Investigation of a novel sub-surface work hardening phenomenon in micro-turning of Zr-based bulk metallic glass
Source abstract
Abstract
This study investigates the influence of the micro-turning operation on the subsurface deformation-induced transformation. The variations in nanohardness, shear transformation zone (STZ) volume, and free volume in the machined subsurface of the Zr-based bulk metallic glass (BMG) have been characterized. Nanoindentation studies reveal that the machined subsurface is strain hardened, a unique phenomenon that has not been reported in Zr-based BMG machining. The work-hardened zone extends until a depth of ∼20 μm from the surface. The quantitative evaluation of the deformation-induced hardening has been done experimentally by nanoindentation followed by the free volume characterization via Differential Scanning Calorimetry (DSC). The Shear Transformation Zone (STZ) volume approach has been used to understand the changes in the machined subsurface induced due to microturning. The STZ volume in the machined region is lower than that in the undeformed zone for all the machining conditions investigated in this work. The enthalpy change obtained using DSC analysis for estimating the change in free volume content of the machined regions correlates with the STZ volume.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallic Glasses and Amorphous Alloys · Cultural Heritage Materials Analysis · Phase-change materials and chalcogenides
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. Chip formation, cutting forces, and tool wear in turning of Zr-based bulk metallic glass10.1016/j.ijmachtools.2004.02.002 ↗
2. Light emission, chip morphology, and burr formation in drilling the bulk metallic glass10.1016/j.ijmachtools.2004.11.004 ↗
3. Oxidation and crystallization of Zr-based bulk metallic glass due to machining10.1016/j.intermet.2003.09.017 ↗
4. Investigation on chip deformation behaviors of Zr-based bulk metallic glass during machining10.1016/j.jmatprotec.2019.116404 ↗
5. Investigation on chip formation and surface morphology in orthogonal machining of Zr-based bulk metallic glass10.1016/j.mfglet.2019.01.002 ↗
6. Mechanism of chip segmentation in orthogonal cutting of zr-based bulk metallic glass10.1115/1.4043837 ↗
7. Laser processing of bulk metallic glass: a review10.1016/j.jmatprotec.2017.03.034 ↗
8. Experimental study on wire-electrical discharge machining of zirconium-based metallic glass10.1088/2053-1591/ab2773 ↗
9. Processing of zirconium-based bulk metallic glass (BMG) using micro electrical discharge machining (Micro-EDM)10.1080/10426910903129661 ↗
10. On the surface characteristics of a Zr-based bulk metallic glass processed by microelectrical discharge machining10.1016/j.apsusc.2015.08.239 ↗
11. Strain hardening and recovery in a bulk metallic glass under nanoindentation10.1016/j.scriptamat.2005.12.049 ↗
12. Cooling-rate induced softening in a Zr 50 Cu 50 bulk metallic glass10.1063/1.2678909 ↗
13. Bulk metallic glass composites with transformation‐mediated work‐hardening and ductility10.1002/adma.201000482 ↗
14. Tensile deformation micromechanisms for bulk metallic glass matrix composites: from work-hardening to softening10.1016/j.actamat.2011.03.036 ↗
15. “Work-hardenable” ductile bulk metallic glass10.1103/PhysRevLett.94.205501 ↗
16. Mechanical behavior of amorphous alloys10.1016/j.actamat.2007.01.052 ↗
17. Plastic deformation in metallic glasses10.1016/0001-6160(79)90055-5 ↗
18. A microscopic mechanism for steady state inhomogeneous flow in metallic glasses10.1016/0001-6160(77)90232-2 ↗
19. Anthony C. Fischer Cripps, Nanoindentation.
20. Densification and strain hardening of a metallic glass under tension at room temperature10.1103/PhysRevLett.111.135504 ↗
21. Experimental characterization of shear transformation zones for plastic flow of bulk metallic glasses10.1073/pnas.0806051105 ↗
22. A universal criterion for plastic yielding of metallic glasses with a (T/T g) 2/3 temperature dependence10.1103/PhysRevLett.95.195501 ↗
23. Yield point of metallic glass10.1016/j.actamat.2006.05.024 ↗
24. Theory of shear banding in metallic glasses and molecular dynamics calculations10.2320/matertrans.MJ200769 ↗
25. Plastic flow and failure resistance of metallic glass: insight from in situ compression of nanopillars10.1103/PhysRevB.77.155419 ↗
26. Approaching the ideal elastic limit of metallic glasses10.1038/ncomms1619 ↗
27. Effects of very high pressures on glass10.1063/1.1721294 ↗
28. Poisson's ratio and the densification of glass under high pressure10.1103/PhysRevLett.100.225501 ↗
29. Stress‐induced densification of glassy polymers in the subyield region10.1002/(SICI)1097-4628(19991114)74:7<1705::AID-APP14>3.0.CO;2-4 ↗
30. Investigation on hardening behavior of metallic glass under cyclic indentation loading via molecular dynamics simulation10.1016/j.apsusc.2017.04.125 ↗
31. The glass transition as a free volume related kinetic phenomenon10.1016/0956-7151(90)90142-4 ↗
32. Correlation between enthalpy change and free volume reduction during structural relaxation of Zr55Cu30Al10Ni5 metallic glass10.1016/j.scriptamat.2003.09.038 ↗
33. Ductile to brittle transition of fracture of a Zr-based bulk metallic glass: strain rate effect10.1016/j.intermet.2016.07.004 ↗
34. Shear transformation zone volume determining ductile–brittle transition of bulk metallic glasses10.1016/j.actamat.2010.12.006 ↗
35. Investigation of the softening behavior in severely deformed micromachined sub-surface of Zr-based bulk metallic glass via nanoindentation10.1016/j.jnoncrysol.2021.121280 ↗
36. The effect of simulated thermal cycling on thermal and mechanical stability of a Ti-based bulk metallic glass10.1016/j.jallcom.2013.05.194 ↗
37. Mechanical behavior of bulk metallic glass prepared by copper mold casting with reversed pressure10.1016/j.jmatprotec.2016.06.023 ↗