.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Innovations in Concrete and Construction Materials · Concrete and Cement Materials Research · Innovative concrete reinforcement materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (64)
Show source-provided references
1. Alexa-Stratulat, S., Taranu, G., Toma, A., Olteanu, I., Pastia, C., Bunea, G., & Toma, I. (2024). Effect of expanded perlite aggregates and temperature on the strength and dynamic elastic properties of cement mortar. Construction and Building Materials, 438, Article 137229. https://doi.org/10.1016/j.conbuildmat.2024.13722910.1016/j.conbuildmat.2024.137229 ↗
2. Allahverdi, A., Kianpur, K., & Moghbeli, M. R. (2010). Effect of polyvinyl alcohol on flexural strength and some important physical properties of Portland cement paste. Iranian Journal of Materials Science and Engineering, 7(1), 1–6.
3. Bakhshi, M., Dalalbashi, A., & Soheili, H. (2023). Energy dissipation capacity of an optimized structural lightweight perlite concrete. Construction and Building Materials, 389, Article 131765. https://doi.org/10.1016/j.conbuildmat.2023.13176510.1016/j.conbuildmat.2023.131765 ↗
4. Balaha, M. M., Badawy, A. A. M., & Hashish, M. (2007). Effect of using ground waste tire rubber as fine aggregate on the behaviour of concrete mixes. Indian Journal of Engineering and Materials Sciences, 14(6), 427–435.
5. Bayat, A., Hassani, A., & Yousefi, A. A. (2018). Effects of red mud on the properties of fresh and hardened alkali-activated slag paste and mortar. Construction and Building Materials, 167, 775–790. https://doi.org/10.1016/j.conbuildmat.2018.02.10510.1016/j.conbuildmat.2018.02.105 ↗
6. Budrugeac, P. (2008). Kinetics of the complex process of thermo-oxidative degradation of poly(vinyl alcohol). Journal of Thermal Analysis and Calorimetry, 92, 291–296. https://doi.org/10.1007/s10973-007-8770-810.1007/s10973-007-8770-8 ↗
7. Cao, D., Gu, Y., Jiang, L., Jin, W., Lyu, K., & Guo, M. (2023). Effect of polyvinyl alcohol on the performance of carbon fixation foam concrete. Construction and Building Materials, 390, Article 131775. https://doi.org/10.1016/j.conbuildmat.2023.13177510.1016/j.conbuildmat.2023.131775 ↗
8. Carballosa, P., García Calvo, J. L., & Revuelta, D. (2020). Influence of expansive calcium sulfoaluminate agent dosage on properties and microstructure of expansive self-compacting concretes. Cement and Concrete Composites, 107, Article 103464. https://doi.org/10.1016/j.cemconcomp.2019.10346410.1016/j.cemconcomp.2019.103464 ↗
9. Celik, S., Family, R., & Menguc, M. P. (2016). Analysis of perlite and pumice based building insulation materials. Journal of Building Engineering, 6, 105–111. https://doi.org/10.1016/j.jobe.2016.02.01510.1016/j.jobe.2016.02.015 ↗
10. Choudhary, H. K., Anupama, A. V., Kumar, R., Panzi, M. E., Matteppanavar, S., Sherika, B. N., & Sahoo, B. (2015). Observation of phase transformations in cement during hydration. Construction and Building Materials, 101, 122–129. https://doi.org/10.1016/j.conbuildmat.2015.10.02710.1016/j.conbuildmat.2015.10.027 ↗
11. Davraz, M., Koru, M., Akdağ Kılınçarslan, A.E., Delikanlı, Y.E., & Çabuk, M. (2020). Investigating the use of raw perlite to produce monolithic thermal insulation material, Construction and Building Materials, 120674. https://doi.org/10.1016/J.CONBUILDMAT.2020.12067410.1016/J.CONBUILDMAT.2020.120674 ↗
12. Demirboga, R., & Gül, R. (2003). The effects of expanded perlite aggregate, silica fume and fly ash on the thermal conductivity of lightweight concrete. Cement and Concrete Research, 33, 723–727. https://doi.org/10.1016/S0008-8846(02)01032-310.1016/S0008-8846(02)01032-3 ↗
