Investigation on solid particles erosion resistance of laser cladded CoCrFeNiTi high entropy alloy coating
Source abstract
Abstract
Abstract High entropy alloy (HEA) as coating material has more economical application value. In this study, CoCrFeNiTi HEA coating without cracks and pores was successfully prepared on 304 stainless steel substrate by laser cladding. The phase structure of the CoCrFeNiTi HEA coating was composed of main phase with an FCC lattice, Fe and Cr rich phase with an SC lattice and CoTi2 type Laves phase. The microstructure of the prepared coating consisted of bonding zone and cladding zone. It was an obviously metallurgical bonding between the coating and substrate and typical columnar dendrites were generated with growth direction perpendicular to the interface in the bonding zone. The cladding zone showed a typical long strip proeutectic structure and a lamellar eutectic structure. The average microhardness of CoCrFeNiTi HEA coating reached to 568 HV0.2, which was approximately 2.5 times higher than that of the substrate (236 HV0.2). Erosion tests were conducted on both CoCrFeNiTi HEA coatings and the substrates with an erosion angle of 30 and 90°. The results showed that CoCrFeNiTi HEA coating exhibited much lower erosion rates with an erosion angle of 30° (0.68 mg/cm2) and 90° (0.42 mg/cm2). Ploughing and micro-cutting were the two primary erosion mechanisms of material loss for CoCrFeNiTi HEA coating at oblique erosion angles, while the erosion mechanism was replaced by the formation of craters at vertical erosion angles.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Entropy Alloys Studies · High-Temperature Coating Behaviors · Additive Manufacturing Materials and Processes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. New Fe-based soft magnetic amorphous alloys with high saturation magnetization and good corrosion resistance for dust core application10.1016/j.intermet.2016.05.011 ↗
2. Optimizing the microstructures and mechanical properties of Al-Cu-based alloys with large solidification intervals by coupling travelling magnetic fields with sequential solidification10.1016/j.jmst.2020.05.048 ↗
3. Effect of a small increase in the Ni content on the properties of a laser surface clad Fe-based alloy10.1016/j.apsusc.2006.09.068 ↗
4. Nanostructured high-entropy alloys with multiple principal elements: novel alloy design concepts and outcomes10.1002/adem.200300567 ↗
5. Formation condition of solid solution type high-entropy alloy10.1016/S1003-6326(13)62557-1 ↗
6. Prediction of high-entropy stabilized solid-solution in multi-component alloys10.1016/j.matchemphys.2011.11.021 ↗
7. Microstructures and properties of high-entropy alloys10.1016/j.pmatsci.2013.10.001 ↗
8. Effect of laser re-melting on electric current assistive sintered CoCrFeNiAlxTiy high entropy alloys: formation, micro-hardness and wear behaviors10.1016/j.surfcoat.2020.126179 ↗
9. Development of a new high entropy alloy for wear resistance: FeCoCrNiW0.3 and FeCoCrNiW0.3+ 5 at.% of C10.1016/j.matdes.2016.11.027 ↗
10. Homogenization of Al CoCrFeNi high-entropy alloys with improved corrosion resistance10.1016/j.corsci.2018.01.030 ↗
11. Improvement of high temperature oxidation resistance of micro arc oxidation coated AlTiNbMo0.5Ta0.5Zr high entropy alloy10.1016/j.matlet.2019.127192 ↗
12. Direct solidification of bulk ultrafine-microstructure eutectic high-entropy alloys with outstanding thermal stability10.1016/j.scriptamat.2019.02.035 ↗
13. Effects of ultrasonic impact treatment on structures and properties of laser cladding Al0.5CoCrFeMnNi high entropy alloy coatings10.1016/j.matchemphys.2020.123850 ↗
14. Microstructure and properties of TiNbZrMo high entropy alloy coating
15. The relationship between thermo-mechanical history, microstructure and mechanical properties in additively manufactured CoCrFeMnNi high entropy alloy10.1016/j.jmst.2020.10.052 ↗
16. Microstructure and wear behavior of mechanically alloyed powder AlxMo0.5NbFeTiMn2 high entropy alloy coating formed by laser cladding10.1016/j.surfcoat.2020.126244 ↗
17. Effect of Fe on microstructure and properties of AlCoCrFexNi (x=1.5, 2.5) high entropy alloy coatings prepared by laser cladding10.1016/j.intermet.2020.106722 ↗
18. MoFe1.5CrTiWAlNbx refractory high-entropy alloy coating fabricated by laser cladding10.1016/j.intermet.2019.106613 ↗
19. Effect of Mn and V on structure and mechanical properties of high-entropy alloys based on CoCrFeNi system10.1016/j.jallcom.2013.12.210 ↗
20. Microstructural evolution, electrochemical and corrosion properties of AlCoCrFeNiTi high entropy alloys10.1016/j.matdes.2019.107698 ↗
21. Annealing effects on the microstructure and properties of bulk high-entropy CoCrFeNiTi0.5 alloy casting ingot10.1016/j.intermet.2013.08.016 ↗
22. CoCrFeNiTi-based high-entropy alloy with superior tensile strength and corrosion resistance achieved by a combination of additive manufacturing using selective electron beam melting and solution treatment10.1016/j.matlet.2016.11.026 ↗
23. High temperature erosion properties of arc-sprayed coatings using various cored wires containing Ti–Al intermetallics10.1016/j.wear.2006.06.021 ↗
24. High temperature erosion–oxidation of Cr3C2–NiCr thermal spray coatings under simulated turbine conditions10.1016/j.corsci.2013.01.030 ↗
25. Erosion behavior of arc sprayed FeTi/CrB MMC coating at elevated temperature10.1016/j.surfcoat.2014.12.027 ↗
26. Investigation on microstructure and properties of laser cladded AlCoCrCuFeNi high entropy alloy coating by ultrasonic impact treatment10.1016/j.intermet.2020.107017 ↗
27. Microstructure and tribological property of CoCrFeMoNi High entropy alloy treated by ion sulfurization10.1016/j.jmrt.2019.12.090 ↗
28. Sulfurizing of CoCrFeNiSi0.4 and CoCrFeMoNi high entropy alloys fabricated by laser cladding10.1016/j.surfcoat.2019.125182 ↗
29. Enhanced surface layers by laser cladding and ion sulfurization processing towards improved wear-resistance and self-lubrication performances10.1016/j.apsusc.2019.144226 ↗
30. Mechanical and corrosion properties of CoCrFeNiTi-based high-entropy alloy additive manufactured using selective laser melting10.1016/j.addma.2018.10.023 ↗
31. Microstructure and properties of CoCrFeNiTi high-entropy alloy coating fabricated by laser cladding10.1007/s11665-020-05204-y ↗
32. Coating fracture toughness determined by Vickers indentation: an important parameter in cavitation erosion resistance of WC–Co thermally sprayed coatings10.1016/S0257-8972(03)00917-4 ↗
33. Laser surface alloying of FeCoCrAlNi high-entropy alloy on 304 stainless steel to enhance corrosion and cavitation erosion resistance10.1016/j.optlastec.2016.04.011 ↗
34. Exceptionally high cavitation erosion and corrosion resistance of a high entropy alloy10.1016/j.ultsonch.2017.09.044 ↗
35. Simulation model for the erosion of brittle materials10.1016/S0043-1648(99)00180-5 ↗
36. An investigation of impingement erosion using single particles10.1016/0043-1648(72)90257-8 ↗
37. High temperature oxidation and erosion behaviour of HVOF sprayed bi-layer Alloy-718/NiCrAlY coating10.1016/j.surfcoat.2019.02.012 ↗