Mechanical, tribological and electrochemical corrosion properties of in-situ synthesized Al2O3/TiAl composites
Source abstract
Abstract
Abstract TiAl-based composites reinforced with different weight fractions of Al2O3 have been successfully synthesized by hot-pressing using the pre-alloyed Ti–45Al–7Nb-0.2B and Nb2O5 powders. The microstructures, mechanical and tribological properties of composites were examined. The as-sintered TiAl composites mainly consist of γ-TiAl phase, α2-Ti3Al phase, γ/α2 lamellar colony, TiB2 particles and Al2O3 particles. The microstructure can be refined by synthesizing Al2O3 particles. The volume fractions of α2 phase and α2/γ lamellar colonies increased with the increasing of Al2O3 content. When the Al2O3 content increases to 0.5 wt %, the composite exhibited the best comprehensive mechanical properties with the yield stress of 1032 ± 13 MPa and fracture strength of 2668 ± 15 MPa. For the Al2O3/TiAl composites, the fracture type is mainly composed of transgranular, translamellar and delamination fracture. The friction coefficient of 0.5 wt % Al2O3/TiAl composite is lower than other TiAl composites due to its homogeneous distribution of Al2O3 particles. The main wear mechanism of Al2O3/TiAl composites was determined to be abrasive wear along with plowing grooves. Addition of Al2O3 particles can improve the corrosion resistance of TiAl composites.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Intermetallics and Advanced Alloy Properties · Aluminum Alloys Composites Properties · MXene and MAX Phase Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (57)
Show source-provided references
1. Microstructural evolution and mechanical properties of Ti-5Al-5Mo-5V-3Cr alloy by heat treatment with continuous temperature gradient10.1016/S1003-6326(18)64660-6 ↗
2. Microstructure stability and micro-mechanical behavior of as-cast gamma-TiAl alloy during high-temperature low cycle fatigue10.1016/j.actamat.2017.12.040 ↗
3. Phase transformation and microstructural control of the α-solidifying γ-Ti-45Al-2Nb-0.7Cr-0.3Si intermetallic alloy10.1016/j.jallcom.2018.05.051 ↗
4. Microstructures and mechanical properties of directionally solidified C-containing γ-TiAl alloys via electromagnetic cold crucible10.1016/j.intermet.2019.106587 ↗
5. Microstructures and mechanical properties of TiAl alloys consolidated by spark plasma sintering10.1016/j.intermet.2008.06.015 ↗
6. Enhanced TiAl/Ti3SiC2 diffusion bonding by introducing amorphous intergranular films in Ti3SiC2 through Al doping10.1016/j.scriptamat.2019.12.031 ↗
7. Influence of Mo content on microstructure and mechanical properties of β-containing TiAl alloy10.1016/S1003-6326(17)60094-3 ↗
8. Microstructures evolution and mechanical properties of a powder metallurgical titanium alloy with yttrium addition10.1080/10426910903365778 ↗
9. Wear behavior of PM high Nb containing γ TiAl alloy in different environment
10. Nanomaterials in superlubricity10.1002/adfm.201806395 ↗
11. Effect of TiB2 on dry-sliding tribological properties of TiAl intermetallics10.1016/j.triboint.2013.02.006 ↗
12. Effects of niobium particles on the wear behavior of powder metallurgical γ-TiAl alloy in different environments
13. Sliding wear of TiAl intermetallics against steel and ceramics of Al2O3, Si3N4 and WC/Co10.1016/j.wear.2006.01.044 ↗
14. Effects of niobium on phase composition and improving mechanical properties in TiAl alloy reinforced by Ti2AlC10.1016/j.intermet.2019.106630 ↗
15. Effect of Ag and Ti3SiC2 on tribological properties of TiAl matrix self-lubricating composites at room and increased temperatures10.1007/s11249-014-0299-y ↗
16. Grinding mechanism and mechanical properties of the in-situ synthesized Al2O3/TiAl composites10.1016/j.ceramint.2019.03.111 ↗
17. Investigation of the characteristics and corrosion resistance of Al2O3/TiN coatings10.1016/j.apsusc.2005.09.075 ↗
18. Effect of Nb2O5 on the microstructure and mechanical properties of TiAl based composites produced by hot pressing10.1016/j.msea.2011.04.062 ↗
19. Microstructure and mechanical properties of in-situ synthesized Al2O3/TiAl composites10.1016/S1000-9361(08)60174-0 ↗
20. Investigation of tribological and mechanical properties Al2O3-SiC reinforced Al composites manufactured by casting or P/M method10.1016/j.matdes.2008.04.014 ↗
21. Electrochemical corrosion of Ti-Al2O3 biocomposites in Ringer's solution10.1016/j.jallcom.2018.09.313 ↗
22. Effect of Al2O3 on the microstructure and mechanical properties of Ti3AlC2/Al2O3 in situ composites synthesized by reactive hot pressing10.1016/j.ceramint.2012.03.060 ↗