13. Demirboğa, R., Örüng, I., & Gül, R. (2001). Effects of expanded perlite aggregate and mineral admixtures on the compressive strength of low-density concretes. Cement and Concrete Research, 31(11), 1627–1632. https://doi.org/10.1016/S0008-8846(01)00615-910.1016/S0008-8846(01)00615-9 ↗
14. Deng, Q., Li, J., Yang, J., & Li, D. (2014). Optical and flexible a-chitin nanofibers reinforced poly(vinyl alcohol) (PVA) composite film: Fabrication and property. Composites Part a, Applied Science and Manufacturing, 67, 55–60. https://doi.org/10.1016/j.compositesa.2014.08.01310.1016/j.compositesa.2014.08.013 ↗
15. Dong, D., Huang, Y., Gao, X., Bian, Y., Zhu, J., Hou, P., Chen, H., Zhao, P., Wang, S., & Lu, L. (2023). Effect of polyvinyl alcohol powder on the impermeability, frost resistance and pore structure of calcium sulfoaluminate cement concrete. Construction and Building Materials, 409, Article 133858. https://doi.org/10.1016/j.conbuildmat.2023.13385810.1016/j.conbuildmat.2023.133858 ↗
16. García Calvo, J. L., Carballosa, P., Pedrosa, F., & Revuelta, D. (2022). Microstructural phenomena involved in the expansive performance of cement pastes based on type K expansive agent. Cement and Concrete Research, 158, Article 106856. https://doi.org/10.1016/j.cemconres.2022.10685610.1016/j.cemconres.2022.106856 ↗
17. Georgescu, M., Puri, A., Coarna, M., Viocu, G., & Voinitchi, D. (2002). Thermoanalytical and infrared spectroscopy investigations of some mineral pastes containing organic polymers. Cement and Concrete Research, 32, 1269–1275. https://doi.org/10.1016/S0008-8846(02)00762-710.1016/S0008-8846(02)00762-7 ↗
18. Horgnies, M., Chen, J. J., & Bouillon, C. (2013). Overview about the use of Fourier transform infrared spectroscopy to study cementitious materials. WIT Transactions on Engineering Sciences, 77, 251–262. https://doi.org/10.2495/MC13022110.2495/MC130221 ↗
19. Huiwen, W., Liyuan, Y., & Zhonghe, S. (2006). Modificatin of ITZ structure and properties of regenerated concrete. Journal of Wuhan University of Technology-Materials Science Edition, 21, 128–132. https://doi.org/10.1007/BF0284085810.1007/BF02840858 ↗
20. Ibrahim, M., Ahmad, A., Barry, M. S., Alhems, L. M., & Mohamed Suhoothi, A. C. (2020). Durability of structural lightweight concrete containing expanded perlite aggregate. International Journal of Concrete Structures and Materials, 14, 1–15. https://doi.org/10.1186/s40069-020-00425-w10.1186/s40069-020-00425-w ↗
21. Karakaş, H., İlkentapar, S., Durak, U., Örklemez, E., Özuzun, S., Karahan, O., & Atiş, C. D. (2023). Properties of fly ash-based lightweight-geopolymer mortars containing perlite aggregates: Mechanical, microstructure, and thermal conductivity coefficient. Construction and Building Materials, 362, Article 129717. https://doi.org/10.1016/j.conbuildmat.2022.12971710.1016/j.conbuildmat.2022.129717 ↗
22. Kim, J. H., Robertson, R. E., & Naaman, A. E. (1999). Structure and properties of poly(vinyl alcohol)—modified mortar and concrete. Cement and Concrete Research, 29(3), 407–415. https://doi.org/10.1016/S0008-8846(98)00246-410.1016/S0008-8846(98)00246-4 ↗
23. Kim, J. H., & Robertson, R. E. (1998). Effects of polyvinyl alcohol on aggregate-paste bond strength and the interfacial transition zone. Advanced Cement Based Materials, 8(2), 66–76. https://doi.org/10.1016/S1065-7355(98)00009-110.1016/S1065-7355(98)00009-1 ↗
24. Kim, J. H., & Robertson, R. E. (1997). Prevention of air void formation in polymer-modified cement mortar by pre-wetting. Cement and Concrete Research, 27(2), 171–176. https://doi.org/10.1016/S0008-8846(97)00001-X10.1016/S0008-8846(97)00001-X ↗
25. Knapen, E., & Van Gemert, D. (2006). Water-soluble polymers for modification of cement mortars. In Proceedings of 11th international symposium on fiber reinforced polymer for reinforced concrete structures (FRPRCS-11), 85–93.
