journal article·2022-03

A Model correlating fluidity to alloy variables in hypoeutectic alloys

Q. Han

Acta Materialia· Volume 226
Publisher page

Abstract

Mechanisms by which flow is choked are described. A criterion function for the choke of flow is proposed based on Darcy`s law. Simple mathematical equations are derived to correlate grain size of an alloy to the permeability of its mushy zone, which is a function of the critical volume fraction of solid, gC, at which the flow is choked. Such a correlation gives rise to a simple analytical equation of gC to grain size. A two-parameter equation correlating grain size to phase diagram variables is then used in the analytical equations to describe fluidity as function of alloy variables. Experimental results obtained in well-controlled experiments are used to validate analytical relationships. Model predictions fit experimental data reasonably well. These simple analytical models indicate that fluidity decreases monotonically with increasing solidification interval of an alloy or modified constitutional supercooling parameter which is a function of liquidus slope, partition coefficient, and alloy composition.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Metallurgical Processes and Thermodynamics · Solidification and crystal growth phenomena

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. J. Campbell. Casting, Butterworth-Heinemann, 2000, p. 74.
2. A Few Method for Determining the Effect of Solidification Range on Fluidity
3. Fluidity of Metals – Techniques for Producing Ultra-Thin Section Castings
4. Fluidity of Aluminum Alloys
5. Fluidity of a Series of Magnesium Alloys
6. Some Factors Affecting Fluidity of Metals
7. Fluidity of Alloys under High Pressure Die Casting Conditions10.1016/j.scriptamat.2005.03.025 ↗
8. Fluidity of Aluminum Die Casting Alloy10.1179/136404608X286110 ↗
9. Fluidity of Aluminum Alloys and Composites: a Review10.1016/j.jallcom.2007.02.038 ↗
10. B. Dewhirst. Castability Control in Metal Casting via Fluidity Measures: application of Error Analysis to Variations in Fluidity Testing, Ph.D. Dissertation, Worcester Polytechnic Institute, 2008.
11. Predicting Flow Length in Die Casting Including Heat Advection
12. Equation Model to Evaluate Fluidity of Aluminum Alloys under Pressure Die-casting Conditions with an Application10.4028/www.scientific.net/AMR.505.190 ↗
13. Fluidity from a Heat Transfer Perspective
14. The Gating Equation Updated
15. Fluidity of Alloys under High-Pressure Die Casting Conditions: flow-Choking Mechanisms10.1007/s11663-020-01858-0 ↗
16. Grain Refining of Aluminum and Its Alloys Using Inoculants10.1179/imr.1989.34.1.247 ↗
17. Fluid Flow through Granular Beds
18. Measurement of Liquid Permeability in the Mushy Zones of Aluminum-Copper Alloys10.1007/s11663-999-0036-3 ↗
19. On the Origin of Equiaxed Zone in Castings
20. Origin of the Equiaxed Crystals in Castings10.2355/isijinternational1966.11.18 ↗
21. A Simple Model for Grain Refinement during Solidification10.1016/0001-6160(75)90188-1 ↗
22. Solute Diffusion Model for Equiaxed Dendritic Growth10.1016/0001-6160(87)90094-0 ↗
23. Cooling-Assisted Ultrasonic Grain Refining of Aluminum E380 Die Casting Alloy
24. Revisit the Role of Solutes in Grain Refinement of Hypoeutectic Alloys10.1007/s11661-021-06382-7 ↗
25. Effect of Solute Content on the Grain Refinement of Binary Alloys10.1007/BF01160574 ↗
26. Effect of the Alloy Composition on the Grain Refinement of Aluminum Alloys10.1016/j.scriptamat.2006.02.035 ↗
27. The Influence of Composition on Equiaxed Crystal Growth Mechanisms and Grain Size in Al Alloys
28. Effect of Solute Si and Cu on Grain Size of Aluminum Alloys10.1179/1743133612Y.0000000023 ↗
29. A New Model of Growth Restriction Factor for Hypoeutectic Aluminum Alloys10.1016/j.scriptamat.2020.01.009 ↗
30. Effect of Alloy Variables on Grain Refinement of Binary Aluminum Alloys with Al-Ti-B10.1179/mst.1995.11.6.533 ↗
31. Experiments on the Solidification Structure of Alloy Castings10.1007/BF02814899 ↗
32. A Parameter for Evaluating Ability of Grain Refinement of Solute Elements
33. Modeling of Inoculation of Metallic Melts: application to Grain Refinement of Aluminium by Al-Ti-B10.1016/S1359-6454(00)00094-X ↗
34. A Model of Grain Refinement Incorporating Alloy Constitution and Potency of Heterogeneous Nucleant Particles10.1016/S1359-6454(00)00368-2 ↗
35. Metastable Phase Equilibria in the Lead-Tin Alloy System: part II. Thermodynamic Modeling10.1007/BF02651646 ↗
36. Microstructure and properties of Mg-Al binary alloys