23. Fabrication and mechanical properties of Al2O3/TiAl in situ composites doped with Nb2O510.2298/SOS1503311W ↗
24. Sintering behaviour and microstructures of Ti(Al,O)/Al2O3, Ti3Al(O)/Al2O3 and TiAl(O)/Al2O3 in situ composites10.1016/j.msea.2006.01.030 ↗
25. Mechanical properties and microstructure of Al2O3/TiAl in situ composites doped with Cr and V2O510.2298/SOS1201073Z ↗
26. Microstructure characterization and mechanical properties of TiAl-based alloys prepared by mechanical milling and spark plasma sintering10.1016/j.matchar.2017.03.016 ↗
27. TiAl based alloy with excellent mechanical performance prepared by gas atomization and spark plasma sintering10.1016/j.intermet.2012.07.006 ↗
28. In situ synthesis of Ti2AlC–Al2O3/TiAl composite by vacuum sintering mechanically alloyed TiAl powder coated with CNTs10.1016/j.jallcom.2013.06.109 ↗
29. Fabrication of a powder metallurgy Ti2AlNb-based alloy by spark plasma sintering and associated microstructure optimization10.1016/j.matdes.2015.10.042 ↗
30. Lamellar structure and effect of Ti2AlC on properties of prepared in-situ TiAl matrix composites10.1016/j.ceramint.2016.05.152 ↗
31. Reassessment of the binary aluminum-titanium phase diagram10.1361/154770306X109809 ↗
32. Mechanical properties and microstructure of Al2O3/TiAl in situ composites doped with Cr2O310.1016/j.msea.2011.01.006 ↗
33. Effect of characteristics of submicrometer powder on the sintering behaviors of Al2O3 ceramic
34. Lamellar orientation control in TiAl base alloys by a Two-step compression process at high temperature10.1016/j.msea.2008.12.027 ↗
35. Low temperature phase transformations in copper-quenched Ti-44.5Al-8Nb-2.5V alloy10.3390/ma10020201 ↗
36. Microstructure evolution in TiAl alloys with B additions: conventional solidification10.1007/BF02663215 ↗
37. Dynamic recrystallization behavior during hot deformation and mechanical properties of 0.2 μm SiC preinforced Mg matrix composite10.1016/j.msea.2012.10.044 ↗
38. Influence of C and B elements on structures and mechanical properties for high Nb containing TiAl alloy
39. Effects of alloy elements on the compression properties of in-situ nano-Ti5Si3/TiAl composite
40. Measurement of the corrosion rate of magnesium alloys using Tafel extrapolation10.1016/j.corsci.2009.10.016 ↗
41. Subtractive manufacturing of stable hierarchical micro-nano structures on AA5052 sheet with enhanced water repellence and durable corrosion resistance10.1016/j.matdes.2019.108152 ↗
42. The microstructures and mechanical properties of V2O5-Doped Al2O3/TiAl in-situ composites by reactive hot pressing process10.1007/s11665-013-0673-1 ↗
43. Enhanced high temperature corrosion resistance of Al2O3/Al composite coating on γ-TiAl alloy10.1016/S1875-5372(18)30123-1 ↗
44. Advances in gamma titanium aluminides and their manufacturing techniques10.1016/j.paerosci.2012.04.001 ↗
45. Investigation on microstructural, mechanical and electrochemical properties of aluminum composites reinforced with graphene nanoplatelets10.1016/j.pnsc.2015.09.005 ↗
46. Dislocation generation due to differences between the coefficients of thermal expansion10.1016/0025-5416(86)90261-2 ↗
47. Comparative study of the compression properties of TiAl matrix composites reinforced with nano-TiB2, and nano-Ti5Si3 particles10.1016/j.msea.2012.10.001 ↗
48. Alloying mechanism of beta stabilizers in a TiAl alloy10.1007/s11661-001-0136-4 ↗
49. Enhancing the properties of magnesium using SiC particulates in sub-micron length scale10.1002/adem.200400105 ↗
50. Synergetic effect of graphene nanoplatelets (GNPs) and multi-walled carbon nanotube (MW-CNTs) on mechanical properties of pure magnesium10.1016/j.jallcom.2014.03.038 ↗
51. Analysis on the factors influencing quantity of crystallized grains cooling rate and wetting angle
52. Production of Al2O3-Ti2AlN composite with novel combination of high temperature properties10.1016/j.msea.2014.03.101 ↗
53. Microstructure, mechanical and tribological properties of TiAl-based composites reinforced with high volume fraction of nearly network Ti2AlC particulates
54. Preparation and friction characteristics of brake pad made from ceramic composite materials
55. Tribological behavior of Al/SiC and Al/SiC/2 vol% Gr nanocomposites containing different amounts of nano SiC particles10.1088/2053-1591/ab0929 ↗
56. Structural, mechanical and tribological properties of A356 aluminium alloy reinforced with Al2O3, SiC and SiC +graphite particles10.1016/j.jallcom.2010.07.028 ↗
57. Corrosion of Al2O3-Ti composites under inflammatory condition in simulated physiological solution10.1016/j.msec.2019.04.047 ↗