26. Kou, S. C., & Poon, C. S. (2010). Properties of concrete prepared with PVA-impregnated recycled concrete aggregates. Cement and Concrete Composites, 32(8), 649–654. https://doi.org/10.1016/j.cemconcomp.2010.05.00310.1016/j.cemconcomp.2010.05.003 ↗
27. Lemougna, P. N., Wang, K., Tang, Q., & Cui, X. (2017). Study on the development of inorganic polymers from red mud and slag system: Application in mortar and lightweight materials. Construction and Building Materials, 156, 486–495. https://doi.org/10.1016/j.conbuildmat.2017.09.01510.1016/j.conbuildmat.2017.09.015 ↗
28. Liu, F., Wang, B., Xing, Y., Zhang, K., & Jiang, W. (2020). Effect of polyvinyl alcohol on the rheological properties of cement mortar. Molecules, 25(3), 754. https://doi.org/10.3390/molecules2503075410.3390/molecules25030754 ↗
29. Lu, Z., Hanif, A., Lu, C., Sun, G., Cheng, Y., & Li, Z. (2018). Thermal, mechanical, and surface properties of poly(vinyl alcohol) (PVA) polymer modified cementitious composites for sustainable development. Journal of Applied Polymer Science, 135(15), 46177. https://doi.org/10.1002/app.4617710.1002/app.46177 ↗
30. Luo, Z., Hao, Y., Mu, Y., Tang, C., & Liu, X. (2022). Solidification/stabilization of red mud with natural radionuclides in granular blast furnace slag based geopolymers. Construction and Building Materials, 316, Article 125916. https://doi.org/10.1016/j.conbuildmat.2021.12591610.1016/j.conbuildmat.2021.125916 ↗
31. Ma, J., Yu, Z., Ni, C., Shi, H., & Shen, X. (2019). Effects of limestone powder on the hydration and microstructure development of calcium sulphoaluminate cement under long-term curing. Construction and Building Materials, 199, 688–695. https://doi.org/10.1016/j.conbuildmat.2018.12.05410.1016/j.conbuildmat.2018.12.054 ↗
32. Mannan, M. A., Alexander, J., Ganapathy, C., & Teo, D. C. L. (2006). Quality improvement of oil palm shell (OPS) as coarse aggregate in lightweight concrete. Building and Environment, 41(9), 1239–1242. https://doi.org/10.1016/j.buildenv.2005.05.01810.1016/j.buildenv.2005.05.018 ↗
33. Michel, M., Georgin, J.-F., Ambroise, J., & Péra, J. (2011). The influence of gypsum ratio on the mechanical performance of slag cement accelerated by calcium sulfoaluminate cement. Construction and Building Materials, 25, 1298–1304. https://doi.org/10.1016/j.conbuildmat.2010.09.01510.1016/j.conbuildmat.2010.09.015 ↗
34. Mikhailova, O., del Campo, A., Rovnanik, P., Fernández, J. F., & Torres-Carrasco, M. (2019). In situ characterization of main reaction products in alkali-activated slag materials by confocal raman microscopy. Cement and Concrete Composites, 99, 32–39. https://doi.org/10.1016/j.cemconcomp.2019.02.00410.1016/j.cemconcomp.2019.02.004 ↗
35. Moukwa, M., Youn, D., & Hassanali, M. (1993). Effects of degree of polymerization of water soluble polymers on concrete properties. Cement and Concrete Research, 23(1), 122–130. https://doi.org/10.1016/0008-8846(93)90142-V10.1016/0008-8846(93)90142-V ↗
36. Morlat, R., Orange, G., & Bomal, Y. (2007). Reinforcement of hydrated portland cement with high molecular mass water-soluble polymers. Journal of Materials Science, 42, 4858–4869. https://doi.org/10.1007/s10853-006-0645-z10.1007/s10853-006-0645-z ↗
37. Nguyen, D. D., Devlin, L. P., Koshy, P., & Sorrell, C. C. (2015). Effect of polyvinyl alcohol on rheology of portland cement pastes. Journal of the Australian Ceramic Society, 51, 23–28.
