journal article·2024-11-01Open access

Analysis of Changes in the Stress–Strain State and Permeability of a Terrigenous Reservoir Based on a Numerical Model of the Near-Well Zone with Casing and Perforation Channels

Sergey Chernyshov, Sergey Popov, Xiaopu Wang, Vadim Derendyaev, Yongfei Yang, Huajie Liu

Applied Sciences· Volume 14· Issue 21

Abstract

A finite element model, which includes reservoir rock, cement stone, casing, and perforation channels, was developed. The purpose of the study is to create a geomechanical model of the zone around the well, which includes support elements and perforation channels. This model will help predict changes in the productivity coefficient of a terrigenous reservoir and determine the most efficient mode of operation of a producing well. In order to exclude the stress concentration within the casing–cement stone and cement stone–rock, the numerical model applies contact elements. As a result, structural elements slip, while the stresses are redistributed accurately. The numerical simulation of a stress state in the near-well zone was carried out by using the developed model with differential pressure drawdown on the terrigenous reservoir, one of the oil fields in the Perm region. It is shown that the safety factor of the casing reaches roughly 3–4 units. The only exceptions are the upper and lower parts of the perforations, where this parameter is close to one unit. The safety factor of cement stone accounts for 2–3 units. However, parts with its lowest value (1.35) are also concentrated near the perforation channels. In order to analyze the change in permeability, the dependence of the safety factor on effective stresses was taken into account. Therefore, it was found that, in the upper and lower parts of perforations, the stresses decreased, while permeability rose by up to 20% of the initial value. An increase in differential pressure drawdown, on the contrary, can lead to a permeability reduction of 25%, especially in the lateral parts of the perforations. Areas of rock destruction under tensile and compressive forces were identified by using the Mohr–Coulomb criterion. It is estimated that with an increase in pressure drawdown, the areas of rock destruction under tensile force disappear, while the areas of rock destruction under compression increase. After further analysis, it was found that, with the maximum pressure drawdown of 12 MPa, the well productivity index can decrease by 15% due to the reservoir rock compaction.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Hydraulic Fracturing and Reservoir Analysis · Drilling and Well Engineering · Geological Studies and Exploration

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Oil and Gas Technologies Department, Perm National Research Polytechnic University, 614990 Perm, Russia

Institute of Oil and Gas Problems of the Russian Academy of Sciences, 119333 Moscow, Russia

School of Petroleum Engineering, China University of Petroleum, Qingdao 266580, China

Funding

state task “Experimental and theoretical studies of interfacial phenomena, thermodynamic, physicochemical and geomechanical properties of oil and gas reservoir systems to improve the efficiency of development of hard-to-recover hydrocarbon reserves”

References (23)

Show source-provided references
1. Zoback, M.D. (2007). Reservoir Geomechanics, Cambridge University Press.10.1017/CBO9780511586477 ↗
2. Fjear, E., Holt, R.M., Horsrud, P., Raaen, A.M., and Risnes, R. (2008). Petroleum Related Rock Mechanics, Elsevier.
3. Kashnikov, Y.U.A., and Ashihmin, S.G. (2007). Mechanics of Rocks in the Development of Hydrocarbon Deposits, OOO «Nedra Biznes-Centr».
4. Ma, T., Liu, J., Fu, J., Qiu, Y., Fan, X., and Martyushev, D.A. (2024). Fully Coupled Thermo-hydro-mechanical Model for Wellbore Stability Analysis in Deep Gas-Bearing Unsaturated Formations Based on Thermodynamics. Rock Mech. Rock Eng.10.1007/s00603-023-03703-7 ↗
5. Borehole stability prediction to avoid drilling failures
6. Development of integrated geomechanical modeling in “Gazprom neft” PJSC
7. Development of a geomechanical model and determination of the drilling fluid “density window” in the interval of famennian productive deposits (on the example of a site of one of the Timano-Pechora oil and gas province oilfield)
8. Wang, L., Shen, X., Wu, B., Shen, T., and Shi, J. (2023). Integrated analysis of the 3D geostress and 1D geomechanics of an exploration well in a new gas field. Energies, 16.10.3390/en16020806 ↗
9. Increasing efficiency of hydrocarbon fields development based on complex geomechanical research
10. Yang, Y., Liu, Z., Sun, Z., An, S., Zhang, W., Liu, P., Yao, J., and Ma, J. (2017). Research on Stress Sensitivity of Fractured Carbonate Reservoirs Based on CT Technology. Energies, 10.10.3390/en10111833 ↗
11. Developing features of the near-bottomhole zones in productive formations at fields with high gas saturation of formation oil10.31897/PMI.2021.3.7 ↗
12. Acid fracturing technology and effect evaluation of carbonate horizontal well in Fuman oilfield10.1088/1742-6596/2679/1/012010 ↗
13. Liu, F., Fan, Y., Li, L., Li, J., Chen, Y., Lv, Z., and He, T. (2022). Case study of successfully staged acid fracturing on the ultra-deep horizontal well for the Qixia fm HTHP tight carbonate gas reservoir in China. Front. Energy Res., 10.10.3389/fenrg.2022.917740 ↗
14. Safari, R., Smith, C., and Fragachan, F. (2017, January 13). Improved Recovery of Carbonate Reservoir by Optimizing Acidizing Strategy: Coupled Wellbore, Reservoir, and Geomechanical Analysis. Proceedings of the Abu Dhabi International Petroleum Exhibition & Conference, Abu Dhabi, United Arab Emirates.10.2118/188683-MS ↗
15. Al-Awad, M.N.J., and Al-Ahaidib, T.Y. (2005, January 14). Estimating the amount of free sand in the yielded zone around horizontal oil wells. Proceedings of the SPE Technical Symposium of Saudi Arabia Section, Dhahran, Saudi Arabia.10.2523/106329-MS ↗
16. Araujo-Guerrero, E.F., Alzate-Espinosa, G.A., Arbelaez-Londono, A., Pena Clavijo, S., and Cardona Ramirez, A. (2014, January 24). Analytical prediction model of sand production integrating geomechanics for open hole and cased—perforated wells. Proceedings of the SPE Heavy and Extra Heavy Oil Conference, Latin America, Medellín, Colombia.10.2118/171107-MS ↗
17. Estimation of the maximum downhole pressure, excluding the destruction of the bottom-hole zone of the formation, based on geomechanical core studies
18. Analysis of wells cement sheath stability during shaped charge perforating based on geomechanical modeling10.18599/grs.2023.2.18 ↗
19. Fallahzadeh, S.H., and Shasizadeh, S.R. (2010, January 31). Modeling the Perforation Stress Profile for Analyzing Hydraulic Fracture Initiation in a Cased Hole. Proceedings of the Nigeria Annual International Conference and Exhibition, Tinapa, Calabar, Nigeria.10.2118/136990-MS ↗
20. Modelling the stress-strain state change of near-wellbore area and its reservoir properties during drilling
21. Comparative analysis of the analytical and numerical methods for calculating the stress-strain state of the near-wellbore zone based on the elastic model taking into account the main structural elements of the well10.18799/24131830/2023/5/3961 ↗
22. Message passing interface (MPI) parallelization of iteratively coupled fluid flow and geomechanics codes for the simulation of system behavior in hydrate-bearing geological media. Part 1: Methodology and validation10.2118/206161-PA ↗
23. Transportation of cuttings by drilling mud in horizontal wells. Part 2. Numerical results of drilling at optimal rheological properties of mud10.18799/24131830/2023/11/4468 ↗