Enhancement of Primary Profile Surface Quality in FFF Printing Through Vibration Monitoring and Active Control
Source abstract
Abstract
Vibrations of the print head and structural components during 3D printing with FFF technology can significantly impact the quality of printed parts, resulting in defects such as ghosting, ringing, and geometric inaccuracies. These undesired effects are primarily caused by mechanical oscillations of the print head, build platform, and frame, induced by dynamic changes in movement speed and inertial forces within the printing mechanism. This study investigates the effectiveness of vibration compensation using an ADXL345 accelerometer to regulate the motion of the print head and build platform on the Ender 3 V2 Neo printer. The experiment consisted of three test series performed under two distinct conditions, without vibration compensation and with active compensation enabled. All tests were carried out using identical baseline printing parameters. The differences in output were evaluated through visual inspection and dimensional analysis of the printed samples. Efficient vibration monitoring and its active control, aimed at suppressing oscillatory phenomena, can enhance both geometric accuracy and surface uniformity. In FFF 3D printing, especially when utilizing increased layer heights such as 0.3 mm, surface roughness (Ra) values in the range of 18 to 25 µm are typically expected, even when optimal process parameters are applied. This study emphasizes the role of active vibration control strategies in additive manufacturing, particularly in enhancing surface quality and dimensional accuracy. The objective is not only to mitigate the adverse effects of dynamic mechanical vibrations but also to determine the extent to which surface roughness can be systematically reduced under defined conditions, such as layer height, print speed, and movement trajectory. The aim is to improve the final product quality without introducing significant compromises in process efficiency.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Industrial Vision Systems and Defect Detection · Material Properties and Processing · Surface Roughness and Optical Measurements
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Computer Aided Manufacturing Technologies, Faculty of Manufacturing Technologies with a Seat in Presov, Technical University of Kosice, Bayerova 1, 08001 Presov, Slovakia
References (26)
Show source-provided references
1. Effect of nozzle vibration at different frequencies on surface structures and tensile properties of PLA parts printed by FDM10.1016/j.matlet.2022.132612 ↗
2. Base vibration effects on additive manufactured part quality10.1007/s40799-023-00629-1 ↗
3. Zaidi, S., Viswanathan, V., Santosh, K.C., Ravada, S., and Vyas, A. (2024, January 17–21). Comparison of Vibrational Impacts on Tensile Strength in 3D Printing Materials. Proceedings of the ASME International Mechanical Engineering Congress and Exposition, Portöand, OR, USA.10.1115/IMECE2024-145575 ↗
4. Study on Dynamic Behaviour in FFF 3D-printing with Crossed Gantry Kinematic10.1016/j.procir.2023.09.244 ↗
5. Comparative study of vibration signatures of FDM 3D printers10.1007/s40964-022-00323-5 ↗
6. Impact of 3d printer vibration reduction on the quality of its printout
7. General Methodology to Investigate the Effect of Process Parameters on the Vibration Properties of Structures Produced by Additive Manufacturing Using Fused Filament Fabrication10.1007/s11837-021-05051-9 ↗
8. Li, Y., Zhao, W., Li, Q., Wang, T., and Wang, G. (2019). In-situ monitoring and diagnosing for fused filament fabrication process based on vibration sensors. Sensors, 19.10.3390/s19112589 ↗
9. Waheed, M.F., and Bernadin, S. (2024, January 21–24). In-Situ Analysis of Vibration and Acoustic Data in Additive Manufacturing. Proceedings of the SoutheastCon 2024, Atlanta, GA, USA.10.1109/SoutheastCon52093.2024.10500055 ↗
10. Isiani, A., Weiss, L., Bardaweel, H., Nguyen, H., and Crittenden, K. (2023). Fault detection in 3D printing: A study on sensor positioning and vibrational patterns. Sensors, 23.10.3390/s23177524 ↗
11. Erokhin, K., Naumov, S., and Ananikov, V. (2023). Defects in 3D Printing and Strategies to Enhance Quality of FFF Additive Manufacturing. A Review. ChemRxiv.10.26434/chemrxiv-2023-lw1ns ↗
12. Pilch, Z., Domin, J., and Szłapa, A. (2015, January 17–19). The impact of vibration of the 3D printer table on the quality of print. Proceedings of the 2015 Selected Problems of Electrical Engineering and Electronics (WZEE), Kielce, Poland.10.1109/WZEE.2015.7394045 ↗
13. The influence of 3D printing process parameters on the mechanical performance of PLA polymer and its correlation with hardness10.1016/j.promfg.2021.07.038 ↗
14. Zhen, H., Zhao, B., Quan, L., and Fu, J. (2023). Effect of 3D printing process parameters and heat treatment conditions on the mechanical properties and microstructure of PEEK parts. Polymers, 15.10.3390/polym15092209 ↗
15. Quality control issues in 3D-printing manufacturing: A review10.1108/RPJ-02-2017-0031 ↗
16. Li, G., Zhao, J., Wu, W., Jiang, J., Wang, B., Jiang, H., and Fuh, J.Y.H. (2018). Effect of ultrasonic vibration on mechanical properties of 3D printing non-crystalline and semi-crystalline polymers. Materials, 11.10.3390/ma11050826 ↗
17. Kopets, E.E., Kolev, G.Y., Vatnik, V.M., Karimov, A.I., and Rybin, V.G. (2021, January 26–28). Mechanical vibration analysis of a gantry 3D printer. Proceedings of the 2021 IEEE Conference of Russian Young Researchers in Electrical and Electronic Engineering (ElConRus), Moscow, Russia.10.1109/ElConRus51938.2021.9396599 ↗
18. Theoretical study of the interactions between vibrations of large numbers of FDM 3D printers10.1007/s40964-023-00438-3 ↗
19. Kasprowiak, M., Parus, A., and Hoffmann, M. (2022). Vibration suppression with use of input shaping control in machining. Sensors, 22.10.3390/s22062186 ↗
20. A new trajectory optimizing method using input shaping principles10.1155/2018/4173253 ↗
21. Li, T., and Xiao, T. (2025). Physics-Informed Neural Network-Based Input Shaping for Vibration Suppression of Flexible Single-Link Robots. Actuators, 14.10.3390/act14010014 ↗
22. Grazioso, S., Di Gironimo, G., Singhose, W., and Siciliano, B. (2017, January 27–30). Input predictive shaping for vibration control of flexible systems. Proceedings of the 2017 IEEE Conference on Control Technology and Applications (CCTA), Mauna Lani Resort, HI, USA.10.1109/CCTA.2017.8062480 ↗
23. Optimization of FDM 3-D printer process parameters for surface roughness and mechanical properties using PLA material10.1016/j.matpr.2022.05.422 ↗
24. Evaluation of the surface roughness and dimensional accuracy of low-cost 3D-printed parts made of PLA–aluminum10.1016/j.heliyon.2024.e25508 ↗
25. Olejárová, Š., Ružbarský, J., and Krenický, T. (2019). Vibrations in the Production System: Measurement and Analysis with Water Jet Technology, Springer International Publishing.10.1007/978-3-030-01737-8 ↗
26. Mitaľ, G., Dobránsky, J., Ružbarský, J., and Olejárová, Š. (2019). Application of laser profilometry to evaluation of the surface of the workpiece machined by abrasive waterjet technology. Appl. Sci., 9.10.3390/app9102134 ↗