38. Nguyen, D. D., Devlin, L. P., Koshy, P., & Sorrell, C. C. (2016). Effects of chemical nature of polyvinyl alcohol on early hydration of Portland cement. Journal of Thermal Analysis Calorimetry, 123, 1439–1450. https://doi.org/10.1007/s10973-015-0576-010.1007/s10973-015-0576-0 ↗
39. Nigro, L., Magni, S., Ortenzi, M. A., Gazzotti, S., Torre, C. D., & Binelli, A. (2022). Are “liquid plastics” a new environmental threat? The case of polyvinyl alcohol. Aquatic Toxicology, 248, Article 106200. https://doi.org/10.1016/j.aquatox.2022.10620010.1016/j.aquatox.2022.106200 ↗
40. Ohama, Y. (1998). Polymer-based admixtures. Cement and Concrete Composites, 20(2–3), 189–212. https://doi.org/10.1016/S0958-9465(97)00065-610.1016/S0958-9465(97)00065-6 ↗
41. Pique, T. M., & Vazquez, A. (2013). Control of hydration rate of polymer modified cements by the addition of organically modified montmorillonites. Cement and Concrete Composites, 37, 54–60. https://doi.org/10.1016/j.cemconcomp.2012.12.00610.1016/j.cemconcomp.2012.12.006 ↗
42. Pooni, J., Robert, D., Giustozzi, F., Setunge, S., Xie, Y. M., & Xia, J. (2020). Novel use of calcium sulfoaluminate (CSA) cement for treating problematic soils. Construction and Building Materials, 260, Article 120433. https://doi.org/10.1016/j.conbuildmat.2020.12043310.1016/j.conbuildmat.2020.120433 ↗
43. Qua, E. H., Hornsby, P. R., Sharma, H. S. S., Lyons, G., & McCall, R. D. (2009). Preparation and characterization of poly(vinyl alcohol) nanocomposites made from cellulose nanofibers. Journal of Applied Polymer Science, 113(4), 2238–2247. https://doi.org/10.1002/app.3011610.1002/app.30116 ↗
44. Rashad, A. M. (2016). A synopsis about perlite as building material – a best practice guide for civil engineer. Construction and Building Materials, 121, 338–353. https://doi.org/10.1016/j.conbuildmat.2016.06.00110.1016/j.conbuildmat.2016.06.001 ↗
45. Santos, R. S., Rodrigues, F. A., Segre, N., & Joekes, I. (1999). Macro-defect free cements influence of poly(vinyl alcohol), cement type, and silica fume. Cement and Concrete Research, 29(5), 747–751. https://doi.org/10.1016/S0008-8846(99)00070-810.1016/S0008-8846(99)00070-8 ↗
46. Sengul, O., Azizi, S., Karaosmanoglu, F., & Tasdemir, M. A. (2011). Effect of expanded perlite on the mechanical properties and thermal conductivity of lightweight concrete. Energy and Buildings, 43(2–3), 671–676. https://doi.org/10.1016/j.enbuild.2010.11.00810.1016/j.enbuild.2010.11.008 ↗
47. Shaulov, A. Y., Lomakin, S. M., Zarkhina, T. S., Rakhimkulov, A. D., Shilkina, N. G., Muravlev, Y. B., & Berlin, A. A. (2005). Carbonization of poly(vinyl alcohol) in blends with boron polyoxide. Doklad Physical Chemistry, 403, 154–158. https://doi.org/10.1007/s10634-005-0048-x10.1007/s10634-005-0048-x ↗
48. Shi, Z., Geiker, M. R., DeWeerdt, K., Østnor, T. A., Lothenbach, B., Winnefeld, F., & Skibsted, J. (2017). Role of calcium on chloride binding in hydrated Portland cement–metakaolin–limestone blends. Cement and Concrete Research, 95, 205–216. https://doi.org/10.1016/j.cemconres.2017.02.00310.1016/j.cemconres.2017.02.003 ↗
49. Singh, N. B., & Rai, S. (2001). Effect of polyvinyl alcohol on the hydration of cement with rice husk ash. Cement and Concrete Research, 31(2), 239–243. https://doi.org/10.1016/S0008-8846(00)00475-010.1016/S0008-8846(00)00475-0 ↗
50. Singh, N. K., Mishra, P. C., Singh, V. K., & Narang, K. (2003). Effects of hydroxyethyl cellulose and oxalic acid on the properties of cement. Cement and Concrete Research, 33(9), 1319–1329. https://doi.org/10.1016/S0008-8846(03)00060-710.1016/S0008-8846(03)00060-7 ↗
51. Tarnowiecka-Kuca, A., Peeters, R., Bamps, B., Stobińska, M., Kamola, P., Wierzchowski, A., Bartkowiak, A., & Mizielińska, M. (2023). Paper coatings based on Polyvinyl alcohol and cellulose nanocrystals using various coating techniques and determination of their barrier properties. Coatings, 13, 1975. https://doi.org/10.3390/coatings1311197510.3390/coatings13111975 ↗
