journal article·2020-09

Dynamic mechanical analysis of carbon black filled, elastomer-toughened ethyl cyanoacrylate adhesive bulk films

Tatiana Ștefanov, Bernard Ryan, Alojz Ivanković, Neal Murphy

Publisher page

Abstract

Abstract This paper reports on a dynamic mechanical analysis (DMA) study of carbon black filled, elastomer-toughened ethyl cyanoacrylate (ETECA) adhesive bulk films. The bulk films were cured at room temperature, both with and without premixed initiators, between poly (ethylene) (PE) substrates and in poly (tetrafluoroethylene) (PTFE) moulds. Adhesive batches with different strong and weak acid concentrations were used to study the influence of the curing speed on the phase separation behaviour of the elastomer. The mechanical properties of the bulk adhesive films and electron micrographs of the fracture surface of the tensile tested bulk specimens are reported in the previous publication by Ștefanov et al. [1; International Journal of Adhesion & Adhesives, 68: 142–155, 2016]. For all tested bulk adhesive films similar peaks were observed in the DMA curves, i.e., a peak at low temperature, before the glass transition region of the polymer, and a peak corresponding to the glass transition temperature of the poly (cyanoacrylate) adhesive. The results of this investigation show that the amount of the phase-separated elastomer increases with the increase in weak acid concentration for the samples cured without the use of initiators. An opposite trend was observed for the samples cured using initiators. Another important finding is that for a complete phase-separation of the elastomer from the poly CA a secondary step, following curing at room temperature, is necessary which should consist of heating the sample to 110 °C.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Epoxy Resin Curing Processes · Injection Molding Process and Properties · Dental materials and restorations

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (21)

Show source-provided references
1. Mechanical bulk properties and fracture toughness of composite-to-composite joints of an elastomer-toughened ethyl cyanoacrylate adhesive10.1016/j.ijadhadh.2016.03.001 ↗
2. Determination of absolute rate constants for radical polymerisation and copolymerisation of ethyl α-cyanoacrylate in the presence of effective inhibitors against anionic polymerisation10.1002/macp.1983.021840514 ↗
3. Coover · 1990 · 463
4. J.T. O'Connor. Toughened cyanoacrylates containing elastomeric rubbers, April 3 1984. US Patent 4,440,910.
5. G.H. Millet, E.R. Harrell, and C.D. Wright. Cyanoacrylate adhesive composition having sustained toughness, December 24 1985. US Patent 4,560,723.
6. Toughened cyanoacrylate adhesives containing alkene-acrylate copolymers and method for production
7. M. Mitry. Toughened cyanoacrylate adhesive composition containing polyester polymers, August 23 1994. US Patent 5,340,873.
8. H.R. Misiak. Toughened cyanoacrylate compositions, March 30 2010. US Patent 7,687,561.
9. Rubber-filler interactions and rheological properties in filled compounds10.1016/S0079-6700(01)00040-5 ↗
10. Kroschwitz · 2004 · vol. 9 · 52
11. Polymerisation via macrozwitterions, 2. ethyl and butyl cyanoacrylates polymerized by pyridine and polyvinylpyridine10.1002/macp.1981.021820212 ↗
12. Termination and transfer by acids in the pyridine-initiated polymerisation of butyl cyanoacrylate10.1016/0014-3057(83)90053-8 ↗
13. Menard · 2008
14. 2012
15. 2012
16. Rubber modified epoxy resin. II: phase separation behavior10.1002/pen.760342104 ↗
17. Yu · 2015 · 1
18. Toughness of syndiotactic polystyrene/epoxy polymer blends: microstructure and toughening mechanisms10.1016/j.polymer.2005.05.151 ↗
19. Phase separation behaviour of rubber-modified epoxies10.1002/app.1981.070260725 ↗
20. Reaction-induced phase decomposition in polymer blends10.1016/0079-6700(94)00032-W ↗
21. Cure kinetics, morphology and miscibility of modified DGEBA-based epoxy resin-Effects of a liquid rubber inclusion10.1016/j.polymer.2007.01.018 ↗