52. Thong, C. C., Teo, D. C. L., & Ng, C. K. (2016). Application of polyvinyl alcohol (PVA) in cement-based composite materials: A review of its engineering properties and microstructure behavior. Construction and Building Materials, 107, 172–180. https://doi.org/10.1016/j.conbuildmat.2015.12.18810.1016/j.conbuildmat.2015.12.188 ↗
53. Topic, J., Prošek, Z., Indrová, K., Plachý, T., Nežerka, V., Kopecký, L., & Tesárek, P. (2015) Effect of PVA modification on the properties of cement of composites, Acta Polytechnica, 55(1), 64–75. https://doi.org/10.14311/AP.2015.55.006410.14311/AP.2015.55.0064 ↗
54. Tran, N. P., Gunasekara, C., Law, D. W., Houshyar, S., & Setunge, S. (2022). Microstructural characterisation of cementitious composite incorporating polymeric fiber: A comprehensive review. Construction and Building Materials, 335, Article 127497. https://doi.org/10.1016/j.conbuildmat.2022.12749710.1016/j.conbuildmat.2022.127497 ↗
55. Vassileva, C. G., & Vassilev, S. V. (2005). Behaviour of inorganic matter during heating of Bulgarian coals: 1. Lignites, Fuel Processing Technology, 86, 1297–1333. https://doi.org/10.1016/j.fuproc.2005.01.02410.1016/j.fuproc.2005.01.024 ↗
56. Viswanath, P., & Thachil, E. T. (2008). Properties of polyvinyl alcohol cement pastes. Materials and Structures, 41, 123–130. https://doi.org/10.1617/s11527-007-9224-210.1617/s11527-007-9224-2 ↗
57. Wiśniewska, M., Chibowski, S., Urban, T., & Sternik, D. (2011). Investigation of the alumina properties with adsorbed polyvinyl alcohol. Journal of Thermal Analysis and Calorimetry, 103, 329–337. https://doi.org/10.1007/s10973-010-1040-110.1007/s10973-010-1040-1 ↗
58. Wu, K., Han, H., Xu, L., Gao, Y., Yang, Z., Jiang, Z., & De Schutter, G. (2021). The improvement of freezing–thawing resistance of concrete by cellulose/polyvinyl alcohol hydrogel. Construction and Building Materials, 291, Article 123274. https://doi.org/10.1016/j.conbuildmat.2021.12327410.1016/j.conbuildmat.2021.123274 ↗
59. Xing, Y., & Wang, B. (2023). Effect of the chemical nature of polyvinyl alcohol on the microstructure of cement hydration products. Journal of Materials in Civil Engineering. https://doi.org/10.1061/JMCEE7.MTENG-1424910.1061/JMCEE7.MTENG-14249 ↗
60. Yao, J., Ge, Y., Ruan, W., & Meng, J. (2024). Effects of PVA fiber on shrinkage deformation and mechanical properties of ultra-high performance concrete. Construction and Building Materials, 417, Article 135399. https://doi.org/10.1016/j.conbuildmat.2024.13539910.1016/j.conbuildmat.2024.135399 ↗
61. Ylmén, R., & Jäglid, U. (2013). Carbonation of Portland cement studied by diffuse reflection Fourier transform infrared spectroscopy. International Journal of Concrete Structures and Materials, 7(2), 119–125. https://doi.org/10.1007/s40069-013-0039-y10.1007/s40069-013-0039-y ↗
62. Zhang, T., Tian, W., Guo, Y., Bogush, A., Khayrulina, E., Wei, J., & Yu, Q. (2019). The volumetric stability, chloride binding capacity and stability of the Portland cement-GBFS pastes: An approach from the viewpoint of hydration products. Construction and Building Materials, 205, 357–367. https://doi.org/10.1016/j.conbuildmat.2019.02.02610.1016/j.conbuildmat.2019.02.026 ↗
63. Zhang, J., Zhang, N., Li, C., & Zhang, Y. (2021). Strength development mechanism of a marine binding material with red mud and seawater. Construction and Building Materials, 303, Article 124428. https://doi.org/10.1016/j.conbuildmat.2021.12442810.1016/j.conbuildmat.2021.124428 ↗
64. Zhao, C., Wang, Z., Zhu, Z., Guo, Q., Wu, X., & Zhao, R. (2023). Research on different types of fiber reinforced concrete in recent years: An overview. Construction and Building Materials, 365, Article 130075. https://doi.org/10.1016/j.conbuildmat.2022.13007510.1016/j.conbuildmat.2022.130075 ↗